0

Our products

    Filters
      Product categories
      Working pressure [bar]
      Minimum operating temperature [°C]

      Minimum operating temperature [°C]: -273 — 260

      Maximum operating temperature [°C]

      Maximum operating temperature [°C]: 30 — 1100

      Material
      Vacuum resistance
      Standard length [m]
        • Non-drip quick coupling for liquids DN9, with a female BSP thread, stainless steel, CEJN – NON DRIP
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          Non-spill DN19 flat-face quick couplings designed for conveying liquids (water, oil, chemicals, etc.). Flat mating surfaces minimise potential fluid leakage and prevent air inclusion while making the quick coupling easy to keep clean. Sockets and plugs are available with or without a shut-off valve and can be combined interchangeably to provide three quick coupling configurations: straight-through (sockets and plugs without valves), single shut-off (socket with a valve, plug without a valve) and double shut-off (non-spill, socket and plug with valves). Caps are available to protect the quick coupling against contamination when disconnected. For additional safety where incorrect socket-plug connections are unacceptable, the quick coupling can be colour-coded. Green identification rings are offered as standard. Optional colours: black, blue, red, white, yellow, or so-called key coding (the socket and plug have additional grooves and projections that allow connection only when correctly matched). Material: AISI 316 steel. Seal: NBR, Viton. Working pressure: 20 bar. Working temperature: from -15°C to +100°C - NBR, from -20°C to +205°C - Viton (up to +125°C for identification rings).
        • Non-drip quick coupling for liquids DN9, with a female BSP thread, stainless steel, CEJN – NON DRIP
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          DN4 flat-face dry-break quick coupling designed for transferring liquids (water, oil, chemicals, etc.). Flat mating surfaces minimise potential fluid leakage and prevent air inclusion while making the quick coupling easy to keep clean. Socket and plug with shut-off valves. Caps are available to protect the quick coupling against contamination when disconnected. For additional safety where incorrect socket-to-plug connections are unacceptable, the quick coupling can be colour-coded. Green identification rings are supplied as standard. Optional colours: black, blue, red, white or yellow. Mechanical key coding is also available (the socket and plug have additional grooves and projections that allow the quick coupling to connect only when correctly matched). Material: AISI 316 steel. Seal: Viton. Working pressure: 20 bar. Working temperature: from -20°C to +205°C - Viton (up to +125°C for identification rings).
        • Non-drip quick coupling for liquids DN9, with a female BSP thread, stainless steel, CEJN – NON DRIP
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          DN6 flat-face dry-break quick coupling designed for transferring liquids (water, oil, chemicals, etc.). Flat mating surfaces minimise potential fluid leakage and prevent air inclusion while making the quick coupling easy to keep clean. Socket and plug with shut-off valves. Caps are available to protect the quick coupling against contamination when disconnected. For additional safety where incorrect socket-to-plug connections are unacceptable, the quick coupling can be colour-coded. Green identification rings are supplied as standard. Optional colours: black, blue, red, white or yellow. Mechanical key coding is also available (the socket and plug have additional grooves and projections that allow the quick coupling to connect only when correctly matched). Material: AISI 316 steel. Seal: Viton. Working pressure: 20 bar. Working temperature: from -20°C to +205°C - Viton (up to +125°C for identification rings).
        • Non-drip quick coupling for liquids DN9, with a female BSP thread, stainless steel, CEJN – NON DRIP
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          Non-spill DN9 flat-face quick couplings designed for transferring liquids (water, oil, chemicals, etc.). Flat mating surfaces minimise potential fluid leakage and prevent air inclusion while making the quick coupling easy to keep clean. Sockets and plugs are available with or without a shut-off valve and can be combined interchangeably to provide three quick coupling configurations: straight-through (socket and plug without valves), single shut-off (socket with valve, plug without valve) and double shut-off (non-spill, socket and plug with valves). Caps are available to protect the quick coupling from contamination when disconnected. For additional safety where incorrect socket-to-plug connections must be prevented, quick couplings can be colour-coded. Green identification rings are supplied as standard. Optional colours: black, blue, red, white, yellow; alternatively, key coding is available (the socket and plug have additional grooves and projections that allow the quick coupling to connect only when correctly matched). Material: AISI 316 steel. Seal: NBR, Viton. Working pressure: 20 bar. Working temperature: from -15°C to +100°C - NBR, from -20°C to +205°C - Viton (up to +125°C for identification rings).
        • A hydraulic quick coupling Leak-free ISO-F, plug with female thread BSP and pressure eliminator, zinc-nickel coated steel, HOLMBURY, type IFP
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          Plug for ISO-F “flat-face” non-spill quick coupling, type IF, with a female BSP thread and pressure eliminator. Intended mainly for construction machinery subject to large pressure surges. The zinc-nickel coating provides several times greater corrosion resistance than a zinc coating. Interchangeable with ISO-F quick couplings from other manufacturers. Application: hydraulic power systems (hydraulic oil). Material: steel with a zinc-nickel coating. Socket seal: NBR. Working temperature: from -25°C to +100°C. Working pressure: up to 350 bar (depending on the quick coupling size). Maximum static pressure when connecting quick couplings using a plug with a pressure eliminator: 0 bar on the socket side, 350 bar on the plug side. Flow rate is specified for a pressure drop of 3 bar.
        • Disc + blade holder for EST-S tool
          Select options This product has multiple variants. The options may be chosen on the product page / Details

