How do I safely use the Magnetic Chuck for Clamping Jaws of FINN-POWER P20 Presses to quickly replace jaw segments and ensure they stay aligned during operation?

Use the Magnetic Chuck for Clamping Jaws of FINN-POWER P20 Presses to replace jaw segments quickly, safely and with correct alignment by following these steps: 1. Prepare: Power down the press and follow lockout/tagout procedures. Wear appropriate PPE (gloves, safety glasses). 2. Remove old jaws: Open the press and expose the jaw area. Loosen and remove fasteners as required, keeping parts organized. 3. Position the Magnetic Chuck: Grip the Magnetic Chuck for Clamping Jaws of FINN-POWER P20 Presses by its ergonomically shaped plastic handle. Align the chuck so its locating pins match the holes in the new jaw segments. 4. Mount new segments: Let the integrated magnet hold each jaw segment to the chuck. The pins will fit into the segment holes to guarantee precise positioning; the magnet keeps the segments firmly in place during handling. 5. Install assembly: Bring the magnet-held, aligned jaw segments to the press and seat them in the jaw carriage. Ensure pins remain engaged in the holes to maintain alignment while you secure fasteners. 6. Secure and verify: Tighten all fasteners to the specified torque. Verify segment alignment and that nothing shifts during tightening. Cycle the press at low speed to confirm proper operation before returning to normal production. 7. Store and maintain: After use, clean the Magnetic Chuck for Clamping Jaws of FINN-POWER P20 Presses and store it safely. Inspect steel parts periodically for wear. Following these steps leverages the chuck’s pin alignment and integrated magnet to minimize downtime, maintain precise jaw alignment, and enhance operator safety.

Can the Magnetic Chuck for Clamping Jaws of FINN-POWER P20 Presses be used with worn or damaged jaw segments, and what precautions should I take?

Yes — the Magnetic Chuck for Clamping Jaws of FINN-POWER P20 Presses can be used with worn or damaged jaw segments, but with important precautions. - Suitability: The tool’s pins and magnet are designed to align and hold standard jaw segments, so it will physically assist handling even if segments show wear. - Inspection: Before use, inspect each jaw segment for cracks, severe deformation, missing material or compromised holes. Segments with structural damage should not be reused; the chuck can hold them but cannot restore integrity. - Secure fit: Ensure the chuck’s pins fully engage the segment holes. Excessive wear that enlarges or deforms the holes may prevent correct alignment and secure handling—replace such segments. - Safety: Because the chuck relies on a magnet to hold parts during replacement, always keep a firm grip on the handle and avoid handling segments above personnel or machine openings. If a segment is brittle or cracked, magnetic retention may fail. - Downtime & efficiency: Use the chuck to minimize handling time for reusable, worn-but-intact segments; remove and replace any segment that risks malfunction during operation. - Maintenance: Keep the chuck’s pins and magnet clean and undamaged to preserve reliable alignment and holding force. In short: the Magnetic Chuck for Clamping Jaws of FINN-POWER P20 Presses is suitable for handling worn segments if they remain structurally sound and their holes engage properly; replace any segments with structural damage or excessively worn alignment features to ensure safety and proper operation.

Magnetic Chuck for Clamping Jaws of FINN-POWER P20 Presses

Additional information

The innovative magnetic grip with an ergonomically shaped handle is designed to ensure quick and effortless replacement of a complete set of working jaws in FINN-POWER P20 crimping presses. Its smart construction allows the pins in the grip to perfectly align with the holes in the jaw segments, guaranteeing precise positioning and secure handling. Thanks to the integrated magnet, the jaw segments remain firmly in place during the entire replacement process, significantly reducing downtime and enhancing operator safety. The handle, made of durable plastic, provides a comfortable and reliable grip, while the steel components ensure long-lasting strength and resistance to wear. This practical solution not only streamlines workflow but also increases efficiency, making it an indispensable tool for professionals who value speed, accuracy, and convenience in their daily operations.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Price	Quantity	Actions	Catalogue
FPM-691043	Magnetic holder for working jaws series 20	-	-	In stock	0 €		Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +91 8 925 918 796 or email us: chennai@tubes-international.com

SEND ENQUIRY

The innovative magnetic grip with an ergonomically shaped handle is designed to ensure quick and effortless replacement of a complete set of working jaws in FINN-POWER P20 crimping presses. Its smart construction allows the pins in the grip to perfectly align with the holes in the jaw segments, guaranteeing precise positioning and secure handling. Thanks to the integrated magnet, the jaw segments remain firmly in place during the entire replacement process, significantly reducing downtime and enhancing operator safety. The handle, made of durable plastic, provides a comfortable and reliable grip, while the steel components ensure long-lasting strength and resistance to wear. This practical solution not only streamlines workflow but also increases efficiency, making it an indispensable tool for professionals who value speed, accuracy, and convenience in their daily operations.