- Home
- All products
Our products
Product categories
Working pressure [bar]
Minimum operating temperature [°C]
Maximum operating temperature [°C]
Material
Vacuum resistance
Standard length [m]
Select options This product has multiple variants. The options may be chosen on the product page / DetailsA nut for a connector type LET-LOK® Intended for tubes o diameter inch. Material: steel AISI 316.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsFitting straight JIC 37° with thread internal NPT (sealing on the thread – PTFE tape or anaerobic sealant). Material: steel carbon, galvanized.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible hose pressure for oils industrial, mineral, gasoline unleaded (EN 228:2017), oil drive (EN 590:2010), oil heating (DIN 51 603 1÷5). is suitable also for compressed air. Layer inner with black, smooth rubber NBR, antistatic R 6 Ω/m (EN ISO 8031:2009). Reinforcement a braid textile ensures factor safety 3.15 : 1. resistant to small vacuum for ok. 0.5 bar. Layer outer with black, smooth blend rubber NBR / EPDM resistant to oil, ozone, abrasion and conditions atmospheric. Inner layer: black NBR rubber. Reinforcement: textile braid. Outer layer: black NBR rubber/EPDM. Working pressure: 25 bar. Operating temperature: od -40°C up to +80°C.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsPlug quick coupling ISO-B with valve, thread internal BSP, for use in high-pressure installations industrial (water, fuels and oils, gases, chemicals). W set with socket, creates on both sides shut-off coupling, which can find everywhere tam, where lines transfer must be connected and disconnected in order to operation or maintenance equipment, a loss liquid is undesirable. can be used interchangeable with quick coupling ISO-B other manufacturers. Material: brass. sealing: NBR. Operating temperature: od -20°C up to +100°C. Working pressure: up to 180 bar (depending on size quick coupling). Safety factor 4:1. Flow rate has been stated for a drop pressure 3 bar.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsValve throttle check type MRF OMV series COMPACT "O" for mounting in connections valves directional, used in systems pneumatic for regulation level flowing stream compressed air and direction flow. equipped in coupling push-in ensuring easy disassembly lines pneumatic. change setting at use a screwdriver, with the possibility mounting cover protective. Size: M5, 1/8″, 1/4″, 3/8″, 1/2″. Working pressure: up to 10 bar. Operating temperature: od -10°C up to +70°C. Material: brass nickel-plated.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsAdapter - plug high-pressure type A113 with thread external BSP (sealing 60° cone). Material: steel AISI 316L.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsFitting pressure-gauge straight JIC37° with thread internal BSP (sealing using washer metal), type MAV. Material: steel carbon, galvanized.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsGrease nipple (lubricator) series SKILLAIR®, without plates end, ensures correctness lubrication mist oil equipment in installations pneumatic. Size: 100, 200, 300. capacity bowl: 50 cm³ - size 100, 95 cm³ - size 200, 160 cm³ - size 300. Supply pressure: up to 15 bar (13 bar - size 200, 300). Operating temperature: up to +50°C. Connection: 1/4" BSP female ÷ 1". Flow rate: 1500 l/min - size 100, 3700 l/min - size 200, 5500 l/min - size 300 (at an inlet pressure of 6 bar and Δp = 1 bar). way filling oil: STD - version standard, filling through disassembly bowl or plug, CA - filling Automatic, replenishment only during use lubricator, CD - filling vacuum, drop pressure inside bowl allows its filling, CAML - filling Automatic with level minimum, CDML - filling vacuum with level minimum.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsSocket without valve quick coupling TEMA STANDARD (NORDIC RANGE) thread internal BSP, NPT. socket has additional O-ring (except for size 3/16"), thanks to which is suitable for installation gas. has also ring securing against accidental disconnection. It is intended for heavy conditions use. Application: hydraulics power (oil hydraulic), industrial (water, steam, fuels and oils, gases and chemicals). Material: steel stainless AISI 316. Working pressure: up to 300 bar (depending on the diameter). Safety factor 4:1. sealing: Viton. Operating temperature: od -20°C up to +200°C. Flow rate has been stated for a drop pressure 3 bar.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsFerrule assembly crimped for ends for thin-walled hoses for freon, type 2015B. Material: aluminum.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible, soft hose rubber with external a braid of galvanized steel, intended for gasoline and oils petroleum-based such as e.g. oil drive, heating, lubricating. mounted in installations fuel and oil small vehicles and equipment industrial. It can also be used for water, cooling liquids, non-oxidising detergents, air. Based on the requirements of the DIN 73379 standard. Layer inner with smooth, black rubber NBR. The external reinforcing braid of galvanized steel provides high pressure resistance. W braid black band marking. The maximum working temperature depends on the medium: for gasoline, gasoline unleaded, fuels up to 50% content hydrocarbons aromatic: +40°C; for diesel oil (diesel): +80°C; for water and cooling liquids based on ethylene glycol: +90°C; for air: +80°C; for liquid, non-oxidising detergents: +80°C. Hose material: black NBR rubber. Reinforcement: external braid wire of galvanized steel. Working pressure: from 10 bar to 20 bar, dependent od diameter hose. Operating temperature: od -35°C up to +80°C (Maximum temperature dependent od medium).
