0

Our products

    Filters
      Product categories
      Working pressure [bar]
      Minimum operating temperature [°C]

      Minimum operating temperature [°C]: -273 — 260

      Maximum operating temperature [°C]

      Maximum operating temperature [°C]: 30 — 1100

      Material
      Vacuum resistance
      Standard length [m]
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Spigot with thread external for system SPEEDFIT used in installations compressed air. The installation can be made with use pipes with plastic or metal (copper, brass, aluminum). pushing spigot in coupling obtain possibility connecting for installation thread external. Material: brass. Working pressure: 10 bar (+23°C), 7 bar (+70°C). Operating temperature: od -20°C up to +70°C.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Miniature valve reducing type RML (coupling push-in on inlet and the outlet valve) intended for reduction higher pressure for lower pressure za valve. range pressure output: 1 ÷ 8 bar. Working pressure: 10 bar. Operating temperature: od -20°C up to +60°C. medium: filtered compressed air, oiled or not oiled.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details

          A nut for spigot S and SF, steel carbon, type UM

          All products | Low-pressure fittings and adapters
          0 €
          A nut type UM with thread metric or BSP, close for DIN 3870, for spigot type S and SF. Material: steel carbon, galvanized.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Unreinforced and very flexible hose with transparent PVC intended for pressureless (or under very low pressure) conveying water, beer, wine, alcohols o a concentration up to 20%, juices, drinks, other liquids food. Not is recommended for milk and products milk and for oils and greasy substances food. used also for liquids in use general-industrial, for light chemicals (e.g. diluted acids and bases) and as A guard pipes, lines, cables etc. For the hose, the stated pressure value is the approximate value of the recommended working pressure, assumed for a typical PVC hose, at a safety factor of 5:1. Use of the hose at a specific working pressure should be preceded by a test under operating conditions. Standards and requirements: Food industry, food contact: compliant with the European requirements 1935/2004/EC and 10/2011/EU (simulant fluids A, B and C), 2023/2006/EC (GMP). Hose material: transparent PVC. Working pressure: low, up to a few bar, depends on temperature. Operating temperature: od -5°C up to +60°C.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details

          Cutter for hoses plastic

          All products | Pneumatic hoses
          0 €
          Cutter for hoses plastic o diameters in the scope 3 ÷ 12 mm. color: orange.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details

          A clamp DIN 3015 double, polypropylene, type 301

          All products | Clamps for hydraulic pipes
          0 €
          A DIN 3015 double clamp, type 301 (with a top plate) Intended for fast, easy, durable and aesthetic fastening pipes, cables and hoses in various branches industry, in installations above-ground and marine. made in accordance with the standard DIN 3015. assembly clamp for the structure performed is using welding base clamp (exists possibility screwing or mounting on a rail). standard A clamp has profiled (grooved) surface hole for a pipe. Available is also A clamp with smooth surface hole, Intended for hoses and cables, marked with the letter H on the end index. besides standard element metal can order: plates extension, rail and screws for mounting sets clamps. selection element should consulted with TUBES INTERNATIONAL®. Material clamp: green polypropylene. Material bolts: steel galvanized. Material plate: steel galvanized. Material base: steel carbon. Operating temperature: od -30°C up to +90°C.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details

          A clamp for mounting pressure gauge type FM 632

          All products | Manometers reducers and valves
          0 €
          A clamp for mounting panel for pressure gauge type FM 632 with rear connection.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Flexible a steel braid, used for securing hoses against damage mechanical, abrasion and temperature. ensures also increase ich strength at elevated pressure. can be clamped a clamp crimp or ferrules. Material: steel AISI 304.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details

          Cutting ring, type B11

          All products | Cutting ring fittings
          0 €
          Cutting ring type B11 for connecting pipes copper and hoses with plastics for coupling type B. Material: brass.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details