          Disc + blade holder for EST-S tool

          All products | Hose and tube assembling machines
          0 €
          Disc + blade holder for the EST-S tool intended for cutting the outer rubber layer of skivable hydraulic hoses. Material: carbon steel, zinc-plated.
        • Thermoplastic freon hose with thermoplastic polymer cover FR5T
          Select options This product has multiple variants. The options may be chosen on the product page / Details

          Thermoplastic freon hose with thermoplastic polymer cover FR5T

          All products | Hoses and fittings for air conditioning
          0 €
          Lightweight, flexible hose designed for industrial refrigeration systems (an alternative to copper tubing), for domestic and industrial HVAC installations and automotive air conditioning (for filling and testing functions only). In particular for R134a, R404A, R407C, R410A, R1234yf, R1234ze, R290, R32 refrigerants and PAG, POE, PVE and AB type compressor oils. Waterproof outer layer, resistant to bending and abrasion. Vacuum value: 5 mbar (absolute pressure). Standards: EN 1736, ISO 13971 class I, UL1963. Assembly: use ZC-FR (IT-202) type fittings. Inner layer: polyamide (PA) separated by a layer of thermoplastic polymer. Reinforcement: polyester braid. Outer layer: thermoplastic polymer. Working pressure: 120 bar. Operating temperature: from -40°C to +120°C (momentarily +130°C).
        • Flame-retardant pneumatic hose for railway applications EN 45545-2, KKS-NEO
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          Special hose made of polyurethane meeting high fire protection requirements for rail vehicles, in particular the railway standard EN 45545-2. Flame retardant (UL 94 V2 to V0), halogen-free, self-extinguishing. Compliant with EN 45545-2:2016 - the hose meets hazard levels HL1, HL2, HL3 for R24 requirements - provided that the weight of a single hose section does not exceed 0.5 kg and they are adequately spaced apart from each other. Depending on requirements, the hose's flame-retardant properties can be used in other applications: in construction, industry, machine and vehicle manufacturing. The hose is resistant to hydrolysis, microorganisms, abrasion and UV radiation. Can be used for air, water and other liquids and gases. Characterized by good chemical resistance to fuels, solvents, detergents. Small bend radius facilitates hose assembly installation. Calibrated outer diameter allows connection using push-in fittings. Hoses with an outer diameter of 4, 14 and 16 mm are available on special order. Note: when used for vacuum, the minimum bend radius should be increased by approximately 20%. Available colors: blue, black. Hose material: polyurethane PUR (polyether-based). Hardness: 56 Shore (D). Working pressure: from 8 bar to 13 bar, depending on hose diameter. Operating temperature: from -35°C to +100°C (working pressure depends on temperature).
        • "Y" branch connector for coolant, system 1/4", LOC-LINE®
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          "Y" tee distributor for LOC-LINE® coolant hoses - 1/4" system. Material: acetal. Working pressure: up to 3 bar. Working temperature: up to +76°C.
        • Tee for HP connections up to 4140 bar, steel AISI 316
          Select options This product has multiple variants. The options may be chosen on the product page / Details

