Can Clamp DIN 3015 Standard, Polyamide, Type 100 be welded directly to metal structures or should I use bolts/rails for marine applications?

Clamp DIN 3015 Standard, Polyamide, Type 100 Format: Yes — the carbon steel base of the Type 100 clamp can be welded directly to metal structures, making it a valid option for marine applications. The product description explicitly states the base can be welded, and it also offers alternative mounting methods (bolts or rail systems) if welding is undesirable or impractical. For marine use consider: - Corrosion protection: welded joints and base should be protected or treated to resist seawater corrosion (coatings, stainless options, or sacrificial anodes). - Thermal and mechanical loads: ensure welding does not degrade the polyamide or compromise clamp alignment; maintain appropriate distances/insulation if needed. - Vibration and maintenance access: bolted or rail-mounted systems can simplify replacement and reduce stress transfer in high-vibration areas. If in doubt about material choices, coatings, or the best mounting method for a specific vessel or environment, consult TUBES INTERNATIONAL® for optimal configuration and component selection.

Is Clamp DIN 3015 Standard, Polyamide, Type 100 suitable for high-temperature marine engine spaces up to +180°C without additional thermal protection?

Clamp DIN 3015 Standard, Polyamide, Type 100 Format is rated for an operating temperature range up to +180°C. However, suitability for high-temperature marine engine spaces up to +180°C without additional thermal protection depends on several practical factors: - Material limit: Polyamide is specified up to +180°C; continuous exposure near the upper limit can reduce mechanical properties and service life compared with lower-temperature use. - Exposure type: Intermittent short peaks at or slightly above +180°C may be tolerated; continuous ambient temperatures at +180°C plus radiant heat from nearby engines/exhausts increase risk of softening, creep or accelerated ageing. - Marine environment: Salt, oil, vibration and mechanical loads typical in engine rooms can compound thermal effects; polyamide can be more vulnerable under combined stressors. - Safety margin: For critical pipe supports in engine spaces, industry practice often prefers metallic clamps or additional thermal shielding when temperatures approach material limits to ensure long-term reliability and safety. Recommendation: If actual exposure is reliably below +180°C with limited peaks, careful selection and monitoring might allow use without extra protection. For continuous or uncertain high-heat exposure in marine engine spaces, provide thermal protection or choose metal clamps. Consult TUBES INTERNATIONAL® or the project engineer for a site-specific assessment and long-term suitability.

Clamp DIN 3015 Standard, Polyamide, Type 100

All products, Clamps for hydraulic pipes/

Additional information

Material	P – material (plastic)

