0

Our products

    Filters
      Product categories
      Working pressure [bar]
      Minimum operating temperature [°C]

      Minimum operating temperature [°C]: -273 — 260

      Maximum operating temperature [°C]

      Maximum operating temperature [°C]: 30 — 1100

      Material
      Vacuum resistance
      Standard length [m]
        • Fuel hose for small engines, for fuel containing up to 10% ethanol TYGON® F4040-A
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          Translucent, yellow, flexible hose designed specifically for fuel and lubricating oils. Resistant to swelling and hardening caused by hydrocarbons, significantly reducing the risk of cracking and leakage. Minimal extractability protects fuel purity, and a low permeation rate for aromatic substances protects the operator and the environment. Resistant to ozone and UV radiation. The hose's flexibility facilitates installation even in tight spaces. The translucent wall allows flow monitoring. The hose is resistant to most petroleum products and fuels (including those with up to 10% ethanol content) and can be used for petrol, kerosene, diesel and heating oil, lubricants, cutting coolants and glycol-based fluids. Widely used and proven in thousands of applications: small engines, automotive, recreational vehicles, garden mowers, chainsaws, coolant and lubrication systems, cutting and polishing equipment. Compliant with REACH and RoHS 2011/65/EU regulations. Pressure safety factor 5:1. Assembly on nipples and fittings using clamps and ties. The maximum working pressure is given for a temperature of 23°C. Material: PVC (special). Maximum operating temperature: +74°C. Brittleness temperature: -37°C. Hardness: 57 Shore (A). Density: 1.26 g/cm³. Note: The product is packed in the Tubes International CLEAN ROOM clean zone in compliance with strict cleanliness standards. The product is not subject to return.
        • Inch-size pneumatic hose for brake installations PA12 S40 - SAE J844
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          General-purpose pneumatic hose in inch sizes. Made of polyamide PA12 (PA12 S40 PHL). Resistant to water and oily air. Designed and used for pneumatic air brake installations of trucks in accordance with SAE J844 type A standard. Used for industrial pneumatic installations; it can also be used for hydraulic, oil, fuel, lubrication installations as well as for varnishes and solvents. The calibrated outer diameter allows connection to the installation using push-in fittings of inch sizes. The standard colour of the hose is black, which, due to its high UV resistance, is also recommended for outdoor applications. Other sizes and colours of the hose may be available on special order. Standards and requirements: SAE J844:2004 (type A) - Nonmetallic Air Brake System Tubing. According to this standard, unreinforced hoses are marked as "type A", and braid-reinforced hoses as "type B". Hose material: polyamide PA12. Hardness: 65 Shore (D). Working pressure: from 22 bar to 32 bar, depending on hose diameter and wall thickness. Operating temperature: from -40°C to +100°C (momentarily up to +110°C; for water-based liquids up to +70°C).
        • Silicone hose for food substances and beverages, VERSILON™ SPX-60 FB
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          A soft and flexible peroxide-cured silicone hose, designed specifically for food substances and beverages. Designed for applications requiring flexibility, bend resistance and durability. A hose with optimized physical material properties: tensile strength, maximum elongation and compression set – for increased durability. The hose's very smooth inner surface minimizes the possibility of contaminant build-up during fluid flow. Specifically designed for pouring food liquids: coffee, tea, beverages and fruit juices. Used in the production and pouring of cosmetic fluids. Compliant with the RoHS 2011/65/EU material directive and the REACH 1907/2006/EU regulation - contains no hazardous or banned substances. Meets FDA 21 CFR 177.2600 requirements. Compliant with European requirements 1935/2004/EC, 10/2011/EU (simulant liquids B and D1 – for hydrated, acidic and dairy products) and 2023/2006/EC (GMP). Can be sterilized by steam (18 min, 1 bar, +134°C), ethylene oxide, or radiation (up to 2.5 Mrad). Pressure safety factor 5:1. Mounted on nipples and fittings without sharp barbs using clamps and bands. Inner layer: translucent silicone. Hardness: 61 ± 4 Shore (A). Density: 1.16 g/cm3. Operating temperature: from -50°C to +200°C.
        • Silicone hose for biotechnological applications, hardness 65 Shore (A), Sani-Tech® STHT®-65
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          Top-quality platinum-cured silicone hose intended for biotechnological applications. Made of ultra-pure, biopharmaceutical-grade silicone with a hardness of 65 Shore (A). The hose is manufactured in a certified class 7 clean room with full process and product traceability – the batch number is laser-marked on the hose. Very flexible, with an exceptionally smooth internal and external surface. Resistant to high temperatures, ozone, radiation, moisture and weather conditions. Does not adsorb or absorb odour or taste. Used for sterile filling and flow of substances requiring high purity: blood-derived products, medicines, cell cultures, laboratory fluids, biopharmaceutical processing products. Can be repeatedly sterilised in an autoclave, as well as with ethylene oxide or by radiation (up to 5.0 Mrad - 50 Kgray). Biocompatible – meets the requirements of USP Class VI, and/or USP, and/or ISO 10993-5, European Pharmacopoeia 3.1.9. Hygienic properties are confirmed by the BPOG extractables report and the Saint-Gobain validation guide for this hose. Compliant with RoHS 2011/65/EU and REACH 1907/2006/EU. Pressure safety factor 5:1. Recommended assembly with special biopharmaceutical fittings and connectors, e.g. Pure-Fit® or special systems with factory-integrated fittings (Sani-Tech® Sani-Link® Molded Assemblies, Sani-Tech® TA Tubing Assemblies). Available in other sizes on special order. Material: translucent silicone. Hardness: 65 Shore (A). Density: 1.21 g/cm³. Operating temperature: from -62°C to +260°C.