          Tee for HP connections up to 4140 bar, steel AISI 316

          All products | UHP adapters and accessories
          0 €
          Tee, for high-pressure connections in the HP version, suitable for operation under working pressure up to 4140 bar. The set includes three nuts and three back-up rings. Designed for use with liquid and gaseous media. Material: AISI 316 steel. Working pressure: up to 4140 bar.
        • Tee for MP connections up to 1380 bar, steel AISI 316
          Select options This product has multiple variants. The options may be chosen on the product page / Details

          Tee for MP connections up to 1380 bar, steel AISI 316

          All products | UHP adapters and accessories
          0 €
          A tee for high-pressure connections in the MP version, designed to operate at working pressures up to 1380 bar. The set includes three nuts and three back-up rings. Intended for use with liquid and gaseous media. Material: AISI 316 steel. Working pressure: up to 1380 bar.
        • Tee type "T" Pure-Fit® SIB®, polypropylene or PVDF, system BarbLock®
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          The Pure-Fit ® "T"-type tee is designed for Sani-Tech ® STHT ®, C-Flex ® and PharMed ® BPT biopharmaceutical hoses. It can also be used with other hoses of similar material (silicone, thermoplastic elastomer). The fitting is made of high-quality, high-purity plastic: polypropylene (PP) or polyvinylidene fluoride (PVDF), meeting the hygienic requirements of USP Class VI and/or USP and ISO 10993-5, free of BPA (Bisphenol A) and animal-derived substances. Hygienic properties confirmed by the Saint-Gobain validation guide. The Pure-Fit ® fitting should be mounted on the hose using special clamps (BarbLock ® system). The two parts of the clamp, slid onto each other, compress the hose around its entire circumference (360°), ensuring complete tightness of the connection, while also providing a smooth, stepless transition between the inner surface of the hose and the inside of the fitting tail (Smooth Inner Bore). This eliminates turbulence and dead spaces - flow stagnation areas that can be a site for bacterial growth. The use of Pure-Fit ® fittings mounted with Pure-Fit ® / BarbLock ® clamps provides significantly better tightness and hygienic properties of the connection compared to mounting with clamps/bands. Sterilization: by radiation (PP) or by radiation and in an autoclave (PVDF). Material: polypropylene (PP) or PVDF. Hardness: 85 Shore (A) (PP) or 78 Shore (A) (PVDF). Working pressure: 17 bar (20°C), 7 bar (93°C). Operating temperature: up to 93°C (PP) or up to 135°C (PVDF).
        • Tee type "Y" Pure-Fit® SIB®, polypropylene or PVDF, system BarbLock®
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          Pure-Fit® "Y" tee fitting is intended for Sani-Tech® STHT®, C-Flex® and PharMed® BPT biopharmaceutical hoses. It can also be used with other hoses of similar material (silicone, thermoplastic elastomer). The fitting is made of high-quality, high-purity plastic: polypropylene (PP) or polyvinylidene fluoride (PVDF), meeting the hygienic requirements of USP Class VI and/or USP and ISO 10993-5, containing no BPA (Bisphenol A) or substances of animal origin. Hygienic properties are confirmed by the Saint-Gobain validation guide. The Pure-Fit® fitting should be mounted onto the hose using special fittings (BarbLock® system). The two parts of the fitting, slid onto each other, compress the hose around its entire circumference (360°), ensuring complete tightness of the connection, while providing a smooth, stepless transition between the hose's inner surface and the inside of the fitting's tail (Smooth Inner Bore). This eliminates turbulence and dead spaces – areas of flow stagnation that could become sites of bacterial growth. The use of Pure-Fit® fittings secured with Pure-Fit®/Barblock® fittings ensures significantly better tightness and hygienic properties of the connection compared to assembly with clamps. Sterilization: radiation (PP) or radiation and autoclave (PVDF). Material: polypropylene (PP) or PVDF. Hardness: 85 Shore (A) (PP) or 78 Shore (A) (PVDF). Working pressure: 17 bar (20°C), 7 bar (93°C). Operating temperature: up to 93°C (PP) or up to 135°C (PVDF).
        • Small-diameter plastic hose for cleaning sewers JCL
          Select options This product has multiple variants. The options may be chosen on the product page / Details