          Crimping press FINN-POWER P20 CS

          All products | Hose and tube assembling machines
          0 €
          Press P20 CS Powered is motor electric 1.6 kW o voltage 12 V or 2.2 kW o voltage 24 V, powered with battery, Intended in particular for equipment cars service and vehicles technical. Diameter crimp set knob micrometric. indicator reaching diameter crimp, signalled is electrically using indicator light LED. press occurs in two versions in which head crimping can be placed po right or left side. All FINN-POWER crimping presses are adapted to work with interchangeable jaw sets (ordered separately). On example for range diameters crimp od 10 for 61 mm should order 12 sets jaws standard od FP-20-10 for FP-20-54.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Widely used for washing hot water floors and equipment industrial. is suitable also for use external. resistant to conditions atmospheric and abrasion. Not is resistant to oil, not recommended also for air with mist oil. W comparison with a hose "Tubes 2116" has thicker wall. Inner layer: white EPDM rubber. Reinforcement: a polyester braid. Outer layer: red or blue EPDM rubber micro-perforated. Working pressure: 10 bar. Operating temperature: od -40°C up to +100°C.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details

          Fitting angled with thread external BSPT, brass, type AI 13280

          All products | Low-pressure fittings and adapters
          0 €
          Fitting angled with thread external BSPT type AI 13280 Intended for connecting pipes copper, brass, steel, aluminum etc. and pipes and hoses with plastic (e.g. polyamide). range diameters external joined pipes od 4 for 22 mm. tightness connections obtained is through clamping ring on joined pipe and simultaneous pressing tubes with a ring for socket using a nut. standard: EN 1254-2. Material: brass.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details

          Bolt BANJO with o-rings, type D7

          All products | Banjo fittings
          0 €
          Bolt BANJO with o-rings type D7 for coupling type R28, R29. Material: brass nickel-plated. Working pressure: 18 bar.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Self-vulcanizing tape silicone PYROSIL used for sealing cover PYROJACKET and tape PYROTAPE. Not has layer adhesive, ale overlapping on each other or on PYROJACKET or PYROTAPE vulcanizes in several seconds. resistant to radiating heat, moisture and vibration. Due to very good strength dielectric, is suitable on insulator electric. at mounting Recommended is overlap 50% and clean, dry surface. Not is recommended for contact with flame and splashes molten metal. Material: silicone in color rust. Operating temperature: up to +246°C.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          High quality Connection Tee "T" with thread external BSPT, made entirely of steel AISI 316L, series 60210. no element plastic, and seal made of Viton ensure high resistance to action agents corrosion and substances chemical. used in industry chemical, food, pharmaceutical, electronic and in medicine. Material: steel AISI 316L. Operating temperature: od -15°C up to +225°C. Working pressure: 15 bar. Vacuum: 0.99 bar. sealing: Viton.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details

          Tee plug-in “T”, type R 5 NSF

          All products | Push-in fittings
          0 €
          Tee through-flow, series F type R 5 NSF. intended for industry food (e.g. for cold or hot water potable). no element plastic, coated coating nickel in special process chemical and seal made of Viton ensure high resistance to action detergents and other agents chemical. is suitable also for many applications in industry chemical, pharmaceutical, electronic and in medicine. Operating temperature: od -20°C up to +150°C. Working pressure: 16 bar. Vacuum: 0.99 bar. Material: brass nickel-plated. sealing: Viton (approved for contact with food through FDA). standards: NSF/ANSI 51, NSF/ANSI 61.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details

          Tee with thread internal BSP, steel stainless, type VT103

          All products | Fittings (pipes, fittings and connectors)
          0 €
          Tee with thread internal BSP for use in connections pipe installation industrial. Material: steel AISI 316. Working pressure: 10 bar.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          O-ring, type F.3, Intended for socket coupling FERRARI. Material: rubber SBR/NR.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details

          Gasket coupling TW DIN 28450, hypalon, type GSD

          All products | Tankwagen couplings and ECTFE-lined couplings
          0 €
          A profile gasket for a TW (tankwagen) coupling, type GSD (for a 4" coupling, an O-ring gasket type TWO is used). Material: hypalon (SCM). range temperatures (approximate): od -20°C up to +130°C.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Cream, flexible hose chemical o multilayer the structure designed specially, to connect resistance chemical with high service life in pump peristaltic. smooth Layer inner o very sound resistance chemical, free of plasticisers, resistant to acids, bases, salts, alcohols and ketones, o low absorption and adsorption liquids based on water. Layer outer with thermoplastic elastomer (Norprene®) ensures excellent properties and high service life at use in pump peristaltic. hose Meets the requirements of hygienic and for contact with food: American FDA 21 CFR 177.1520 and is resistant to most agents cleaning and disinfecting. sterilization steam, oxide ethylene or radiation. perfectly is suitable for dosing soaps and detergents, agents washing and for washing vessels. used for production and dosing various chemicals we all fields industry. length full roll hose 15 m. The given working pressure is determined relative to the bursting pressure at a safety factor of 1:5. Material: polyolefin / TPE (Norprene® - thermoplastic elastomer). Operating temperature: od -60°C up to +74°C. temperature brittleness: -60°C. Hardness: 61° Shore (A). Density: 0.98 g/cm³. Note: The product is packaged in the Tubes International Clean Zone (CLEAN ROOM) in compliance with rigorous standards. Return of the product after opening the package is not possible.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details

