- Home
- All products
Our products
Product categories
Working pressure [bar]
Minimum operating temperature [°C]
Maximum operating temperature [°C]
Material
Vacuum resistance
Standard length [m]
Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh quality socket water quick coupling NiTO 1" with thread internal and a shut-off valve. Material: brass chrome-plated. Working pressure: up to 25 bar. Operating temperature: up to +80°C. sealing: NBR (not is suitable for gasolines and oils). For the valve, an EPDM O-ring.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsSocket BCS quick coupling without valve with thread internal BSP for lances, guns and equipment washing. Material: steel stainless. Working pressure: 400 bar. Operating temperature: +160°C.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsMedium rate socket quick coupling with a nut on hose, intended for installation washing, filtration water deionized, machines industrial, detection leakage, etc. characteristic The design (not contains balls and ferrule protective) allows on easier, secure connection and disconnection one hand. An audible click signals a successful connection. length L - length total. Material: acetal. sealing: O-ring with NBR. Working pressure: for 8.3 bar. Operating temperature: od -40°C up to +82°C.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsAnaerobic adhesive fixing - hard removable general use. quickly cures, time fixing for steel ok. 4 min. use for fastening on shafts and gears toothed, wheels fitted and element coaxial. prevents loosening connections and leakage caused loads impact and vibrations. works not only on active metals, ale also on surfaces passive e.g. steel stainless. product tolerates light oiling and light contamination surface. color: green. Working temperature range: od -55°C up to +180°C. strength on shearing at tension: > 25 N/mm². Time to reach initial strength: 5-30 min. Time to reach full strength: 6-72 h (depending on material). compliant with German the standard DVGW(EN 751-1): NG-5146AR0619. Packaging - pen 50 ml.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsElbow silicone 45° reinforced polyester intended is for systems cooling and systems heating in vehicles (water, liquids cooling, air clean or with small amount mist oil). Do oils, fuels and mist oil recommended is version with layer inner fluorosilicone. Arm length: 100 mm (also available with arms of length 152, 250 mm). pressure factor safety: 3:1. hose meets standards SAE J20R1. hardness (version standard) ok. 65° Shore (A), density ok. 1.26 g/cm³. color layer outer: blue. Material: rubber silicone. Reinforcement: plies polyester. Working pressure: from 1.5 bar to 8.33 bar (depending on the diameter hose). Operating temperature: od -50°C up to +180°C.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsA fitting 90° ORFS INTERLOCK with a female UNF thread, sealing flat, for hose type 4SH, R13 and R15. Material: steel carbon, galvanized.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsA fitting BANJO angled 90° type RBR, Intended for hoses low-pressure rubber and plastic unreinforced and of reinforcement textile, with external a braid steel. used commonly in flexible lines for fittings sanitary, installation fuel, air etc. Material: steel carbon, galvanized.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsA fitting straight for hose, type NA with thread external BSPT and metric. intended for use in systems control, in installations for transport gases and liquids, in installations vacuum, etc. Working pressure: up to 10 bar. Material: polyamide (PA6).
Select options This product has multiple variants. The options may be chosen on the product page / DetailsPlug VB for fittings transfer TW (tankwagen). used for parts MK (female), constitutes a cap resistant on pressure. Material: brass. Operating temperature: od -20°C up to +65°C.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery strong, thick, flexible hose intended for extraction and conveying abrasive bulk materials: granulates, grain, sand, gravel. thick wall and very dense spiral reinforcing ensures high resistance to pressure and vacuum. very smooth inside, non-compressible, not very pliable (r=4xD), retains its flexibility also in low temperatures. hose o sound resistance to abrasion, resistant also on oils and gasoline. Assembly on connectors with bridge clamps (prawo-handed) or assembly special on ends industrial e.g. flange. Other diameters may be available on special order. versions: P3 S PU – version standard, with polyester – polyurethane, very resistant to abrasion and P3 S PU AE - version with polyether – polyurethane, o sound resistance to abrasion, resistant to microbes and hydrolysis; with approval for contact with substances food, compliant with requirements European 1935/2004/EC and 10/2011/EU (simulant E), 2023/2006/EC (GMP) and American FDA 21 CFR 177.2600 and 178.2010. is suitable for time contact with food at conveying dry, bulk, free of fat on surface, substances food - on conditions defined in declaration conformity the manufacturer (Available in Tubes International); P3 S PU AS – version antistatic (R ≤10 8 Ω), compliant with TRBS 2153 and for extraction also with TRGS 727, with polyether – polyurethane, o sound resistance to abrasion, resistant to microbes and hydrolysis. Hose material: transparent polyester-polyurethane (P3 S PU), transparent polyether-polyurethane (P3 S PU AE and P3 S PU AS). Wall thickness measured between the spiral: 2 mm. Reinforcement: dense spiral with wire steel. Operating temperature: od -40°C up to +100°C.