          Small-diameter plastic hose for cleaning sewers JCL

          All products | Hoses and fittings for sewage
          0 €
          Flexible, kink-resistant small-diameter hose designed for pressure cleaning of industrial and domestic sewer systems with water. Especially recommended for use in environments with high humidity and high salt concentration. Safety factor 2.5:1. Inner layer: thermoplastic polymer. Reinforcement: high-strength braids. Outer layer: black polyurethane, abrasion resistant. Working pressure: 345 bar. Operating temperature: from -40°C to +70°C.
        • Handle for water nozzle, brass, stainless steel, AKBO Water Saving
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          Handle for the AKBO Water Saving spray gun, with 1/2" BSP female thread on both sides. Made of brass or AISI 304 steel, coated with blue EPDM rubber. Material: brass or AISI 304 steel. Working pressure: up to 16 bar. Operating temperature: up to +80°C.
        • Universal antibacterial hose VERSILON™ SILVER
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          Flexible, highly hygienic hose with a phthalate-free inner layer that also inhibits the growth of all types of microorganisms: bacteria, fungi and algae. The special polymer additive AlphaSan ® (a silver-containing ceramic ion-exchange resin based on zirconium phosphate) prevents microbial growth and the formation of mould and biofilm. Silver plays a significant role in the inhibitor's action and is hygienically safe. VERSILON™ SILVER hose is used in water purification, ice machines, chemical transfer and other industrial applications, preventing product contamination, biological corrosion and unpleasant odours. Meets FDA and NSF-51 requirements and does not discolour during use. Pressure safety factor 5:1. Installed on hose tails and fittings using bands and clamps. The maximum working pressure is specified at 23°C. Material: PVC (special). Working temperature: up to +74°C. Brittleness temperature: -35°C. Hardness: 69 Shore (A). Density: 1.21 g/cm³. Note: Product prepared and packaged in the Tubes International CLEAN ROOM in compliance with strict cleanliness standards. This product is non-returnable.
        • Universal hose for peristaltic pumps VERSILON™ TR-1055
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          A hose made of a special EPDM rubber compound for use in peristaltic pumps. Chemically resistant, resistant to UV radiation, ozone and abrasion, with excellent bending fatigue resistance, it provides a long service life (over 1000 h) and maintains constant flow during operation in the pump. Used for dosing soap, cleaning and disinfecting agents, alkaline chemical substances, in laundries, dishwashing facilities, for wastewater discharge, for brake fluids and a number of other substances. Compliant with RoHS 2011/65/EU. Pressure safety factor 5:1. Mounted on nipples and fittings using clamps and bands. Maximum working pressure is given for a temperature of 23°C. Material: EPDM rubber (special). Operating temperature: from -60°C to +121°C. Hardness: 55 Shore (A). Density: 1.11 g/cm³. Note: Product packed in the Tubes International CLEAN ROOM Clean Zone under strict cleanliness standards. Product is non-returnable.
        • O-ring seal for quick coupling plug, series TST 100.12
          Select options This product has multiple variants. The options may be chosen on the product page / Details