The DIN 3015 standard clamp type 100 (without top plate) provides a reliable and efficient solution for fastening pipes, tubes, and hoses in a wide range of industrial applications, including both land-based and marine installations. Designed for quick assembly and long-lasting performance, the clamp ensures secure and visually neat mounting while meeting the strict requirements of the DIN 3015 standard. The base can be welded directly to the structure, with alternative options for bolting or rail mounting to suit different installation needs. The profiled interior surface guarantees a stable grip on the pipe, while the fastening system varies depending on size: one hexagon socket screw for group 0 and two screws for groups 1 to 6. Manufactured from self-extinguishing polyamide with galvanized steel screws and a carbon steel base, the clamp offers excellent durability and resistance to demanding conditions, with an operating temperature range from -40°C to +180°C. To enhance flexibility, additional accessories such as extended plates, rails, and mounting screws are available, allowing tailored solutions for specific projects. For optimal configuration and selection of components, consultation with TUBES INTERNATIONAL® is recommended.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
TC-PA100-006	DIN3015 standard PA clamp for 6 mm pipe, without mounting plate.	-	-	In stock	Enquiry
TC-PA100-008	DIN3015 standard PA clamp for 8 mm pipe, without mounting bracket.	-	-	In stock	Enquiry
TC-PA100-010	DIN3015 standard PA clamp for 10 mm pipe, without mounting bracket.	-	-	In stock	Enquiry
TC-PA100-012	DIN3015 standard PA clamp for 12 mm pipe, without mounting bracket.	-	-	In stock	Enquiry
TC-PA100-106	DIN3015 standard PA clamp for 6 mm pipe, without mounting bracket.	-	-	In stock	Enquiry
TC-PA100-106,4	DIN3015 standard PA clamp for 6.4 mm pipe, without rubber lining.	-	-	In stock	Enquiry
TC-PA100-108	DIN3015 standard PA clamp for 8 mm pipe, without mounting hardware.	-	-	In stock	Enquiry
TC-PA100-109,5	DIN3015 standard PA clamp for 9.5 mm pipe, without p. g.	-	-	In stock	Enquiry
TC-PA100-110	DIN3015 standard PA clamp for 10 mm pipe, without rubber lining.	-	-	In stock	Enquiry
TC-PA100-112	DIN3015 standard PA clamp for 12 mm pipe, without mounting bracket.	-	-	In stock	Enquiry
TC-PA100-212,7	DIN3015 standard PA clamp for 12.7 mm pipe, without mounting.	-	-	In stock	Enquiry
TC-PA100-213,5	DIN3015 standard PA clamp for 13.5 mm pipe, without p. g.	-	-	In stock	Enquiry
TC-PA100-214	DIN3015 standard PA clamp for 14 mm pipe, without mounting bracket.	-	-	In stock	Enquiry
TC-PA100-215	DIN3015 standard PA clamp for 15 mm pipe, without mounting bracket.	-	-	In stock	Enquiry
TC-PA100-216	DIN3015 standard PA clamp for 16 mm pipe, without mounting accessories.	-	-	In stock	Enquiry
TC-PA100-217,2	DIN3015 standard PA clamp for 17.2 mm pipe, without p. g.	-	-	In stock	Enquiry
TC-PA100-218	DIN3015 standard PA clamp for 18 mm pipe, without p. g.	-	-	In stock	Enquiry
TC-PA100-219	DIN3015 standard PA clamp for 19 mm pipe, without mounting bracket.	-	-	In stock	Enquiry
TC-PA100-319	DIN3015 standard PA clamp for 19 mm pipe, without mounting bracket.	-	-	In stock	Enquiry
TC-PA100-320	DIN3015 standard PA clamp for 20 mm pipe, without p. g.	-	-	In stock	Enquiry
TC-PA100-321,3	DIN3015 standard PA clamp for 21.3 mm pipe, without p. g.	-	-	In stock	Enquiry
TC-PA100-322	DIN3015 standard PA clamp for 22 mm pipe, without p. g.	-	-	In stock	Enquiry
TC-PA100-325	DIN3015 standard PA clamp for 25 mm pipe, without mounting bracket.	-	-	In stock	Enquiry
TC-PA100-325,4	DIN3015 standard PA clamp for 25.4 mm pipe, without p. g.	-	-	In stock	Enquiry
TC-PA100-426,9	DIN3015 standard PA clamp for 26.9 mm pipe, without p. g.	-	-	In stock	Enquiry
TC-PA100-428	DIN3015 standard PA clamp for 28 mm pipe, without p. g.	-	-	In stock	Enquiry
TC-PA100-430	DIN3015 standard PA clamp for 30 mm pipe, without p. g.	-	-	In stock	Enquiry
TC-PA100-432	DIN3015 standard PA clamp for 32 mm pipe, without mounting bracket.	-	-	In stock	Enquiry
TC-PA100-532	DIN3015 standard PA clamp for 32 mm pipe, without mounting bracket.	-	-	In stock	Enquiry
TC-PA100-533,7	DIN3015 standard PA clamp for 33.7 mm pipe, without p. g.	-	-	In stock	Enquiry
TC-PA100-535	DIN3015 standard PA clamp for 35 mm pipe, without rubber lining.	-	-	In stock	Enquiry
TC-PA100-538	DIN3015 standard PA clamp for 38 mm pipe, without mounting bracket.	-	-	In stock	Enquiry
TC-PA100-540	DIN3015 standard PA clamp for 40 mm pipe, without p. g.	-	-	In stock	Enquiry
TC-PA100-542	DIN3015 standard PA clamp for 42 mm pipe, without p. g.	-	-	In stock	Enquiry
TC-PA100-542,4	DIN3015 standard PA clamp for 42.4 mm pipe, without p. g.	-	-	In stock	Enquiry
TC-PA100-545	DIN3015 standard PA clamp for 45 mm pipe, without p. g.	-	-	In stock	Enquiry
TC-PA100-644,5	DIN3015 standard PA clamp for 44.5 mm pipe, without p. g.	-	-	In stock	Enquiry
TC-PA100-648,3	DIN3015 standard PA clamp for 48.3 mm pipe, without p. g.	-	-	In stock	Enquiry
TC-PA100-650,8	DIN3015 standard PA clamp for 50.8 mm pipe, without mounting bracket.	-	-	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +91 8 925 918 796 or email us: chennai@tubes-international.com

SEND ENQUIRY

The DIN 3015 standard clamp type 100 (without top plate) provides a reliable and efficient solution for fastening pipes, tubes, and hoses in a wide range of industrial applications, including both land-based and marine installations. Designed for quick assembly and long-lasting performance, the clamp ensures secure and visually neat mounting while meeting the strict requirements of the DIN 3015 standard. The base can be welded directly to the structure, with alternative options for bolting or rail mounting to suit different installation needs. The profiled interior surface guarantees a stable grip on the pipe, while the fastening system varies depending on size: one hexagon socket screw for group 0 and two screws for groups 1 to 6. Manufactured from self-extinguishing polyamide with galvanized steel screws and a carbon steel base, the clamp offers excellent durability and resistance to demanding conditions, with an operating temperature range from -40°C to +180°C. To enhance flexibility, additional accessories such as extended plates, rails, and mounting screws are available, allowing tailored solutions for specific projects. For optimal configuration and selection of components, consultation with TUBES INTERNATIONAL® is recommended.