- Home
- All products
Our products
Product categories
Working pressure [bar]
Minimum operating temperature [°C]
Maximum operating temperature [°C]
Material
Vacuum resistance
Standard length [m]
Select options This product has multiple variants. The options may be chosen on the product page / DetailsCoupling push-in angled 90° of couplings push-in for hose o diameter inch, series S, type PULC. economical solution for connecting flexible hoses pneumatic o inch calibrated diameter outer. easy and fast in use. Material: plastic plastic. Working pressure: 10 bar. Vacuum: 0.99 bar. Operating temperature: od 0°C up to +60°C. sealing: NBR.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsAdapter - plug high-pressure with thread external BSP (sealing 60° cone), type A113. Material: steel carbon, galvanized.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsAdapter with thread external BSP (sealing on cone internal 60°) and thread external BSPT (sealing on cone external 120°) enabling connection quick couplings and hoses UHP of each other, a also connection ich for blocks connection UHP. Material: steel galvanized on black. Working pressure: 2500 bar.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsFilter FIL series NEW DEAL recommended for decentralised compressed-air systems or in the immediate vicinity of actuating devices. Thanks to its construction (metal construction) it is characterised by resistance to heavy-duty operating conditions. Intended for use at higher pressures. Size: 1/4", 3/8", 1/2", 3/4", 1". Filtration grade: 4 µm, 20 µm, 50 µm. Supply pressure: up to 18 bar, for trigger RA up to 10 bar. Operating temperature: up to +50°C. Connection: 1/4" BSP female, 3/8", 1/2", 3/4", 1". Condensate drain: manual / semi-automatic (RMSA), automatic (SAC). Flow rate: 1700 l/min - 1/4", 4100 l/min - 3/8", 1/2", 11000 l/min - 3/4", 1" (at an inlet pressure of 6 bar Δp = 1 bar).
Select options This product has multiple variants. The options may be chosen on the product page / DetailsWrench disassembly serving for detachable hoses od lines push-in. intended for series R and RL (FOX). Diameter outer hose od 3 for 10 mm.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsElbow 90° (R = 1.5 x d) KSBB 45 intended for quick and efficient assembly of ducting hoses using BC worm-drive bridge clamps. Material: steel galvanized.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsA crimped BANJO fitting for PTFE brake hoses. Material: carbon steel, chrome-plated.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsA blade spare for shears PZP12 (ZC-PZP12).
Select options This product has multiple variants. The options may be chosen on the product page / DetailsPump hydraulic MPT100 o drive manual Intended for crimpers for air conditioning type TNT250/B. height: 315 mm.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsFerrule AF-THU for hoses PTFE type HYPERLINE SB, FX, V. Diameter D1 - Diameter outer. Diameter D2 - Diameter inner. Diameter D3 - Diameter lock. Material: steel AISI 304.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsA flat IBC gasket for a flange PN made acc. to standards PN-EN 1514-1. The permissible pressure working, at which can be used a given gasket depends od temperatures and kinds medium (selection should agree with TUBES INTERNATIONAL®). at selecting the gasket should pay attention on dimension diameter outer, appropriate for class flange. For example: a gasket DN 10 PN40 is suitable for class PN10, PN16 and PN25. Material: EPDM. Working pressure: up to 60 bar. Operating temperature: od -30°C up to +120°C.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, flexible hose intended for discharge dusts, sawdust, chips, light bulk materials o properties abrasive. used in industry wood, construction, food. resistant to ozone. Wall thickness measured between the spiral. available other diameter in the scope 30 ÷ 400 mm. Hose material: transparent polyurethane. Reinforcement: copper-plated spiral with wire steel. Operating temperature: od -40°C up to +90°C.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose suction- delivery for pneumatic conveying dry substances abrasive. thick Layer inner with polyurethane, o very high resistance to abrasion (below 36 mm 3 acc. to DIN 53516), very smooth and o low factor friction, enabling sliding conveyed product. built-in two cable copper, which po earthing (connection with earthed fitting) discharge charges electrical. Layer outer corrugated, with black, antistatic (R 6 Ω) rubber SBR / NR resistant to abrasion, ozone and aging. hose intended for conveying dry strong abrasive substances, in particular in smelters, foundries, welding shops, industry ceramic, construction and wood. assembly: hose intended for mounting system GHIBLI - aluminum half-flanges PN10 applied externally on hose. Inner layer: special polyurethane (PU). Reinforcement: cord synthetic, steel spiral. Outer layer: black rubber SBR/NR. Working pressure: from 3 bar to 10 bar - depending on the diameter hose. Vacuum: 0.9 bar. Operating temperature: od -30°C up to +80°C (momentarily for +100?C).
Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, flexible hose intended for solvents, paints, isocyanate, polyol, gases, air, liquids based on water. Inner layer: polyamide. Reinforcement: an aramid braid + a steel braid. Outer layer: micro-perforated polyurethane. Operating temperature: od -40°C up to +93°C (for water and air up to +65°C).
Select options This product has multiple variants. The options may be chosen on the product page / DetailsSocket cap coupling CAMLOCK DP made in accordance with the American military standard MIL-C-27487 (A-A-59326). Working pressure: up to 7 bar, depending on the coupling size. Material: polypropylene glass-fiber-reinforced.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsCap STORZ, fitted with a chain protecting against loss, Intended for installation transfer for liquid and bulk substances. used in firefighting, systems irrigation, industry chemical, food, agriculture etc. O symmetrical construction parts connection, thanks to this in straight way combines je of each other. connect can element o the same spacing lugs. Material: steel stainless. Working pressure: 16 bar. Gasket: Viton.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsStraight valve foot with cover protective and sockets in plane face, serves for control foot through the operator devices in systems pneumatics. Connection: 1/4". Working pressure: from 2.5 bar to 10 bar. Operating temperature: -10°C up to +60°C. Flow rate nominal: 840 l/min (at an inlet pressure of 6 bar Δp = 1 bar).
Select options This product has multiple variants. The options may be chosen on the product page / DetailsCoupling bulkhead straight JIC 37° with thread external UNF (sealing on cone external 37°). Material: steel AISI 316.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsCoupling Tee type LET-LOK® for a metric tube Intended mainly for industry chemical, petrochemical, pharmaceutical, power generation, nuclear power plants and process engineering. The permissible pressure working specifies on the basis of diameter outer and wall thickness wall tubes (details in the attachment). Material: steel AISI 316.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-pressure 90° adapter type A114C with thread external BSP (sealing 60° cone) and with thread internal BSP, with a nut swivel (sealing 60° cone), version "compact". Material: steel AISI 316L.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsScrew fitting with thread internal, type FACR, for hoses brake PTFE. Material: carbon steel, chrome-plated.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsBody elbow BANJO, type R28, for bolts series D, intended for connections lines and other element in systems pneumatic. easy and fast in use for repeated mounting without loss tightness po side mechanical and pneumatic. Material: plastic plastic. Working pressure: 12 bar. medium working: vacuum, air. Operating temperature: od -20°C up to +60°C. sealing: NBR.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsFitting tubular metric type LET-LOK® with thread external BSP intended mainly for industry chemical, petrochemical, pharmaceutical, power generation, nuclear power plants and process engineering. The permissible pressure working specifies on the basis of diameter outer and wall thickness wall tubes (details in the attachment). Material: steel AISI 316.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsTee "T" type cube with thread internal enabling connection quick couplings and hoses UHP of each other. Material: steel carbon, galvanized on black. Working pressure: 700 bar (at factor safety 4), 1000 bar (at factor safety 2.8).