          O-ring seal for quick coupling plug, series TST 100.08

          All products | Quick couplings for injection molds
          0 €
          O-ring seal intended for the quick coupling plug. Series: TST 100.08. Working pressure: 10 bar. Material: NBR or viton. Operating temperature: from -20°C to +100°C – NBR or from -15°C to +200°C – viton.
        • O-ring seal for quick coupling plug, series TST 100.12
          Select options This product has multiple variants. The options may be chosen on the product page / Details

          O-ring seal for quick coupling plug, series TST 100.12

          All products | Quick couplings for injection molds
          0 €
          O-ring seal designed for the quick coupling plug. Series: TST 100.12. Working pressure: 10 bar. Material: NBR or viton. Operating temperature: from -20°C to +100°C - NBR or from -15°C to +200°C - viton.
        • Multilayer helically corrugated steel hose for high pressures and vibration damping BOA DUO®
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          Hoses available only as complete hose assemblies with fittings crimped by Tubes International. For an individual quotation, use the enquiry form in the shop or download the hose assembly selection form (available as an attachment), complete it and send it to: sklep@tubes-international.com Special high-pressure steel hose with a double wall and helical corrugations produced by cold forming and electric welding using a process patented in Switzerland. Corrugated steel strip is wound helically and resistance-welded at the corrugation crest of the tube. The double wall, which becomes a triple wall at the corrugation crest, provides exceptional strength and service life while maintaining high flexibility and a small bending radius. Depending on the reinforcement version, the hose has one or more high-strength stainless steel braids; it is also available without braid. Safety factor 4:1. The hose also provides excellent vibration damping, preventing vibration transmission between equipment. Meets ISO 10380 requirements. Designed for liquids and gases in high-pressure applications and for all types of piping systems under demanding operating conditions. Used with engines, pumps and compressors, as a universal vibration damper and in high-pressure gas systems, among other applications. The available UHP version (DN5 and DN6), with increased working pressure, is intended particularly for hose assemblies for filling high-pressure gas cylinders. Inner layer: corrugated AISI 316Ti steel hose (UHP version – AISI 316L). Reinforcement: single or double AISI 304 steel braid. Working temperature: from -273°C to +600°C (working pressure depends on temperature).
        • Plug 45° quick coupling with a thread internal NPT, series TST 100.08, brass nickel-plated
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          45° quick coupling plug with BSP female thread, without valve, used in industry for cooling injection and casting moulds for plastic and aluminium parts, for transferring hot oil. Series: TST 100.08. Working pressure: 10 bar. Operating temperature: from -20°C to +100°C (NBR). Material: nickel-plated brass (connector, sleeve and plug), stainless steel (spring, ring, balls).
        • Plug 45° quick coupling with a thread internal NPT, series TST 100.12, brass nickel-plated
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          45° quick coupling plug with BSP female thread, without valve, used in industry for cooling injection molds and die-cast parts made of plastics and aluminum, for conveying hot oil. Series: TST 100.12. Working pressure: 10 bar. Operating temperature: from -20°C to +100°C (NBR). Material: nickel-plated brass (connection, sleeve and plug), stainless steel (spring, ring, balls).
        • Plug 45° quick coupling with a thread internal NPT, series TST 100.08, brass nickel-plated
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          45° plug of quick coupling with NPT female thread, without valve, used in industry for cooling injection moulds and die-cast parts made of plastics and aluminium, for transferring hot oil. Series: TST 100.08. Working pressure: 10 bar. Operating temperature: from -20°C to +100°C (NBR). Material: nickel-plated brass (connection, sleeve and plug), stainless steel (spring, ring, balls).
        • Plug 45° quick coupling with a thread internal NPT, series TST 100.12, brass nickel-plated
