Braided hose for high-purity applications, with low absorption and adsorption TYGON® 2475 IB

Additional information

Material

TPE – thermoplastic elastomer

Maximum operating temperature [°C]

52

Vacuum resistance

yes

Standard length [m]

15, 3, 7.5

Reinforcement

synthetic braid

Colourless, transparent, flexible hose reinforced with polyester braid for biopharmaceutical applications, completely free of plasticisers and oils. Designed for higher pressures, e.g. in single-use ultrafiltration / diafiltration systems, chromatography, water for injection (WFI), deionised water, pharmaceutical and cosmetic substances. Features hydrophobicity (non-wettability) and very low absorption and adsorption of water-based fluids compared with PVC, as well as lower gas permeability than silicone hoses, protecting sensitive fluids against oxidation. This minimises the risk of changes in fluid properties even with repeated hose use. The glass-smooth, non-porous inner surface prevents contaminants from depositing and adhering, facilitating complete fluid drainage and hose cleaning. Resistant to chemical cleaning agents and disinfectants. Offers good chemical resistance to a range of substances: acids, alkalis, salts, as well as alcohols and ketones. Not recommended for hydrocarbons. Meets USP Class VI requirements. Hygienic properties are confirmed by the Saint-Gobain validation guide for this hose. Suitable for ethylene oxide or radiation sterilisation (up to 4.5 kGy). Complies with RoHS 2011/65/EU and REACH 1907/2006/EU. Can be used as a single-use or reusable product. Disposal of used hoses does not release hazardous substances (e.g. chlorine); incineration produces only carbon dioxide and water. Pressure safety factor 4:1. Assembly on hose tails and fittings using clips and clamps. Maximum working pressure is specified at 23°C. Material: polyolefin. Maximum working temperature: up to +52°C. Brittleness temperature: -78°C. Hardness: 72 Shore (A). Density: 0.9 g/cm³. Note: Product prepared in the Tubes International CLEAN ROOM in compliance with strict cleanliness standards. Product is non-returnable

List of product variants

Article numberProduct variant nameDNBARAvailabilityPriceQuantityActionsCatalogue
VE-ACX00019Hose TYGON 2475 IB 6.4x12.7 mm615.5In stock0 €
Enquiry
VE-ACX00029Hose TYGON 2475 IB 9.5x15.9 mm1014.5In stock0 €
Enquiry
VE-ACX00038Hose TYGON 2475 IB 12.7x19.1 mm1215.9In stock0 €
Enquiry
VE-ACX00046Hose TYGON 2475 IB 15.9x22.3 mm169.3In stock0 €
Enquiry
VE-ACX00054Hose TYGON 2475 IB 19x27 mm209.3In stock0 €
Enquiry
VE-ACX06074Hose TYGON 2475 IB 38x50.8 mm38In stock0 €
Enquiry
VE-ACX42064Hose TYGON 2475 IB 25.4x35 mm258.6In stock0 €
Enquiry

Do you need a larger quantity of products or a bespoke quote?

Colourless, transparent, flexible hose reinforced with polyester braid for biopharmaceutical applications, completely free of plasticisers and oils. Designed for higher pressures, e.g. in single-use ultrafiltration / diafiltration systems, chromatography, water for injection (WFI), deionised water, pharmaceutical and cosmetic substances. Features hydrophobicity (non-wettability) and very low absorption and adsorption of water-based fluids compared with PVC, as well as lower gas permeability than silicone hoses, protecting sensitive fluids against oxidation. This minimises the risk of changes in fluid properties even with repeated hose use. The glass-smooth, non-porous inner surface prevents contaminants from depositing and adhering, facilitating complete fluid drainage and hose cleaning. Resistant to chemical cleaning agents and disinfectants. Offers good chemical resistance to a range of substances: acids, alkalis, salts, as well as alcohols and ketones. Not recommended for hydrocarbons. Meets USP Class VI requirements. Hygienic properties are confirmed by the Saint-Gobain validation guide for this hose. Suitable for ethylene oxide or radiation sterilisation (up to 4.5 kGy). Complies with RoHS 2011/65/EU and REACH 1907/2006/EU. Can be used as a single-use or reusable product. Disposal of used hoses does not release hazardous substances (e.g. chlorine); incineration produces only carbon dioxide and water. Pressure safety factor 4:1. Assembly on hose tails and fittings using clips and clamps. Maximum working pressure is specified at 23°C. Material: polyolefin. Maximum working temperature: up to +52°C. Brittleness temperature: -78°C. Hardness: 72 Shore (A). Density: 0.9 g/cm³. Note: Product prepared in the Tubes International CLEAN ROOM in compliance with strict cleanliness standards. Product is non-returnable

Additional information

Material

TPE – thermoplastic elastomer

Maximum operating temperature [°C]

52

Vacuum resistance

yes

Standard length [m]

15, 3, 7.5

Reinforcement

synthetic braid

Do you need a larger quantity of products or a bespoke quote?

Sales Network
Check

Inquiry
Send

Related Products

If you need help choosing a product or haven’t found the right one?