- Home
- Devices and accessories
- Air guns
Our products
Select options This product has multiple variants. The options may be chosen on the product page / DetailsNozzle BLOWSTAR with double a nipple for guns for air, terminated thread metric M12x1.25. is characterized low level noise - only 74 dB at a pressure of 6 bar, not weakening force air blowing. meets the following standards safety and the directive: OSHA 1-13.1. (European Agency safety and Health in use), 2003/10/WE, 2006/42/WE, EN 12100. Flow rate nominal: 295 l/min at a pressure of 6 bar. Material: cast zinc (nozzle), aluminum (nipple).
Select options This product has multiple variants. The options may be chosen on the product page / DetailsA fitting rubber for nozzle o diameter outer 6 mm (compatible with nozzle under index EW-470K12), protecting against scratches cleaned delicate surfaces. Material: TPU.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsNozzle extended bent o diameter hole 3 mm for guns for air, terminated thread metric M12x1.25. Diameter tubes: 5 mm. available length: 110 mm, 160 mm and 260 mm. Material: brass nickel-plated. maximum pressure: 10 bar. Operating temperature: od -10°C up to +50°C.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsNozzle standard bent, for installation directly for body gun. length nozzle: 90 mm. Working pressure: 16 bar.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsHandy Feather for compressed air, intended for fast removing with surface all contaminants: liquids, fine chips, filings etc. made with anodized aluminum. equipped in nozzle with the possibility regulating flow one hand - od narrow for wide stream air. rubber a nozzle on the tip feather protects surfaces against scratching. terminated a plug EUROSTANDARD 7.2. Material: housing – aluminum protected method anodized; sealing – NBR. Diameter hole nozzle: 0 ÷ 3 mm. Flow rate nominal: 300 l/min at a pressure of 6 bar. pressure maximum: 12 bar. pressure operating: 1 ÷ 6 bar. Operating temperature: od -10°C up to +60°C.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsHandy nozzle straight for compressed air with a lever, Intended for removing with surface all contaminants: liquids, fine chips, filings etc. The design lever reduces fatigue and discomfort the operator, even during longer use. equipped in standard nozzle o diameter hole 2 mm. depending on the connection we distinguish nozzle ending in fitting for hose o diameter 6 mm and 9 mm or a plug EUROSTANDARD 7.2. Material: aluminum. Diameter hole nozzle: 2 mm. pressure maximum: 8 bar. pressure operating: 1 ÷ 6 bar. Operating temperature: od -10°C up to +50°C.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsNozzle standard with central a hole (available diameter hole 1.5 mm and 2 mm), is characterized concentrated a stream air o high force air blowing. level noise 90 dB at pressure above 4 bar. Connection: M12x1.25 male. Material: aluminum. pressure maximum: 10 bar. Operating temperature: od -10°C up to +50°C.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsNozzle injector FULL-JET o diameter hole 2.5 mm with wide a stream air, sucks in air with ambient at exceptionally high flow, increasing Flow rate air twice. level noise: 90 dB. Material: aluminum. pressure operating: 2 ÷ 8 bar. Operating temperature: od -10°C up to +50°C.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsNozzle injector FULL-JET o diameter hole 2 mm with wide a stream air, sucks in air with ambient at exceptionally high flow, increasing Flow rate air twice. level noise: 90 dB. Material: black plastic. pressure operating: 2 ÷ 8 bar. Operating temperature: od -10°C up to +50°C.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsNozzle injector; for direct installation on tube; sucks in air with ambient at exceptionally high flow, increasing Flow rate air twice. Compliant with the OSHA 1-13.1 standard. (European Agency safety and Health in use). Working pressure: 16 bar.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsNozzle with a screen air protecting the operator against particles contaminants in during performing operations and dampens noise. level noise 80 dB at a pressure of 6 bar. Diameter hole nozzle 1.5 mm. Material: aluminum. pressure maximum: 10 bar. Operating temperature: od -10°C up to +50°C.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsNozzle with reduction noise with thread internal for gun CEJN; Intended for use in small space; for direct installation on tube. Sound level below 85 dB, in accordance with the European Machinery Directive art. 1.5.8. Compliant with the OSHA 1-13.1 standard. (European Agency safety and Health in use). Working pressure: 16 bar.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsNozzle with reducer noise; for direct installation on tube; level sound 82 dB, in accordance with European the directive machinery art. 1.5.8. Compliant with the OSHA 1-13.1 standard. (European Agency safety and Health in use). Working pressure: 16 bar.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsNozzle with an insert dampening is characterized wide a stream air, low force air blowing and extremely low level noise - 70 dB. Connection: M12x1.25 male. Material: aluminum. pressure maximum: 10 bar. Operating temperature: od -10°C up to +50°C.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsScreen protective Ø70 mm to durable A guard with polyethylene, which protects the operator against debris, which appear often at blowing out chips with machined element. perfectly is suitable also for prevents spreading coolant during drying parts. fully similar function co nozzle with a screen air (EW-269K27). assembly between nozzle a gun (can use nozzles short and extended, tzw. „tube”). Material: polyethylene. Operating temperature: od -10°C up to +50°C.