Select options This product has multiple variants. The options may be chosen on the product page / DetailsValve shut-off alloy series STP-BX with thread internal and coupling push-in used mainly as valve safety. Po mounting on the connection supply actuator allows on Flow rate air only in the presence pneumatic signal control. actuator is stopped po a drop pressure control. Working pressure: 0.5 ÷ 10 bar. Operating temperature: od -10°C up to +60°C. Body material: brass nickel-plated. sealing: NBR.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsAdapter STORZ with thread internal BSP, with reducer, intended for installation transfer for liquid and bulk substances. used in firefighting, systems irrigation, industry chemical, food, agriculture etc. characterized by high, unobstructed diameter bore. O symmetrical construction parts connection, thanks to this in straight way combines je of each other. connect can element o the same spacing lugs. Material: steel stainless. Working pressure: 16 bar. Gasket: Viton.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsAdapter - Elbow 90° high-pressure JIS type A405 with thread external BSP (sealing inverted 60° cone) - TOYOTA and with thread external BSP (sealing ISO-1179 type G - an O-ring with a retaining ring). Material: steel carbon, galvanized.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsAdapter reducing with thread external and internal BSP for use in connections pipe, e.g. installations water hot and cold. Material: brass. Operating temperature: od -10°C up to +100°C. Working pressure: 10 bar.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsA fitting tubular with thread external UNF, for hose for air conditioning type 3055. Material: steel.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsFitting bulkhead straight type LET-LOK® with thread external NPT for a metric tube Intended mainly for industry chemical, petrochemical, pharmaceutical, power generation, nuclear power plants and process engineering. The permissible pressure working specifies on the basis of diameter outer and wall thickness wall tubes (details in the attachment). Material: steel AISI 316.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsPlug quick coupling TEMA STANDARD (NORDIC RANGE) with a shut-off valve and thread internal BSP and NPT. intended for heavy conditions use. Application: hydraulics power (oil hydraulic), industrial (water, steam, fuels and oils, gases and chemicals). Material: brass chrome-plated for size 1", steel galvanized above 1". Working pressure: up to 450 bar (depending on the diameter). Safety factor 4:1. sealing: Viton or NBR. Operating temperature: od -30°C up to +100°C (for NBR), od -15°C up to +200°C (for Viton). Flow rate has been stated for a drop pressure 3 bar.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible, soft hose rubber with external a braid textile, intended primarily for installation fuel gasoline leaded and unleaded and oil drive small vehicles (cars, motorcycles, mopeds, tractors garden) or equipment industrial. mounted e.g. between pump fuels a carburettor. Not is suitable for engines with system injection fuels. It can also be used for water, cooling liquids, non-oxidising detergents, air. Based on the requirements of the DIN 73379 standard type B (03/1982). Layer inner with smooth, black rubber NBR. The external braid vulcanised with rubber reinforces the hose and protects against contact with hot element. The maximum working temperature depends on the medium: for gasoline, gasoline unleaded, fuels up to 50% content hydrocarbons aromatic: +40°C; for diesel oil (diesel): +80°C; for water and cooling liquids based on ethylene glycol: +90°C; for air: +80°C; for liquid, non-oxidising detergents: +80°C. Hose material: black NBR rubber. Reinforcement: external black textile braid. Working pressure: 10 bar. Operating temperature: od -35°C up to +120°C (momentarily), Maximum temperature use dependent od medium.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsValve shut-off V3V electric, series SKILLAIR®, without plates end, serves for separation the system working od air supply. is to valve normally closed, three-way. W position closed cuts off air supply simultaneously venting configuration, co makes go especially useful during work service. Size: 100. Supply pressure: up to 10 bar. Operating temperature: up to +50°C. Flow rate: 1650 l/min (at an inlet pressure of 6 bar Δp = 1 bar).
