Is the External Cutting Mandrel, FSE Type compatible with other FINN POWER tool holders besides the FS50?

Based on the provided description, the External Cutting Mandrel, FSE Type is specified as "fully compatible with the tool holder of the FINN POWER FS50 device." No information is given about compatibility with other FINN POWER tool holders. Therefore, you should assume it is only confirmed compatible with the FS50. If you need to use it with a different FINN POWER holder, verify directly with FINN POWER or the mandrel supplier for compatibility, adaptor availability, or required modifications.

Can the External Cutting Mandrel, FSE Type be used with hoses made from specialty materials (e.g., PTFE-lined or thermoplastic) without affecting cutting accuracy?

Yes — the External Cutting Mandrel, FSE Type can be used with hoses made from specialty materials (e.g., PTFE-lined or thermoplastic) without inherently compromising cutting accuracy, provided a few conditions are met. The mandrel’s precision-engineered design, robust construction and compatibility with the FINN POWER FS50 tool holder deliver stable, repeatable support for the hose outer layer across a wide size range (3/16"–2"), which helps maintain accurate machining even on non-standard materials. Key considerations to ensure accuracy with specialty hoses: - Material stiffness and wall construction: very soft or highly flexible linings may require careful clamping tension and correct mandrel size to avoid deformation during cutting. - Correct mandrel sizing and alignment: matching the mandrel diameter to the hose size and ensuring proper alignment in the FS50 tool holder prevents runout and preserves cut quality. - Cutting tool selection and speeds: adjust blade type, feed rate and spindle speed for PTFE or thermoplastic to avoid melting, tearing or burring. - Inspection and trial cuts: perform test cuts and inspect results to fine-tune setup for specific specialty constructions. - Maintenance and condition: keep the mandrel and tool holder in good condition to retain the mandrel’s dimensional accuracy and surface finish. When these precautions are followed, the External Cutting Mandrel, FSE Type will provide durable, accurate and consistent outer-layer machining for specialty hoses, supporting efficient preparation and reduced downtime.

Stem for skiving external, type FSE

Additional information

Material	CS – steel (cast iron)
Standard length [m]	60

Stem type FSE used for skiving outer layer rubber hoses hydraulic machinable. Compatible with handle tools devices FINN POWER FS50. W sizes: od 3/16″ for 2″.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
FP-FSE-03	Pin for cutting external 3/16"	-	-	In stock	Enquiry
FP-FSE-04	Pin for cutting external 1/4"	-	-	In stock	Enquiry
FP-FSE-05	Pin for cutting external 5/16"	-	-	In stock	Enquiry
FP-FSE-06	Pin for cutting external 3/8"	-	-	In stock	Enquiry
FP-FSE-08	Pin for cutting external 1/2"	-	-	In stock	Enquiry
FP-FSE-10	Pin for cutting external 5/8"	-	-	In stock	Enquiry
FP-FSE-12	Pin for cutting external 3/4"	-	-	In stock	Enquiry
FP-FSE-16	Pin for cutting external 1"	-	-	In stock	Enquiry
FP-FSE-20	Pin for cutting external 1.1/4"	-	-	In stock	Enquiry
FP-FSE-24	Pin for cutting external 1.1/2"	-	-	In stock	Enquiry
FP-FSE-32	Pin for cutting external 2"	-	-	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +91 8 925 918 796 or email us: chennai@tubes-international.com

SEND ENQUIRY

Stem type FSE used for skiving outer layer rubber hoses hydraulic machinable. Compatible with handle tools devices FINN POWER FS50. W sizes: od 3/16″ for 2″.