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh quality aluminum Gun for compressed air, intended for removing with surface all contaminants: liquids, fine chips, filings etc. regulation flow degree press lever. made with forged aluminum, protected anodizing ensures high strength, durability and resistance corrosion. ideal works even in difficult conditions use. Gun equipped is in nozzle FULL-JET o diameter 2.5 mm, replaceable, with thread connection external M12x1.25, which is characterized significantly wider a stream air and greater power operation at a pressure of 2 bar, in comparison for standard nozzle o diameter hole 1.5 mm. instead of nozzle FULL-JET install can other nozzles – see accessories for guns EWO. depending on the connection we distinguish Gun terminated a plug EUROSTANDARD 7.2 or fitting for hose o diameter 6 mm, 9 mm and 13 mm. Material: aluminum (forging). Diameter hole nozzle: 2.5 mm. pressure operating: 2 ÷ 8 bar. Operating temperature: od -10°C up to +50°C.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh quality aluminum Gun for compressed air, intended for removing with surface all contaminants: liquids, fine chips, filings etc. regulation flow degree press lever. equipped in valve reducing pressure for regulation maximum flow appropriate for use. made with forged aluminum, protected anodizing ensures high strength, durability and resistance corrosion. ideal works even in difficult conditions use. Gun equipped is in nozzle FULL-JET o diameter hole 2.5 mm, replaceable, with thread connection external M12x1.25, which is characterized significantly wider a stream air and greater power operation at a pressure of 2 bar, in comparison for standard nozzle o diameter hole 1.5 mm. instead of nozzle FULL-JET install can other nozzles – see accessories for guns EWO. depending on the connection we distinguish Gun terminated a plug EUROSTANDARD 7.2 or fitting for hose o diameter 6 mm, 9 mm and 13 mm. Material: aluminum (forging). Diameter hole nozzle: 2.5 mm. pressure operating: 2 ÷ 8 bar. Operating temperature: od -10°C up to +50°C.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh quality aluminum Gun for compressed air, intended for removing with surface all contaminants: liquids, fine chips, filings etc. regulation flow degree press lever. made with forged aluminum, protected anodizing ensures high strength, durability and resistance corrosion. It can be used for water. ideal works on lines production, thanks to mounting plug EUROSTANDARD 7.2 in upper parts body. Gun equipped is in standard nozzle o diameter hole 1.5 mm, with thread connection external M12x1.25. instead of nozzle standard install can other nozzles – see accessories for guns EWO. Material: aluminum (forging). Material Connections: brass nickel-plated. Diameter hole nozzle: 1.5 mm. pressure maximum: 10 bar. pressure operating: 2 ÷ 8 bar. Operating temperature: od -10°C up to +50°C.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsA universal Gun for air, water a also liquids non-explosive. intended mainly for blowing out contaminants, also in hard-to-reach places. is characterized high force air blowing, with the possibility regulation rate flow. light The design, ergonomic shape gun and low force press trigger ensures large comfort use. standard Gun equipped is in socket with thread 1/4" BSP. this model Available is in version with nozzle 90 mm bent Star-Tip, which not is replaceable. Sound level below 85 dB, in accordance with the European Machinery Directive art. 1.5.8. compliant of the standard OSHA 1-13.1. (European Agency safety and Health in use). wide range additional accessories allows on adjustment for specific requirements applications. Material: POM (body), brass (valve) sealing: NBR. Working pressure: 16 bar. pressure bursting: 64 bar. Operating temperature: od -20°C up to +60°C.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsDouble nipple with male thread 1/4" BSP / M12x1.25 male, serving for connections nozzle BLOWSTAR with gun for air EWO. Material: aluminum.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsAn extension straight or bent for guns for air with thread internal M12x1.12. Available in four various lengths (150 mm, 300 mm, 450 mm and 800 mm). An extension allows access for hard reachable places, thanks to which safety use is higher, a conditions use are more comfortable. extensions can be mounted together with of all nozzles with thread M12x1.12. Od side mounting for body gun extensions have a nut locking in order to correct settings. increases safety and comfort use. Material: aluminum anodized. Working pressure: 10 bar. Operating temperature: od -10°C up to +50°C.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight plastic compressed air gun intended for removing all types of contaminants from surfaces: liquids, small chips, filings, etc. Flow is controlled by how far the lever is pressed. Made of durable glass-fibre-reinforced polyamide. The ergonomic shape and effortless lever operation ensure comfortable use. Its low weight and plastic construction make it particularly suitable for the automotive, textile and electronics industries, etc. The gun is equipped with a replaceable extended bent nozzle made of nickel-plated steel, with an M12x1.25 male connection thread, allowing access to hard-to-reach areas. Other nozzles can be fitted in place of the extended bent nozzle – see EWO gun accessories. Connection: EUROSTANDARD 7.2 plug or 1/4" BSP female thread. Material: body - blue glass-fibre-reinforced polyamide (PA6 GK30); seals – NBR, PU. Maximum pressure: 10 bar. Operating pressure: 2 ÷ 6 bar. Working temperature: from -10°C to +50°C.

