Select options This product has multiple variants. The options may be chosen on the product page / DetailsSwivel coupling STORZ with thread external BSP intended for installation transfer for liquid and bulk substances. used in firefighting, systems irrigation, industry chemical, food, agriculture etc. O symmetrical construction parts connection, thanks to this in straight way combines je of each other. connect can element o the same spacing lugs. Material: aluminum. Working pressure: 16 bar. gasket: white NBR rubber.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsAdapter - Elbow 90° high-pressure JIS type A405T with thread external BSP (sealing inverted 60° cone) - TOYOTA and with thread external BSPT (sealing on the thread). Material: steel carbon, galvanized.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsA fitting BURGACLIP with thread internal UNF SAE - sealing on a 45° cone, for hose for air conditioning type 3090. allows on connection lines rubber with element the system air conditioning. clips and clamps available as separate assortment. Material: steel.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsUnion with thread internal BSP for use in connections pipe, e.g. installations water hot and cold. Material: brass. Operating temperature: od -10°C up to +100°C. Working pressure: 10 bar.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery pliable and flexible hose for gasoline unleaded and oil drive cars passenger, trucks and tractors. It can be used in compartment engine trucks. Layer inner with black, smooth rubber NBR highly resistant to fuel (resistance to oil: RMA class A), suitable for use with greater fuels automotive (standard oil drive B7 (EN590:2017), biodiesel B20, B100, standard gasoline unleaded E5 (EN228:2017), E10, E85 and E100 - 100% ethanol). Reinforcement strength a braid textile ensures Safety factor 4:1. Layer outer with black, smooth, high quality rubber synthetic resistant to oil, ozone and conditions atmospheric. commonly used hose fuel for vehicles automotive. compliant with standards SAE J30R2 and SAE J30 R6. Inner layer: NBR rubber. Reinforcement: textile braid. Outer layer: black synthetic rubber. Working pressure: 12 bar. Operating temperature: od -40°C up to +100°C externally up to +120°C.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsLeak-free plug quick coupling "flat-face" ISO-F with a shut-off valve and thread internal BSP. Application: hydraulics power (oil hydraulic). intended mainly for machine construction. socket has stem securing against accidental disconnection. quick coupling can be operated one hand. interchangeable with quick coupling ISO-F other manufacturers. Material: steel galvanized. sealing: NBR, Viton. Operating temperature: od -25°C up to +200°C, depending on kinds seal. Working pressure: up to 300 bar (depending on size quick coupling). Safety factor 4:1. Flow rate has been stated for a drop pressure 3 bar.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsValve shut-off Controlled manually V3V series SYNTESI®, with end connections, serves for separation the system working od air supply. is to valve three-way, two-position, normally closed. W position closed cuts off air supply and vents configuration, co makes go especially useful at performing work service. has configuration allowing on mounting dwu in size SY1 or three in size SY2 padlocks o diameter 3 mm. alternatively Available is version with a hole Ø 7 for single padlock. On rear and front surface valve is found the connection auxiliary (1/8” for rate SY1 and 1/4” for size SY2) for connection pressure gauge, sensor pressure or for additional draw air. Size: SY1, SY2. Connection: 1/8" BSP female, 1/4", with the front and with the back. Supply pressure: up to 15 bar, depending on size. Operating temperature: od -10°C up to +50°C. Flow rate nominal: for 4000 l/min, depending on size (at an inlet pressure of 6 bar and Δp = 1 bar).