          Hydraulic hose EN 856 HI-PULSE 4SH

          All products | Hydraulic rubber hoses
          0 €
          A general-purpose hydraulic hose. Increased hose service life relative to the standard, confirmed by a test of 1.000.000 pulse cycles. Flame-retardant outer layer (MSHA). standards: EN 856 4SH, ISO 3862-1 4SH. Inner layer: black, oil-resistant synthetic rubber. Reinforcement: four layers of steel wire. Outer layer: black, oil-resistant synthetic rubber. Working pressure: from 250 bar to 420 bar depending on the diameter hose. Operating temperature: od -40°C up to +100°C (momentarily +120°C).
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Light, very pliable and flexible hose intended for extraction hot vapours, fumes, gases, air blowing and discharge air cooling. reinforced version hose SILICONE 1, o two layers fabric coated silicone and spiral steel placed between layers. resistant chemical, on radiation UV and aging. used m.in. for extraction gases in industry metallurgical, foundry, industry glass and ceramic, for hot air in dryers industrial, in printing houses and paper mills, in vehicles and engines for air cooling, incineration plants, a also for extraction exhaust gases and gases welding. smooth inside (in state extended), o very small radius bends enabling easy installations in tight spaces equipment and vehicles. not recommended for continuous dynamic bending. Assembly with clamps. Other diameters are available on special order. Hose material: two fabric glass coated red silicone. Reinforcement: spiral with wire steel, double outer cable with fibre glass. Operating temperature: od -70°C up to +250°C (momentarily up to +300°C).
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Light, flexible hose o calibrated diameter outer, intended for installation pneumatic, hydraulic, oil, fuel, lubrication and chemicals. compliant with the standard DIN 73378. Available in colours: natural, blue. Hose material: polyamide PA 12 (nylon). Working pressure: from 11 bar to 40 bar, depending on the diameter and wall thickness wall hose. Operating temperature: od -10°C up to +80°C.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Very flexible, resistant to abrasion, rupture and kinking spiral hose intended for installation pneumatic automotive systems brake. resistant to oil, gasoline, ozone and radiation UV. retains high flexibility at low temperatures. terminated on both sides fitting with thread external metric. The stated total length is the maximum hose length after stretching. Available in colour yellow and red. Hose material: polyurethane. Material spring: steel galvanised. The permissible Working pressure: 10 bar. Operating temperature: od -40°C up to +70°C.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Flexible hose o smooth surface internal intended for compressed air, water, light chemicals, agents fungicidal, fertilisers and pesticides. commonly used in agriculture for sprinkling, irrigation, spraying. Layer outer resistant to abrasion and conditions atmospheric. Inner layer: black PVC. Reinforcement: a polyester braid (double polyester braid for version REFITTEX 80 BAR). Outer layer: black PVC. Working pressure at a temperature of 20°C: 20 bar (white stripe), 40 bar (blue stripe), 80 bar for diameter internal 13 mm, above 50 bar (red stripe). As the working temperature rises, the hose's working pressure value decreases. Operating temperature: od -20°C up to +60°C.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details