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          45° quick coupling plug with NPT female thread, without valve, used in industry for cooling injection molds and die-cast parts made of plastics and aluminum, for conveying hot oil. Series: TST 100.12. Working pressure: 10 bar. Operating temperature: from -20°C to +100°C (NBR). Material: nickel-plated brass (connector, sleeve and plug), stainless steel (spring, ring, balls).
        • Plug 45° quick coupling with fitting for hose PUSH-ON, series TST 100.08, brass nickel-plated
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          45° quick coupling plug with PUSH-ON hose fitting, without valve, used in industry for cooling injection and casting molds for plastic and aluminium parts, for hot oil transfer. Series: TST 100.08. Working pressure: 10 bar. Operating temperature: from -20°C to +100°C (NBR). Material: nickel-plated brass (connector, sleeve and plug), stainless steel (spring, ring, balls).
        • Plug 45° quick coupling with fitting for hose PUSH-ON, series TST 100.12, brass nickel-plated
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          45° quick coupling plug with PUSH-ON hose tail, without valve, used in industry for cooling injection and casting moulds for plastic and aluminium parts, for transferring hot oil. Series: TST 100.12. Working pressure: 10 bar. Operating temperature: from -20°C to +100°C (NBR). Material: nickel-plated brass (connector, sleeve and plug), stainless steel (spring, ring, balls).
        • Plug 90° DN 13 quick coupling with a thread external metric, without valve, series TST 190, brass
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          90° DN 13 quick coupling plug with BSPT male thread, DIN 2999, without valve. Widely used in industry for cooling injection molds and die-cast parts made of plastics, aluminum, brass and zinc alloys. Can be used for water in cleaning machines, for hot oil, steam. Series: TST 190. Working pressure: 25 bar. Material: brass. Operating temperature: from -20°C to +200°C.
        • Plug 90° DN 13 quick coupling with a thread external metric, without valve, series TST 190, brass
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          90° plug DN 13 of quick coupling with DIN 158 tapered metric male thread, without valve. Widely used in industry for cooling injection moulds and die-cast parts made of plastics, aluminium, brass and zinc alloys. Can be used for water in cleaning machines, for hot oil, water vapour. Series: TST 190. Working pressure: 25 bar. Material: brass. Operating temperature: from -20°C to +200°C.
        • Plug 90° DN 6 quick coupling with a thread external BSPT, without valve, series TST 6, brass
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          90° DN 6 quick coupling plug with BSPT male thread, without valve. Widely used in industry for cooling injection molds and die-cast parts made of plastics, aluminum, brass and zinc alloys. Can be used for water in cleaning machines, for hot oil, steam. Series: TST 6. Working pressure: 10 bar. Material: brass. Operating temperature: from -20°C to +200°C.
        • Plug 90° DN 6 quick coupling with a metric thread external, without valve, series TST 6, brass
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          90° DN 6 quick coupling plug with metric male thread, without valve. Widely used in industry for cooling injection and casting molds for plastic, aluminium, brass and zinc alloy parts. Can be used for water in cleaning machines, for hot oil, steam. Series: TST 6. Working pressure: 10 bar. Material: brass. Operating temperature: from -20°C to +200°C.
        • Plug 90° DN 9 quick coupling with a thread external metric, without valve, series TST 090, brass
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          90° DN 9 quick coupling plug with BSPT male thread, DIN 2999, without valve. Widely used in industry for cooling injection and casting moulds for plastic, aluminium, brass and zinc alloy parts. Can be used for water in cleaning machines, for hot oil, steam. Series: TST 090. Working pressure: 25 bar. Material: brass. Operating temperature: from -20°C to +200°C.
        • Plug 90° DN 9 quick coupling with a thread external BSPT, without valve, series TST 9, brass
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          90° DN 9 quick coupling plug with BSPT male thread, without valve. Widely used in industry for cooling injection molds and die-cast parts made of plastics, aluminum, brass and zinc alloys. Can be used for water in cleaning machines, for hot oil, steam. Series: TST 9. Working pressure: 15 bar. Material: brass. Operating temperature: from -20°C to +200°C.