        • Silicone hose with extended service life for peristaltic pumps, Sani-Tech® ULTRA-C
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          Top-quality, new-generation platinum-cured silicone hose intended for biotechnology applications, with minimized extractables and extended service life in peristaltic pumps. Made of ultra-pure biopharmaceutical-grade silicone. The hose is manufactured in a certified class 7 cleanroom with full process and product traceability – the batch number is laser-marked on the hose. Very flexible, with an extremely smooth inner and outer surface. Resistant to high temperatures, ozone, radiation, moisture, and atmospheric conditions. Does not adsorb or absorb odour or taste. Used for sterile filling, flow and operation in peristaltic pumps of substances requiring high purity: blood-derived products, medicines, cell cultures, laboratory fluids, biopharmaceutical processing products. Can be repeatedly sterilized in an autoclave, as well as with ethylene oxide or radiation (up to 5.0 Mrad - 50 Kgray). Biocompatible – meets the requirements of USP Class VI, and/or USP, and/or ISO 10993-5, European Pharmacopoeia 3.1.9. Hygienic properties confirmed by the BPOG extractables report and the Saint-Gobain validation guide for this hose. Very low total organic carbon (TOC) level. Compliant with RoHS 2011/65/EU and REACH 1907/2006/EU. Pressure safety factor 5:1. Recommended assembly with special biopharmaceutical fittings and connectors, e.g. Pure-Fit® or special systems with factory-integrated fittings Sani-Tech® Sani-Link® Molded Assemblies and Sani-Tech® TA Tubing Assemblies. A version of the hose with a hardness of 65 Shore (A) is available on special order. Material: translucent silicone. Hardness: 50 Shore (A). Density: 1.14 g/cm³. Operating temperature: from -62°C to +260°C.
        • Platinum-cured silicone delivery and suction-delivery hose, CLEARWAY PLATINUM D and SD
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          High-quality platinum-cured silicone hose. Available in two design versions: CLEARWAY PLATINUM D – a delivery hose, without a steel helix, CLEARWAY PLATINUM SD – a suction-and-delivery hose, with a steel helix. These versions have reinforcement made of spirally arranged layers of high-strength, light, white synthetic fabric. The CLEARWAY PLATINUM hose features a smooth, non-stick, pore-free internal surface, preventing the deposition of product particles and bacterial growth and facilitating hose cleaning. The outer layer is smooth, minimally corrugated for the version with a helix, and easy to clean with a mild detergent. The hose is intended for transferring high-purity products, food substances, and liquids with an alcohol content of up to 96%. Widely used in the food, pharmaceutical and cosmetics industries. Hose material: translucent silicone (PT3362) of food and pharmaceutical grade, odourless and tasteless. Meets hygienic and food-contact requirements: FDA, BfR, European Pharmacopoeia 3.1.9, USP Class VI, 3-A, ISO 10993, D.M. 21/03/73 (Italy), Arrete du 25 Novembre 1992 (France). Compliant with European requirements 1935/2004/EC, 2023/2006/EC (GMP), tested with simulant fluids B and D1 (for hydrated, acidic and dairy products). The hose is manufactured in a certified class 8 clean room (ISO 14644-1) with full process traceability. The manufacturing process is free of substances of animal origin, phthalates, adipates, nitrosamines and restricted materials, compliant with the RoHS 2011/65/EU material directive and REACH 1907/2006/EU regulation. Sterilisation: steam at max. +135°C under a pressure of 3.5 bar for max. 90 min, or hot air at max. +200°C for max. 30 min. To avoid impairing the mechanical properties of the hose, sterilisation should not be repeated earlier than one hour after the last cleaning. Cleaning: water up to 95°C; sodium hydroxide 1%, 80°C; nitric/phosphoric/peracetic acid 1%, 20°C; hydrochloric acid, sodium hypochlorite 200 ppm, 80°C, max. 20 min. Inner layer: translucent silicone. Reinforcement: polyester fabric layers, AISI 302 steel helix (SD version only). Outer layer: translucent silicone. Operating temperature: from -60°C to +200°C.