          Hose welding double TWIN HOSE

          All products | Technical gases hoses
          0 €
          Double hose welding for oxygen and acetylene. made according to standards ISO 3821. Inner layer: black synthetic rubber. Reinforcement: double polyester braid. Outer layer: smooth synthetic rubber in color red (acetylene) and blue (oxygen). Working pressure: 20 bar. Operating temperature: od -32°C up to +80°C.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Free of braid version TO (Tube Only) hose VISIFLON, made with high quality PTFE serrated spirally (clockwise) ensuring exceptional among hoses PTFE flexible, flexibility and resistance to vibration. hose VISIFLON TO It can be used for conveying substances chemical, food, fuels, oils, paints, solvents, adhesives, dyes, detergents in conditions very low pressure. standard version VISIFLON TO made is with natural, semi-transparent PTFE, co allows visual control flow. version antistatic VISIFLON TO AS with PTFE with addition carbon (black) ensures discharge and dissipation charges electric for substances and conditions hazard electricity static. Material hose Meets the requirements of FDA (21 CFR 177.1550 for VISIFLON TO, 21 CFR 178.3297 for VISIFLON TO AS). Flame-retardant (UL94 V-0) and with a high oxygen index (LOI). assembly hose requires straightening barbs on length tail fittings, made on special equipment. fittings can be mounted then through clamping ferrules tube of steel stainless. value pressure working for hose PTFE VISIFLON without braid, applies only for temperatures 100°C, a in case vacuum for temperatures 80°C. above these temperatures occurs drop pressure working and vacuum. assuming use hose above these temperatures should to take into account and carry out appropriate test in conditions use. Hose material: spirally Serrated PTFE (teflon). Operating temperature: od -70°C up to +100°C (up to +230°C). Working pressure: from 2 bar to 4 bar - depending on the diameter hose.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Hose made is with smooth, seamless tube with PTFE. PTFE tube hose extruded is in strictly defined and controlled conditions, co ensures jej highest quality, minimal porosity and maximum possible for obtaining for hose smooth with PTFE flexible and flexibility. version thick-walled HW recommended is for heavier conditions use, gases (up to 100 bar) and for applications in which available cyclic changes temperatures use. braid made is with annealed wire of steel stainless AISI 304 o high strength on stretching 1700 N/mm 2, o strictly controlled angle arrangement and voltage bundles wire braid, co results minimal changes length hose under high pressure. Due to unique properties PTFE (large range temperatures use, resistance to most substances and compounds chemical, negligible adhesion surface) hose SMOOTHBORE perfectly is suitable for conveying substances chemical, food, fuels, oils, paints, solvents, adhesives, dyes, detergents, steam water etc. - as well as for classic installation high-pressure oil hydraulic. W case when identified is hazard electricity static (danger formation and accumulation charges electric), should use hoses SMOOTHBORE made with PTFE antistatic – version antistatic AS. antistatic teflon version AS is black (contains appropriate distributed in PTFE carbon) and has resistance R 8 Ω (in accordance with the standard ISO 8031 anex A). ensures to discharge and dissipation (dissipation) charges electric. Safety factor 3:1, if required is factor 4:1 (e.g. acc. to EN 16643) should multiply value through 0.75. at temperature use above +130°C maximum pressure working given in parameters should reduced o 0.75% on each 1°C above tej temperatures. for example at temperature 170°C maximum pressure working for hose AF-HWSB-06 is: 260 bar – (170°C-130°C) x 0.75 = 260 bar – 30% = 182 bar. The value "Wall thickness" given in the Technical data refers to the PTFE layer. Hose material: smooth PTFE (teflon). Reinforcement: single braid of steel AISI 304. Working pressure: from 55 bar to 240 bar - depending on the diameter hose. Operating temperature: od -70°C up to +260°C.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Hose delivery intended specially for conveying AdBlue ® (AUS32, DEF) - 32.5% water solution urea. layer inner hose constitutes black, smooth, antistatic (R‹10 6 Ω/m) EPDM rubber vulcanized without content sulfur. Layer inner hose not is contaminants additives aluminum, calcium, chlorine, copper, iron, potassium, magnesium, sodium, nickel and zinc, co guarantees retention the highest purity medium in accordance with the standard ISO 22241-2. is to especially important in industry automotive, in which AdBlue ® fully role regulator in order to decomposition in catalyst SCR harmful for environment oxides nitrogen. its use allows on meeting European standards emissions exhaust gases EURO 4, 5 and 6. liquid AdBlue ®, to was effective, must be very clean, co forces use specialized hoses, tanks and fittings resistant to AdBlue® and non-contaminating go. fittings and fittings for AdBlue ® should be made of steel stainless or appropriate plastic. except for automotive, hose used is also in industry chemical, on example at production fertilisers nitric. Inner layer: black EPDM rubber. Reinforcement: a synthetic braid. Outer layer: black EPDM rubber. Working pressure: 10 bar or 20 bar. Operating temperature: od -40°C up to +100°C (momentarily up to +120°C).
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Hose delivery intended for conducting steam saturated, o sound resistance to high temperature, abrasion and ozone. on request Available hose acc. to standards EN ISO 6134:2005 type 1 class A. Standard length: 60 m (or 120 m - contact Tubes International). Inner layer: black EPDM rubber. Reinforcement: cord synthetic. Outer layer: black EPDM rubber. Working pressure: 6 bar. Operating temperature: od -40°C up to +165°C.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Plug quick coupling NiTO of steel stainless AISI 316L with thread internal BSP. occurs in two systems 1/2″ and 3/4″. used in conditions elevated requirements in the scope hygiene and resistance to corrosion (e.g. industry food, hospitals). Not can connect directly element with various systems e.g. socket 1/2″ with a plug 3/4″. Material: steel AISI 316L. Working pressure: 25 bar. Operating temperature: od -20°C up to +150°C. Material seal: Viton.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Strong A clamp two-screw with double band with closure articulated for large loads. two screws and solid pins guarantee precise and tight connection hose with fitting. recommended for connections thick-walled, reinforced hoses industrial. A clamp made with high quality tape steel o wide 20 mm and 24 mm. flanged edges bridges prevents damage surface hose. A clamp has on band marking diameter minimum and maximum and Material. tightening bolts using wrench Allen. all element made of steel AISI 316.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details