Select options This product has multiple variants. The options may be chosen on the product page / DetailsSymmetrical "Y" tee KTSBY intended for quick and efficient assembly of ducting hoses using BC worm-drive bridge clamps. Material: steel galvanized.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, very flexible and pliable, resistant chemical hose intended for discharge aggressive chemical vapours, gases, dusts and fibres. used mainly in industry chemical and m.in. at removal asbestos. very good resistance chemical on solvents and other aggressive vapours. resistant to hydrolysis and corrosion biological. Contains no halogen compounds or plasticisers. is characterized high compressibility - for 1:8, strong design, resistance on impacts thanks to outer spiral. Also available with a stainless steel spiral (from 80 mm diameter). Assembly of the hose on connectors with bridge clamps (lewo-handed). Checking chemical resistance - the chemical resistance table for polyethylene (preliminary selection), confirmation of resistance and conditions of use - by Tubes International. length standard: od 2 for 10 m. Hose material: fabric polyethylene coated polyethylene (PE). Reinforcement: outer spiral with wire and sheet steel galvanized. Operating temperature: od -40°C up to +80°C.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, flexible hose intended for oil installation hydraulic, gases, air, fuels, liquids based on water. resistant to very low temperatures and heavy conditions atmospheric. standards: SAE 100R18, ISO 3949-R18. Inner layer: polyester. Reinforcement: one or two synthetic braids. Outer layer: micro-perforated polyurethane. Working pressure: 210 bar. Operating temperature: od -55°C up to +100°C (for water and air up to +70°C).
Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose delivery for pneumatic conveying dry substances abrasive. special The design hose o exceptional resistance to abrasion. Layer inner smooth, with black antistatic rubber natural with embedded in it balls with corundum (Al 2 O 3 – oxide aluminum), material ceramic o high hardness. built-in cable copper, which po earthing (connection with earthed fitting) discharges charges electrical. Layer outer with black, antistatic (R 6 Ω) rubber SBR / NR resistant to abrasion and aging. hose intended for conveying dry strong abrasive substances: e.g. dry cement, carbon, dust carbon, coke, solid fuels with raw materials secondary, minerals, powders ceramic, shot steel, fragments glass, fibre glass. used in smelters, coking plants, power plants, cement plants, mines, smelters glass, factories materials abrasive and materials insulating. advantage is large service life hose in these use – traditional hose with rubber resistant to abrasion can work e.g. only several dni, a hose ALUSPHERE in these same conditions even several months. Inner layer: balls ceramic embedded in black rubber NR. Reinforcement: cord synthetic. Outer layer: black rubber SBR/NR. Working pressure: 12 bar. Operating temperature: od -30°C up to +80°C.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsPlug coupling CAMLOCK AR (reducing) with a thread internal BSP made in accordance with the American military standard MIL-C-27487 (A-A-59326), commonly used as a transfer coupling, especially in the petrochemical industry. Working pressure: up to 10 bar. Material: aluminum.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsValve reducing REG, series SYNTESI®, with end connections 1/8" ÷ 1", serves for regulation pressure working and maintaining go on fixed level, ensuring correct operation, in connected za nim installation, independently od changing sie wear medium. W a valve used instead of diaphragm flat, diaphragm shaped, which ensures greater value flow nominal thanks to greater surge diaphragm, as well as greater sensitivity and speed reaction on change setting, through reduction friction static and kinetic components and greater accuracy in maintaining set pressure output at change value flow and pressure supply. W case rise pressure output over value setting diaphragm opens valve trigger and vents reducer until for obtaining value pressure compliant with setting. mechanism type „push-lock” allows on locking a knob in any position through its pressing. Plate locking allows mounting padlock protective against unauthorised change setting pressure output. additional the connection with the front and with the back, can be used for connection pressure gauge, relay pneumo-electric or fittings push-in. drawn with these connections air is reduced. Size: SY1, SY2. Output pressure range: 0÷2, 0÷4, 0÷8, 0÷12 bar. Supply pressure: up to 15 bar, depending on size. Operating temperature: od -10°C up to +50°C. Connection: 1/8" BSP female ÷ 1". Additional connection for a pressure gauge or fittings: 1/8" BSP female for size SY1, 1/4" BSP female for size SY2. Flow rate: 1200 l/min - 1/8", 2800 l/min - 1/4", 3350 l/min - 3/8" (SY1), 5300 l/min - 3/8" (SY2), 7400 l/min - 1/2", 7600 l/min - 3/4" and 1" (at an inlet pressure of 6 bar Δp = 1 bar).