        • Reinforced silicone hose for biotechnological applications, Sani-Tech® STHT®-R
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          Top-quality, platinum-cured silicone pressure hose designed for biotechnology applications. Made of ultra-pure biopharmaceutical-grade silicone with a hardness of 65 (as in STHT-65 hose), reinforced with high-strength braid. The hose is manufactured in a certified class 7 cleanroom with full process and product traceability. Highly flexible, with exceptionally smooth inner and outer surfaces. Resistant to high temperatures, ozone, radiation, moisture and weathering. Does not adsorb odour or taste. Used for sterile filling and transfer of substances requiring high purity: blood-derived products, medicines, cell cultures, laboratory fluids and biopharmaceutical processing products. Can be repeatedly sterilised in an autoclave (particularly recommended), as well as with ethylene oxide or radiation (up to 5.0 Mrad - 50 Kgray). Must not be used for continuous steam service. Not recommended for use with hot oil or acids. Biocompatible - meets the requirements of USP Class VI, and/or USP, and/or ISO 10993-5, European Pharmacopoeia 3.1.9. Hygienic properties are confirmed by the BPOG extractables report and the Saint-Gobain validation guide for this hose. Assembly - with AISI 316 steel hygienic fittings crimped using ferrules, or with special plastic hygienic fittings, crimped or welded / vulcanised. Recommended pressure safety factor 4:1. Material: translucent silicone. Reinforcement: textile braid. Hardness: 65 Shore (A). Density: 1.21 g/cm³. Working temperature: from -62°C to +260°C.
        • Welding hose for acetylene, CODAN 2801 ACETYLEN, ISO 3821
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          Lightweight, flexible, smooth acetylene hose, compliant with EN ISO 3821. For use with industrial autogenous welding equipment, usually together with a blue oxygen hose. Can also be used for natural gas and air. Inner layer: black EPDM rubber. Reinforcement: polyester. Outer layer: red EPDM rubber. Working pressure: 20 bar. Operating temperature: from -30°C to +80°C.
        • Ribbed welding hose for acetylene, CODAN 2813 ACETYLEN, ISO 3821
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          Lightweight, flexible, ribbed acetylene hose compliant with EN ISO 3821 standard. The ribbed surface allows the hose to be easily dragged along the floor and prevents it from getting dirty. For transporting acetylene in oxy-fuel welding equipment used in industrial plants, shipyards, construction sites, etc. Due to its low weight, the hose is also ideal for compressed air. Inner layer: black EPDM rubber. Reinforcement: polyester. Outer layer: red EPDM rubber. Working pressure: 20 bar. Operating temperature: from -40°C to +100°C.
        • Temperature-resistant food hose for peristaltic pumps TYGON® E-65-F
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          White, flexible universal hose made of a special thermoplastic elastomer (TPE). Hose with exceptional resistance to ageing, weather conditions, UV radiation and ozone, with good chemical resistance. Extremely flexible and elastic, kink-resistant, retains its shape during easy and quick installation. Hose with high fatigue resistance to deformation, resistant to abrasion and cracking. Excellent for operation in peristaltic pumps. Resistant to repeated sterilization (up to five times without changing the hose's service life). Used for transferring and dosing cleaning chemicals in industry and services in CIP (Clean-in-Place) and SIP (Steam-in-Place) sterilization systems, and for universal industrial and laboratory applications. The soft hose material is very elastic and provides excellent service life of over 1000 hours of operation in a peristaltic pump. The hose is a favourable alternative to the commonly used PVC or silicone hoses. It has good chemical resistance to a range of chemical substances, especially acids and bases, oxidizing agents such as hydrogen peroxide, sodium hypochlorite or ozone. It is characterized by low gas permeability compared to rubber hoses. Meets European hygiene and food contact requirements: 1935/2004/EC and 10/2011/EU (simulant liquids B and D1, hydrated food, over 20% alcohol and dairy products – time and temperature according to certificate). Meets American FDA 21 CFR 177.2600, NSF-51 requirements. Compliant with REACH 1907/2006/EU regulation – contains no hazardous or banned substances. Can be sterilized with steam, ethylene oxide or radiation. Pressure safety factor 5:1. Assembly on nipples and fittings using clamps and bands. Maximum working pressure is given for a temperature of 23°C. Material: thermoplastic styrenic elastomer (TPE). Operating temperature: from -80°C to +121°C. Hardness: 65 Shore (A). Density: 0.89 g/cm³. Note: Product packed in the Tubes International CLEAN ROOM Clean Zone in compliance with strict cleanliness standards. Product is non-returnable.