        • Plug 90° DN 9 quick coupling with a thread external metric, without valve, series TST 090, brass
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          90° plug DN 9 of quick coupling with DIN 158 tapered metric male thread, without valve. Widely used in industry for cooling injection moulds and die-cast parts made of plastics, aluminium, brass and zinc alloys. Can be used for water in cleaning machines, for hot oil, water vapour. Series: TST 090. Working pressure: 25 bar. Material: brass. Operating temperature: from -20°C to +200°C.
        • Plug 90° quick coupling with a thread internal NPT, series TST 100.08, brass nickel-plated
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          90° quick coupling plug with BSP female thread, without valve, used in industry for cooling injection molds and die-cast parts made of plastics and aluminum, for conveying hot oil. Series: TST 100.08. Working pressure: 10 bar. Operating temperature: from -20°C to +100°C (NBR). Material: nickel-plated brass (connector, sleeve and plug), stainless steel (spring, ring, balls).
        • Plug 90° quick coupling with a thread internal NPT, series TST 100.12, brass nickel-plated
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          90° quick coupling plug with BSP female thread, without valve, used in industry for cooling injection and casting molds for plastic and aluminium parts, for hot oil transfer. Series: TST 100.12. Working pressure: 10 bar. Operating temperature: from -20°C to +100°C (NBR). Material: nickel-plated brass (connector, sleeve and plug), stainless steel (spring, ring, balls).
        • Plug 90° quick coupling with a thread internal NPT, series TST 100.08, brass nickel-plated
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          90° quick coupling plug with NPT female thread, without valve, used in industry for cooling injection and casting moulds for plastic and aluminium parts, for transferring hot oil. Series: TST 100.08. Working pressure: 10 bar. Operating temperature: from -20°C to +100°C (NBR). Material: nickel-plated brass (connector, sleeve and plug), stainless steel (spring, ring, balls).
        • Plug 90° quick coupling with a thread internal NPT, series TST 100.12, brass nickel-plated
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          90° quick coupling plug with NPT female thread, without valve, used in industry for cooling injection molds and die-cast parts made of plastics and aluminum, for conveying hot oil. Series: TST 100.12. Working pressure: 10 bar. Operating temperature: from -20°C to +100°C (NBR). Material: nickel-plated brass (connection, sleeve and plug), stainless steel (spring, ring, balls).
        • Plug 90° quick coupling with fitting for hose PUSH-ON, series TST 100.08, brass nickel-plated
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          90° plug of quick coupling with PUSH-ON hose tail, without valve, used in industry for cooling injection moulds and die-cast parts made of plastics and aluminium, for transferring hot oil. Series: TST 100.08. Working pressure: 10 bar. Operating temperature: from -20°C to +100°C (NBR). Material: nickel-plated brass (connection, sleeve and plug), stainless steel (spring, ring, balls).
        • Plug 90° quick coupling with fitting for hose PUSH-ON, series TST 100.12, brass nickel-plated
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          90° quick coupling plug with PUSH-ON hose tail, without valve, used in industry for cooling injection molds and die-cast parts made of plastics and aluminum, for conveying hot oil. Series: TST 100.12. Working pressure: 10 bar. Operating temperature: from -20°C to +100°C (NBR). Material: nickel-plated brass (connector, sleeve and plug), stainless steel (spring, ring, balls).
        • Plug DN 13 quick coupling with fitting for hose PUSH-ON, without valve, series TST 190, brass
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          DN 13 quick coupling plug with PUSH-ON hose tail, without valve. Widely used in industry for cooling injection and casting moulds for plastic, aluminium, brass and zinc alloy parts. Can be used for water in cleaning machines, for hot oil, steam. Series: TST 190. Working pressure: 25 bar. Material: brass. Operating temperature: from -20°C to +200°C.
        Go to Top