Select options This product has multiple variants. The options may be chosen on the product page / DetailsSet for connections flange (EN 1092), type SZ1. W set: screws DIN931 - 4 pcsi, a nut DIN934 - 4 pcsi and washer DIN125A - 4 pcsi. Class properties mechanical: A2-70 - screws; A2-70 - nuts. Selection of bolts and nuts for flanges according to the table in the attachment. Material: steel AISI 304.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsAdapter - Tee high-pressure type A109 with thread external 3 x BSP (sealing 60° cone). Material: steel carbon, galvanized.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsAdapter with thread external BSP (sealing on cone external 120°) and thread external BSP (sealing on cone external 120°) enabling connection quick couplings and hoses UHP of each other, a also connection ich for blocks connection UHP. Material: steel galvanized on black. Working pressure: 3000 bar.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsFilter with reducer (filter-regulator) FR, series SKILLAIR®, is a device consisting of a filter and a reducing valve. It reduces and purifies the air supplied by the compressor. Size: 300. range pressure output: 0÷2, 0÷4, 0÷8, 0÷12 bar. Supply pressure: up to 13 bar, depending on kinds trigger. Operating temperature: up to +50°C. Connection: 1/2" BSP female ÷ 1". Pressure gauge connection: 1/8" BSP female. Condensate drain: manual / semi-automatic (RMSA), automatic (RA, SAC). Flow rate: 5600 l/min at an inlet pressure of 6 bar Δp = 1 bar).
Select options This product has multiple variants. The options may be chosen on the product page / DetailsSocket double coupling CAMLOCK DD made in accordance with the American military standard MIL-C-27487 (A-A-59326). commonly used as a transfer coupling, especially in the petrochemical industry. Working pressure: up to 10 bar, depending on the size coupling. Material: aluminum. Levers: steel AISI 304 (in sizes 1.1/4" for 4" - Levers made of brass). Sealing: NBR.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsComplete Tee plug-in BANJO, double, type R57, intended for connections lines and other element in systems pneumatic. easy and fast in use for repeated mounting without loss tightness po side mechanical and pneumatic. Material: brass nickel-plated. Working pressure: 16 bar. medium working: vacuum, air. Operating temperature: od -20°C up to +80°C. sealing: NBR.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsA straight tubular crimped fitting, type EP, for PTFE brake hoses. Material: carbon steel, chrome-plated.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsA flat IBC gasket for a flange ASA made acc. to standards ASME B16.21 (ANSI). The permissible pressure working, at which can be used a given gasket depends od temperatures and kinds medium (selection should agree with TUBES INTERNATIONAL®). at selecting the gasket should pay attention on dimension diameter outer, appropriate for class flange. For example: a gasket DN 15 ASA600 is suitable for class ASA300 and ASA400. Material: KLINGER SIL 4430. Working pressure: up to 100 bar. Operating temperature: od -200°C up to +400°C.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery light and extremely pliable hose rubber, for extraction dusts, powders and other lightly abrasive materials. Layer inner smooth, with abrasion-resistant rubber o wall thickness 2.4 mm. Layer outer corrugated, resistant to abrasion and conditions atmospheric. thanks to reinforcement spiral steel resistant to kinking and vacuum for 0.6 bar. Not is intended for use with overpressure, designed only for vacuum (extraction). Due to lightness and exceptional as on hose rubber flexible perfectly works in systems vacuum cleaning in industry, on example in quarries or smelters. It has a copper anti-electrostatic wire for discharging electric charges. Inner layer: black rubber natural. Reinforcement: cord synthetic, steel spiral. Outer layer: black rubber SBR. Vacuum: for 0.6 bar. Operating temperature: od -40°C up to +70°C.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose polyurethane, reinforced spiral with wire steel, intended for discharge and conveying bulk materials, dusts and sawdust. resistant to ozone. Hose material: transparent polyurethane. Reinforcement: spiral with galvanized wire steel. Operating temperature: od -40°C up to +90°C.



















