Select options This product has multiple variants. The options may be chosen on the product page / DetailsStraight connector reducing type LET-LOK® for a metric tube Intended mainly for industry chemical, petrochemical, pharmaceutical, power generation, nuclear power plants and process engineering. The permissible pressure working specifies on the basis of diameter outer and wall thickness wall tubes (details in the attachment). Material: steel AISI 316.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsCoupling STORZ with thread internal BSP and thread external BSP Intended for installation transfer for liquid and bulk substances. used in firefighting, systems irrigation, industry chemical, food, agriculture etc. characterized by high, unobstructed diameter bore. O symmetrical construction parts connection, thanks to this in straight way combines je of each other. connect can element o the same spacing lugs. Material: aluminum. Working pressure: 16 bar. gasket: white NBR rubber.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsAdapter - Elbow 90° high-pressure type A116N with thread external BSP (sealing 60° cone) and with thread external BSP (sealing ISO-1179 type G: O-ring with a retaining ring), adjustable. Material: steel carbon, galvanized.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsA fitting 90° BURGACLIP with thread internal UNF SAE - sealing on a 45° cone, for hose for air conditioning type 3090. allows on connection lines rubber with element the system air conditioning. clips and clamps available as separate assortment. Material: steel.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsNipple reducing with both thread external BSP for use in connections pipe, e.g. installations water hot and cold. Material: brass. Operating temperature: od -10°C up to +100°C. Working pressure: 10 bar.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsRing inch rear for use in connectors type LET-LOK®. Material: steel AISI 316.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsGasket lip Intended for hoses suction-delivery. Not is suitable for applications food. resistant to greases and oils. Material: Viton. Operating temperature: od -15°C up to +200°C.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible hose rubber CODAN 3106 intended for gasoline leaded and unleaded. used for connections e.g. carburettor with pump fuels in cars, motorcycles, mopeds, tractors garden, etc. Not is suitable for engines with system injection. Based on the requirements of the DIN 73379 standard type B (03/1982). Layer inner with smooth, black blend rubber NBR / PVC. external braid with fibre polyester vulcanised with rubber reinforces hose and secures against contact with hot element. It can also be used for water, cooling liquids, non-oxidising detergents, air. The maximum working temperature depends on the medium: for water and cooling liquids based on ethylene glycol: +90°C, for air: +80°C, for liquid, non-oxidising detergents: +80°C, for diesel oil (diesel): +80°C, for gasoline, gasoline unleaded, fuels up to 50% content hydrocarbons aromatic: +40°C. Hose material: black NBR rubber/PVC. Reinforcement: external textile braid (black polyester). Working pressure: from 5 bar to 13 bar, depending on the diameter hose. Operating temperature: od -30°C up to +100°C (momentarily), Maximum temperature use dependent od medium.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsHanger on jaws for press P20 supplied is with handle magnetic for quick replacement jaws working. possibility mounting on floor or for stations (table) for press. ensures safe and easy space for storage set jaws. capacity: 12 holes.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsValve shut-off male V3V series G with thread internal BSP serves for separation air supply od parts working installation. Po closing air za valve is bled for atmosphere. especially recommended as protection at works maintenance. W set found angle bracket/A handle assembly, padlock and 2 keys. Do connecting individual element of each other, serve sets connecting GA (shape L, T, U). Size: 200, 300, 400. Connection: 1/8" BSP female ÷ 1/2". Supply pressure: up to 10 bar. Operating temperature: up to +70°C. Control: hand.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsAdapter - Elbow 90° high-pressure type A114N, adjustable, with thread external BSP (sealing ISO-1179 type G: O-ring with a retaining ring) and with thread internal BSP, with a nut swivel (sealing 60° cone, O-ring). Material: steel carbon, galvanized.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsNipple with both thread external BSP for use in connections pipe, e.g. installations water hot and cold. thread 1.1/2" and 2" - thread BSPT made acc. to ISO 7/1. Material: brass. Operating temperature: od -10°C up to +100°C. Working pressure: 10 bar.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsRegulator MR FC series BIT. A version with a controlled bleed, enabling increased accuracy in maintaining the set output pressure value through a continuous, slight air bleed to the atmosphere. Pressure gauge connection: 1/8" BSP female. Output pressure range: 0 ÷ 2 bar, 0 ÷ 4 bar or 0 ÷ 12 bar. Supply pressure: up to 13 bar. Operating temperature: up to +50°C.



















































