How do I install the 90° Coolant Round Nozzle, 1/4" System, JETON for optimal coolant flow and positioning?

How to install the 90° Coolant Round Nozzle, 1/4" System, JETON for optimal coolant flow and positioning: 1. Prepare the system: depressurize and clean the coolant line. Verify compatibility with the 1/4" system fittings and that working pressure will not exceed 3 bar. 2. Mount the nozzle: push the 90° Coolant Round Nozzle, 1/4" System, JETON firmly into the 1/4" hose or connector until fully seated. If using threaded or push-fit adapters, tighten by hand and then a quarter turn with pliers if needed—do not overtighten to avoid damaging the acetal body. 3. Position for precision: orient the 90° nozzle so the round outlet points directly at the cutting zone or tool tip. Use the compact 90° angle to fit into tight spaces; adjust the nozzle rotation until the coolant stream hits the intended target. 4. Optimize flow: choose the nozzle size (1/16", 1/8", or 1/4") that matches your required jet diameter and flow rate. Larger sizes deliver more coolant; smaller sizes give a more focused stream. Set system pressure up to the recommended 3 bar to achieve the desired spray pattern without misting. 5. Secure and test: ensure the nozzle is stable and the hose has strain relief to prevent movement. Restore pressure and run the machine at intended speed. Observe coolant coverage on the tool and workpiece; fine-tune nozzle angle, rotation, or swap nozzle size if necessary. 6. Maintenance: periodically inspect the acetal nozzle for wear or clogging and clean or replace as needed. Keep operating temperature below +65°C. Following these steps ensures precise coolant delivery, improved tool life, and reliable performance with the 90° Coolant Round Nozzle, 1/4" System, JETON.

Can the 90° Coolant Round Nozzle, 1/4" System, JETON withstand continuous operation at 3 bar and +65°C without performance loss or material deformation?

Yes. The 90° Coolant Round Nozzle, 1/4" System, JETON is specified for continuous operation up to 3 bar and temperatures up to +65°C. Made from durable acetal with high wear resistance and long-term dimensional stability, it is designed to maintain coolant flow direction and mechanical integrity under those exact conditions. Therefore, when used within the stated limits (≤3 bar and ≤+65°C), it will operate continuously without performance loss or material deformation.

Nozzle 90° round for coolant, system 1/4″, JETON

Air and water hoses, All products/

Additional information

Nozzle 90° round for hoses for coolant JETON – system 1/4″. Available in sizes 1/16″, 1/8″ and 1/4″. Material: acetal. Working pressure: up to 3 bar. Operating temperature: up to +65°C.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
JT-82223	Nozzle 90° 1/16" (system 1/4")	-	3	In stock	Enquiry
JT-82224	Nozzle 90° 1/8" (system 1/4")	-	3	In stock	Enquiry
JT-82225	Nozzle 90° 1/4" (system 1/4")	-	3	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +91 8 925 918 796 or email us: chennai@tubes-international.com

SEND ENQUIRY

Nozzle 90° round for hoses for coolant JETON – system 1/4″. Available in sizes 1/16″, 1/8″ and 1/4″. Material: acetal. Working pressure: up to 3 bar. Operating temperature: up to +65°C.