        • Hydroformed steel hose for high pressures HP / THP / XHP
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          Hoses available only as complete hose assemblies with fittings crimped by Tubes International. For an individual quotation, use the enquiry form in the shop or download the hose assembly selection form (available as an attachment), complete it and send it to: sklep@tubes-international.com Special high-pressure steel hose with an increased wall thickness and closely spaced annular corrugations formed by hydroforming. Designed for chemicals, gases and steam under pressure and under high vacuum. Designed in accordance with EN ISO 10380 requirements. Supplied to order with fittings for steel hoses. For use at elevated temperatures, the working pressure must be reduced using the temperature correction factor according to EN ISO 10380 (details attached). Safety factor 4:1 (for dynamic conditions). The specified working pressure applies to dynamic conditions. Inner layer: corrugated AISI 316L steel hose, with DN 32 and DN 100 diameters made from AISI 321 steel. Reinforcement: single AISI 304 steel braid. Working temperature: from -273°C to +600°C (working pressure depends on temperature).
        • Highly flexible hydroformed steel hose compliant with EN ISO 10380 PARRAP®
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          Hoses available only as complete hose assemblies with fittings crimped by Tubes International. To receive an individual quotation, use the enquiry form in the online shop or download the hose assembly selection form (available as an attachment), complete it and send it to: sklep@tubes-international.com Top-quality, flexible and exceptionally pliable stainless steel hose manufactured in France. Annularly corrugated hose with a special corrugation shape (“omega”), manufactured by hydroforming across the entire diameter range. Bending radius approximately 25% smaller (better) than that of PARNOR hose and the requirements of ISO 10380. Available with a single or double high-strength braid, or without braid. Designed for conveying liquids and gases under pressure: water, steam, air, hot oil and chemicals, as well as for operation under high vacuum. Safety factor 4:1. Recommended for all critical industrial applications and dynamic applications, providing very high flexibility, reliability and long service life even under demanding operating conditions. Used in the chemical and petrochemical industries, nuclear power generation, shipbuilding, cryogenic technology, air conditioning and the food industry, among others. Supplied as complete hose assemblies (hoses) with welded fittings, according to the customer's order. Inner layer: corrugated hose made from AISI 321 or AISI 316L stainless steel sheet. Reinforcement: single or double AISI 304 steel braid. Working temperature: from -273°C to +600°C (working pressure depends on temperature).
        • Hydroformed steel hose compliant with EN ISO 10380 PARNOR®
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          Hoses available only as complete hose assemblies with fittings crimped by Tubes International. For an individual quotation, use the enquiry form in the shop or download the hose assembly selection form (available as an attachment), complete it and send it to: sklep@tubes-international.com Top-quality flexible and pliable stainless steel hose manufactured in France. Annularly corrugated hose with standard corrugation pitch and shape, manufactured by hydroforming across the full range of diameters. Available with single or double dense, high-strength braid, or without braid. Designed for conveying liquids and gases under pressure: water, steam, air, hot oil and chemicals, as well as for operation under high vacuum. Safety factor 4:1. Recommended for all critical industrial applications, providing high flexibility, reliability and long service life even under demanding operating conditions. Used in the chemical and petrochemical industries, nuclear power engineering, shipbuilding, cryogenic technology, air conditioning and the food industry, among others. Supplied as complete hose assemblies with welded fittings, according to the customer's order. Inner layer: corrugated hose made from AISI 321 or AISI 316L stainless steel sheet. Reinforcement: single or double AISI 304 steel braid. Working temperature: from -273°C to +600°C (working pressure depends on temperature).
        • White thermoplastic hose with a double polyester braid FP17500 MARINE
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          Lightweight, flexible high-pressure hose type R7 designed for hydraulic oil installations, gases, air, fuels, water-based fluids. Micro-perforated outer layer, resistant to hydrolysis and microorganisms, suitable for use in humid, salty environments. Standards: SAE 100R7, ISO 3949-R7. Inner layer: polyester. Reinforcement: double polyester braid. Outer layer: micro-perforated white polyurethane. Working pressure: from 155 bar to 207 bar, depending on hose diameter. Operating temperature: from -40°C to +93°C (for water and air up to +65°C).
        • Non-conductive thermoplastic hose with a synthetic braid 3TR7N
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          Non-conductive thermoplastic hose 3TR7N with synthetic braid is designed for high-pressure hydraulic installations with oil, especially near transformers and medium and high voltage electrical equipment. The construction includes a nylon inner layer, which allows for the conveyance of chemicals and water-based fluids. The outer layer is made of semi-matte non-stick type polyurethane, characterized by non-adhesive properties and preventing hoses from sticking together. Standards: SAE 100R7, ANSI A92.2 (standard for aerial work platforms - USA, in the range DN 3/16” ÷ 5/8”). Inner layer: polyamide. Reinforcement: synthetic braid. Outer layer: polyurethane. Working pressure: from 69 bar to 210 bar, depending on hose diameter. Operating temperature: from -40°C to +100°C (water-based fluids up to +66°C).
        • Non-conductive thermoplastic hose with a double synthetic braid 3TR8N
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          Non-conductive thermoplastic hose 3TR8N with double synthetic braid intended for high-pressure hydraulic oil installations, especially near transformers and medium- and high-voltage electrical equipment. The design includes a nylon inner layer, which allows the transfer of chemicals and water-based fluids. The outer layer is made of semi-matte non-stick type polyurethane, characterized by non-adhesive properties and preventing hoses from sticking together. Standards: SAE 100R8. Inner layer: polyamide. Reinforcement: double synthetic braid. Outer layer: polyurethane. Working pressure: from 140 bar to 350 bar, depending on hose diameter. Operating temperature: from -40°C to +100°C (water-based fluids up to +66°C).