          Hose crimper lever UPS-3

          All products | Hose and tube assembling machines
          0 €
          Crimping press UPS Intended is for crimping using lever manual, hoses o reinforcement textile ferrules sheet-metal type EC. standard equipped is in two sets (po 8 segments clamping) jaws. range use o diameter internal crimped hoses for press UPS-3: DN 3 ÷ 8 (range diameters internal ferrules EC: 8 ÷ 17 mm), DN 10 ÷ 16 (range diameters internal ferrules EC: 18 ÷ 28 mm). Do press exists possibility purchase base o index EC-100250.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          High quality three-way ball valve "L" type BK3L with thread internal NPT, intended for high-pressure installation hydraulic. Material: steel (body, ball, stem). seal: POM (ball), NBR (stem). Operating temperature: od -40°C up to +100°C (POM); od -20°C up to +100°C (NBR).
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Valve overflow VM45 limiting maximum pressure oil in systems hydraulic. allows free Flow rate liquids between connections P. W moment rise pressure over set value, occurs opening ways T and outflow excess oil for bowl. value pressure opening sets using screws (setting a wrench Allen, lock a lock nut). valve equipped in holes assembly. Material body: aluminum. Material valve: steel galvanized. sealing: NBR. maximum Working pressure: 260 bar. Operating temperature: od -20°C up to +90°C.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details

          Set connection, system SYNTESI

          Accessories for FRL | All products
          0 €
          Set connection for system SYNTESI type SY1 or SY2. W set occurs connector and 4 screws.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Coupling IBC on both sides with a thread internal trapezoidal compliant with the DIN EN 12713 standard. The trapezoidal threads that the IBC couplings are fitted with as standard match 100% the threads in the IBC containers of various manufacturers. Material: polypropylene. gasket: low-density polyethylene (LDPE). Working pressure: up to 7 bar. Operating temperature: from -10°C to +70°C (momentarily up to +80°C).
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Swivel coupling AK with thread internal BSP and with external BSP intended for mounting in industrial guns, in particular washing guns at the point of connection to the hose, where, due to operating the gun, its rotation is required. Material: steel AISI 316. Working pressure: up to 30 bar. sealing: Viton.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details

          Coupling socket STECKO, steel free-cutting

          All products | Fittings for high-pressure hoses
          0 €
          Coupling socket system STECKO for use in systems hydraulic for mining. Material: steel free-cutting, galvanized.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details

          Straight connector PUSH-IN for hose, brass, type AI 58040

          All products | Grease hoses and hose-end fittings
          0 €
          Straight connector PUSH-IN for hose terminated thread external BSPT or metric. Do use in technology lubrication. recommended material joined hoses is polyamide. Body material: brass nickel-plated. Material seal: O-ring (HNBR). Operating temperature: od -30°C up to +150°C. maximum Working pressure: 150 bar (for liquids), 30 bar (for air).
        Go to Top