        • Twin thermoplastic hose with an aramid braid S2230
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          Lightweight, flexible and durable R8 high-pressure thermoplastic hose in a twin version (two hoses with their outer layers welded together), intended for chemicals, solvents, paints, isocyanate, polyol, as well as gases, air, fuels and water-based fluids. Standards: SAE 100R8, ISO 3949-R8. Inner layer: PA12 polyamide. Reinforcement: double aramid braid. Outer layer: microperforated polyurethane. Working pressure: from 250 bar to 362 bar, depending on the hose diameter. Working temperature: from -40°C to +93°C (for water and air up to +65°C).
        • Twin thermoplastic hose with an aramid and steel braid MTBKH
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          Flexible hydraulic hose in a twin version (two hoses with their outer layers welded together), with an aramid braid and a steel braid for very high pressures, intended for oil hydraulic systems, fuels, gases, air and water-based fluids. Microperforated outer layer. Inner layer: polyester. Reinforcement: aramid braid + steel braid. Outer layer: microperforated polyurethane. Working pressure: from 175 bar to 500 bar, depending on the hose diameter. Working temperature: from -40°C to +93°C (for water and air up to +65°C).
        • Twin thermoplastic hose with an aramid and steel braid MTBKH
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          Flexible hydraulic hose in a twin version (two hoses with bonded outer covers), with an aramid braid and a steel braid for very high pressures, designed for oil hydraulic systems, fuels, gases, air and water-based fluids. Microperforated version available on request (for gases and air). Inner layer: polyester. Reinforcement: aramid braid + steel braid. Outer layer: polyurethane. Working pressure: from 375 bar to 425 bar, depending on hose diameter. Working temperature: from -40°C to +100°C (for water and air up to +70°C).
        • Twin thermoplastic hose with an aramid and steel braid SK2100
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          Flexible thermoplastic hose in a twin version (two hoses with their outer layers welded together), with an aramid braid and a steel braid for very high pressures, intended for chemicals, solvents, paints, isocyanate, polyol, as well as gases, air, fuels and water-based fluids. Thanks to the steel braid, the hose conducts electrical charges and can be used where static electricity poses a hazard. The hose should be earthed. Inner layer: PA12 polyamide, white or black depending on the batch. Reinforcement: aramid braid + steel braid. Outer layer: microperforated polyurethane. Working pressure: from 175 bar to 500 bar, depending on the hose diameter. Working temperature: from -40°C to +93°C (for water and air up to +65°C).
        • Twin thermoplastic hose with a polyester braid FP27010
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          Lightweight, flexible R7 high-pressure hose in a twin version (two hoses with their outer layers welded together) for forklift trucks. Intended for oil hydraulic systems, gases, air, fuels and water-based fluids. Standards: SAE 100R7, ISO 3949-R7. Inner layer: polyester. Reinforcement: double polyester braid. Outer layer: microperforated polyurethane. Working pressure: from 155 bar to 190 bar, depending on the hose diameter. Working temperature: from -40°C to +93°C (for water and air up to +65°C).
        • Twin thermoplastic hose with a steel braid MTB1
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          MTB1 thermoplastic hose with steel braid is a flexible high-pressure hose in a twin version (two hoses with bonded outer covers). Designed for conveying chemicals, solvents, paints, isocyanate, polyol, gases, air, fuels and water-based fluids. The steel braid construction enables electrical charges to be conducted, allowing the hose to be used in environments with static electricity hazards, particularly with fast-flowing non-conductive liquids such as chemicals, organic solvents and paints. A microperforated version for gases and air is available on request. The hose must be earthed during operation. Inner layer: polyamide. Reinforcement: steel braid. Outer layer: polyurethane. Working pressure: from 190 bar to 350 bar, depending on hose diameter. Working temperature: from -40°C to +100°C (for water and air up to +70°C).
        • Twin thermoplastic hose with a steel braid MTB2
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          Flexible thermoplastic MTB2 hose with double steel braid, designed for conveying chemicals, solvents, paints, isocyanate, polyol, gases, air, fuels and water-based fluids. Twin version (two hoses with bonded outer covers). The steel braid construction enables electrical charges to be conducted, allowing the hose to be used in environments with static electricity hazards, particularly with fast-flowing non-conductive liquids such as chemicals, organic solvents and paints. A microperforated version for gases and air is available on request. The hose must be earthed during operation. Inner layer: polyamide. Reinforcement: double steel braid. Outer layer: polyurethane. Working pressure: from 275 bar to 400 bar, depending on hose diameter. Working temperature: from -40°C to +100°C (for water and air up to +70°C).
        • Twin thermoplastic hose with a steel braid SM240
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          Flexible high-pressure thermoplastic hose with a steel braid, in a twin version (two hoses with their outer layers welded together). Intended for chemicals, solvents, paints, isocyanate, polyol, as well as gases, air, fuels and water-based fluids. Thanks to the steel braid, the hose conducts electrical charges and can be used where static electricity poses a hazard due to the rapid flow of electrically non-conductive fluids: chemicals, organic solvents and paints. The hose should be earthed. Inner layer: PA12 polyamide. Reinforcement: steel braid. Outer layer: microperforated polyurethane. Working pressure: from 180 bar to 300 bar, depending on the hose diameter. Working temperature: from -40°C to +93°C (for water and air up to +65°C).
        • Thermoplastic hose with a double aramid braid VE8 M
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          OL8M MARINE thermoplastic hose with aramid braid is a lightweight and flexible R8 type high-pressure hydraulic hose assembly, exceeding the requirements of the SAE 100R8 standard. Designed for transferring hydraulic oils, fuels, gases, air and water-based fluids. The micro-perforated outer layer is resistant to hydrolysis and the action of microorganisms, allowing use in humid and salty environments. Standards: SAE 100R8, ISO 3949-R8, MSHA. Inner layer: polyester. Reinforcement: aramid braids. Outer layer: micro-perforated polyurethane. Working pressure: from 250 bar to 350 bar, depending on hose diameter. Operating temperature: from -40°C to +100°C (for water and air up to +70°C).
        • Thermoplastic hose with a synthetic braid 3TR7
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          Thermoplastic hose 3TR7 with synthetic braid designed for high-pressure hydraulic oil installations and central lubrication systems. The inner layer made of nylon allows transport of chemicals, gases, air and water-based liquids. The outer sheath of semi-matte, micro-perforated non-stick polyurethane has non-adhesive properties and prevents sticking to other surfaces. The hose is characterized by lightness and high flexibility. Standards: SAE 100R7. Inner layer: polyamide. Reinforcement: synthetic braid. Outer layer: micro-perforated polyurethane. Working pressure: from 69 bar to 210 bar, depending on hose diameter. Operating temperature: from -40°C to +100°C (water-based fluids up to +66°C).
        • Thermoplastic hose with a double aramid braid VE8 M
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          AT8 MARINE thermoplastic hose with a double aramid braid is intended for conveying liquids, gases and air. Features a lightweight and flexible construction. The inner layer made of non-toxic material and the absence of adhesives in the braid structure ensure high hygiene standards. The product meets the requirements of FDA 21 CFR 177.2600 (for food substances containing less than 8% alcohol) and European standards 1935/2004/EC, 2023/2006/EC and 10/2011/EU (food simulants A, B, C, D1). Not intended for medical or pharmaceutical applications. The microperforated outer layer is resistant to hydrolysis and microorganisms, allowing use in humid and saline environments. Stainless steel fittings are recommended. Standards: SAE 100R8, ISO 3949-R8. Inner layer: non-toxic PBT polyester. Reinforcement: double aramid braid. Outer layer: microperforated polyurethane. Working pressure: from 165 bar to 1400 bar, depending on the hose diameter. Working temperature: from -40°C to +82°C (for water and air up to +70°C).
        • Thermoplastic hose with a double aramid braid S0230
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          Lightweight, flexible and durable thermoplastic high-pressure hose, type R8, designed for chemicals, solvents, paints, isocyanate, polyol, as well as gases, air, fuels and water-based fluids. Standards: SAE 100R8, ISO 3949-R8. Inner layer: PA12 polyamide. Reinforcement: double aramid braid. Outer layer: microperforated polyurethane. Working pressure: from 140 bar to 362 bar, depending on hose diameter. Working temperature: from -40°C to +93°C (for water and air up to +65°C).
        • Thermoplastic hose with a double aramid braid VE8 M
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          A light, flexible high-pressure hose of R8 type with a double aramid braid. Exceeds the pressure requirements of the SAE 100R8 standard. Designed for the transport of chemicals, solvents, paints, isocyanate, polyol, gases, air, fuels and water-based fluids. The light and flexible construction eases installation. The micro-perforated outer layer is resistant to hydrolysis and microorganisms, allowing the hose to be used in humid and saline environments. Standards: SAE 100R8, ISO 3949-R8, DNV-GL. Inner layer: polyamide. Reinforcement: aramid braids. Outer layer: micro-perforated polyurethane. Working pressure: from 250 bar to 350 bar, depending on hose diameter. Operating temperature: from -40°C to +100°C (for water and air up to +70°C).
        • Thermoplastic hose with a double polyester braid ATOXIC7 MARINE
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          AT7 MARINE thermoplastic hose with a double polyester braid is intended for conveying liquids, gases and air. Features a lightweight and flexible construction. The inner layer made of non-toxic material and the absence of adhesives in the braid structure ensure high hygiene standards. The product meets the requirements of FDA 21 CFR 177.2600 (for food substances containing less than 8% alcohol) and European standards 1935/2004/EC, 2023/2006/EC and 10/2011/EU (food simulants A, B, C, D1). Not intended for medical or pharmaceutical applications. The microperforated outer layer is resistant to hydrolysis and microorganisms, allowing use in humid and saline environments. Stainless steel fittings are recommended. Standards: SAE 100R7, ISO 3949-R7. Inner layer: non-toxic PBT polyester. Reinforcement: double polyester braid. Outer layer: microperforated polyurethane. Working pressure: from 70 bar to 230 bar, depending on the hose diameter. Working temperature: from -40°C to +82°C (for water and air up to +70°C).
        • Thermoplastic hose with a double polyester braid S2190
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          Lightweight, flexible and durable thermoplastic high-pressure hose, type R7, in a twin version (two hoses with bonded outer covers), designed for chemicals, solvents, paints, isocyanate, polyol, as well as gases, air, fuels and water-based fluids. Standards: DIN 24951, SAE 100R7, ISO 3949-R7. Inner layer: PA12 polyamide, white or black depending on the batch. Reinforcement: double polyester braid. Outer layer: microperforated polyurethane. Working pressure: from 157 bar to 220 bar, depending on hose diameter. Working temperature: from -40°C to +93°C (for water and air up to +65°C).
        • Thermoplastic hose with a double synthetic braid 3TR8
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          A 3TR8 thermoplastic hose with a double synthetic braid, designed for high-pressure hydraulic oil installations. The inner layer, made of nylon, allows the transport of chemicals, gases, air and water-based liquids. The outer coating of semi-matte, micro-perforated non-stick polyurethane has non-stick properties and prevents sticking to other surfaces. The hose is characterized by light weight and high flexibility. Standards: SAE 100R8. Inner layer: polyamide. Reinforcement: double synthetic braid. Outer layer: micro-perforated polyurethane. Working pressure: from 140 bar to 350 bar, depending on hose diameter. Operating temperature: from -40°C to +100°C (water-based fluids up to +66°C).
        • Thermoplastic-Teflon hose with a steel braid MT 1 HT
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          Specialist high-pressure hose with a PTFE inner layer, designed for hydraulic oils, aggressive chemicals, food substances, water and gases, resistant to high temperatures. Meets the requirements of FDA 21 CFR 177.1550, 1935/2004/EC and 10/2011/EU. Microperforated version available on request (for gases and air). Inner layer: Teflon (PTFE). Reinforcement: steel braid. Outer layer: polyurethane. Working pressure: from 105 bar to 375 bar, depending on hose diameter. Working temperature: from -40°C to +135°C.
        • Hot air delivery hose SAHARA® BN-PRO
          Select options This product has multiple variants. The options may be chosen on the product page / Details

          Hot air delivery hose SAHARA® BN-PRO

          Air and water hoses | All products
          0 €
          SAHARA® BN-PRO discharge hose is designed for conveying hot, dry air from a compressor to a tanker installation. The construction based on a thick, flexible wall ensures high resistance to kinking and durability in demanding working conditions. The inner layer is made of a special EPR rubber compound, characterized by increased resistance to hot air. The hose is used in road tankers for transporting bulk materials such as cement or feed, in product aeration systems and other industrial installations. The outer layer is resistant to ozone and weather factors. Inner layer: white EPR rubber. Reinforcement: synthetic cord. Outer layer: black EPDM rubber. Operating temperature: from -40°C to +200°C (momentarily up to +240°C).
        • High-pressure hose for washing with cold and hot water BALWASH 1W
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          A rubber hose with a single steel braid for high-pressure cold and hot water washing equipment in professional and industrial applications. Rubber resistant to abrasion, oils and weather conditions. A single steel wire braid provides high resistance to working pressure. Available in black and blue. Inner layer: black synthetic rubber. Reinforcement: single steel braid. Outer layer: black (BK) or blue (BL) synthetic rubber (micro-perforated). Operating temperature: up to +155°C.
        • High-pressure hose for washing with cold and hot water BALWASH 2W
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          Rubber hose with double steel braid for high-pressure cold and hot water washing equipment in professional and industrial applications. Rubber resistant to abrasion, oils and weather conditions. Double steel wire braid ensures high resistance to pressure and bending. Available in black and blue. Inner layer: black synthetic rubber. Reinforcement: double steel braid. Outer layer: black (BK) or blue (BL) synthetic rubber (micro-perforated). Operating temperature: up to +155°C.
        • High-pressure grease hose GR 7
          Select options This product has multiple variants. The options may be chosen on the product page / Details

          High-pressure grease hose GR 7

          All products | Grease hoses and hose-end fittings
          0 €
          Lightweight, flexible hose designed for high-pressure grease lubrication systems. Has an MSHA certificate. Inner layer: polyester or polyamide. Reinforcement: single polyester braid. Outer layer: polyurethane. Working pressure: from 200 bar to 400 bar. Operating temperature: from -40°C to +80°C.
        • Braided hose for high-purity applications, with low absorption and adsorption TYGON® 2475 IB
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          Colourless, transparent, flexible hose reinforced with polyester braid for biopharmaceutical applications, completely free of plasticisers and oils. Designed for higher pressures, e.g. in single-use ultrafiltration / diafiltration systems, chromatography, water for injection (WFI), deionised water, pharmaceutical and cosmetic substances. Features hydrophobicity (non-wettability) and very low absorption and adsorption of water-based fluids compared with PVC, as well as lower gas permeability than silicone hoses, protecting sensitive fluids against oxidation. This minimises the risk of changes in fluid properties even with repeated hose use. The glass-smooth, non-porous inner surface prevents contaminants from depositing and adhering, facilitating complete fluid drainage and hose cleaning. Resistant to chemical cleaning agents and disinfectants. Offers good chemical resistance to a range of substances: acids, alkalis, salts, as well as alcohols and ketones. Not recommended for hydrocarbons. Meets USP Class VI requirements. Hygienic properties are confirmed by the Saint-Gobain validation guide for this hose. Suitable for ethylene oxide or radiation sterilisation (up to 4.5 kGy). Complies with RoHS 2011/65/EU and REACH 1907/2006/EU. Can be used as a single-use or reusable product. Disposal of used hoses does not release hazardous substances (e.g. chlorine); incineration produces only carbon dioxide and water. Pressure safety factor 4:1. Assembly on hose tails and fittings using clips and clamps. Maximum working pressure is specified at 23°C. Material: polyolefin. Maximum working temperature: up to +52°C. Brittleness temperature: -78°C. Hardness: 72 Shore (A). Density: 0.9 g/cm³. Note: Product prepared in the Tubes International CLEAN ROOM in compliance with strict cleanliness standards. Product is non-returnable
        • Polyethylene hose for utility water and drinking water LLDPE
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          A light and flexible LLDPE (linear low-density polyethylene) hose designed for cold and periodically hot domestic water as well as for drinking water. LLDPE is stronger than traditional low- or medium-density polyethylene and is recommended for use with water. Typical applications include water purification and filtration systems, water treatment installations, ice-making machines, misting installations in catering and industry. May be used for drinking water in accordance with the relevant certificates. Not recommended for mineral oil, fuels and gases, or for compressed air installations at a pressure higher than 10 bar (20°C). For water, the maximum chlorine content is 4 ppm; higher values may shorten the service life of the hoses. The calibrated outer diameter allows connection to the installation using push-in fittings. Standards and requirements: Food industry, food contact: meets European food contact requirements 1935/2004/EC and 10/2011/EU (simulant liquids A, C and D1), 2023/2006/EC (GMP), as well as American NSF-51 hygiene requirements. Drinking water approvals: PZH (no. B.BK.60110.1534.2023, certificate valid until 16.11.2026), KTW, UBA, BfR (German requirements), as well as WRAS, NSF 4.1 (British) and NSF-61 (American). Hose material: polyethylene (LLDPE). Hardness: 55 ÷ 60 Shore (D). Working pressure: from 10 bar to 16 bar, depending on hose diameter. Operating temperature: from 0°C to +65°C (working pressure depends on temperature).
        • Polyolefin hose for a wide range of applications VERSILON™ 2001
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          Flexible, chemically resistant hose. Offers almost twice the service life of typical PVC hoses in peristaltic pump applications. It also provides good chemical resistance to a range of aggressive chemicals, such as polar solvents and corrosive media (acids, alkalis, salts, alcohols). It is durable and does not wear out over time, requiring less frequent replacement and helping avoid production downtime. Suitable for a wide range of uses, including demanding applications. Used for filling and portioning products, dispensing soap and detergents, water treatment lines, and transferring ink and chemicals. Ideal for analytical equipment, condensers, incubators, desiccators, and as a gas and drainage hose. High transparency provides clear visibility of flow. Free from plasticisers and oils - does not alter the properties of the conveyed media. Suitable for analytical testing. Proper incineration of used hoses does not release hazardous substances (e.g. hydrogen chloride). Meets US hygiene and food contact requirements FDA 21 CFR 177.2600. Can be sterilised with ethylene oxide or radiation (up to 2.5 Mrad). Compliant with REACH (2006/1907/EC) – contains no hazardous or prohibited substances. Pressure safety factor 5:1. Installed on hose tails and fittings using hose clips and clamps. We recommend consulting Tubes International specialists when selecting a hose for chemical applications. Maximum working pressure is specified at 23°C. Material: polyolefin. Working temperature: from -73°C to +57°C. Brittleness temperature: -78°C. Hardness: 69 Shore (A). Density: 0.88 g/cm³. Note: Product prepared in the Tubes International CLEAN ROOM under strict cleanliness standards. This product is non-returnable.
        Go to Top