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsA DIN 3015 standard clamp, type 101 (with a top plate) Intended for fast, easy, durable and aesthetic fastening pipes, cables and hoses in various branches industry, in installations above-ground and marine. made in accordance with the standard DIN 3015. assembly clamp for the structure performed is using welding base clamp (exists possibility screwing or mounting on a rail). standard A clamp has profiled (grooved) surface hole for a pipe. Available is also A clamp with smooth surface hole, Intended for hoses and cables, marked with the letter H on the end index. Dla group dimension 0 occurs one bolt with a hexagonal head, for group dimension 1 ÷ 6 available two screws with a hexagonal head. besides standard element metal can order: plates extension, rail and screws for mounting sets clamps. selection element should consulted with TUBES INTERNATIONAL®. Material clamp: aluminum. Material bolts: steel galvanized. Material plate: steel galvanized. Material base: steel carbon. Operating temperature: up to +350°C.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsA clamp tubular type UNI-FLEX S Intended for connecting and repairs pipes metal and plastic (connection axially not fixed, flexible - only with gasket rubber). Application: water, gaz, oils and fuels, other carbon, air. version material: steel AISI 316Ti (housing, screws - Class A4-80, solid pins). sealing: NBR rubber. Operating temperature: od -20°C up to +80°C. pressure nominal: PN 16 (Class pressure working for applications in industry shipbuilding, marine; Safety factor 4:1, assuming positive result single-use testing pressure four times greater, ale po which A clamp not can be used again). maximum Working pressure: 25 bar (for remaining applications industrial and conditions static; factor safety 1.5:1, assuming positive result testing pressure 150% maximum pressure working, po which A clamp can be further repeatedly used). value pressures working apply for mounting clamps on round tubes steel o minimum wall thickness wall, mounting in accordance with instructions and tightening a wrench torque given on a clamp torque).
Select options This product has multiple variants. The options may be chosen on the product page / DetailsAn AKBO HEAVY DUTY water gun. Made of stainless steel, insulated trigger, EPDM rubber guards, Viton seals. It has an adjustable outlet nozzle, smooth flow regulation and a trigger lock. Connection: 1/2" BSP female. The version with a trigger guard bow protects against uncontrolled opening of the water stream and against damage. maximum Working pressure: 24 bar. Maximum Operating temperature: +95°C. weight: ok. 0.87 kg. Flow rate: 30 l/min (5 bar), 75 l/min (24 bar).
Select options This product has multiple variants. The options may be chosen on the product page / DetailsPump displacement toothed (hydraulic), TRALE, o meshing external, Intended for use in systems hydraulic machine and equipment. Connections: flange. direction revolutions: right. given maximum pressure working refers to use continuous. Material: body and plate mounting – aluminum, Cover rear – aluminum. sealing: NBR. medium: oil hydraulic type L-HM45 or replacement. viscosity liquids: from 10 cSt to 600 cSt (recommended 30 ÷ 45). Operating temperature: od -20°C up to +90°C (medium), od -20°C up to +60°C (ambient).
Select options This product has multiple variants. The options may be chosen on the product page / DetailsButton flat monostable VRM-010 RN for valve VME. Do mounting required is Adapter VME1-000.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsReducer symmetrical (reducer concentric) for welding butt for applications pressure made with pipes seamless, compliant with the standard EN 10253-2B (steel carbon). With an EN 10204 3.1 material certificate. used commonly in industry in construction installation and pipelines, as element complete welded ends for hoses metal and rubber (welded with fitting threaded and flanged) and other fittings and element fittings. on request available also other sizes and materials, in this reducers o more than two sizes DN and reducers ASME. fittings type B (EN 10253-2B) have full strength pressure corresponding pipe o such same diameter D and wall thickness wall T. On special order available are other types fittings for welding-on butt: elbow 45° and 180°, reducers eccentric, tees, caps. Material: steel carbon P235 GH. Working pressure: od 71 up to 224 bar - depending on the diameter.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsRing clamping EAR CLIP-W is improved solution ring EARCLIP. has inner an insert protecting, which role is protection surface hose in space crimp ring and ensuring more even clamping po circuit. recommended for hoses o delicate construction. rounded edges inside ring protect hose against damage. Material: galvanised carbon steel (ring main), steel stainless AISI 301 (insert).
Select options This product has multiple variants. The options may be chosen on the product page / DetailsTee "T" 2x female threadint internal BSP, 1xgwint external BSPT type A12, intended for connecting element pneumatics (in this hoses) of each other. tightness connections requires with rules use additional seals. W case thread tapered tape PTFE or sealant, in case thread parallel washers aluminum or copper. Material: brass nickel-plated. Working pressure: 60 bar.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsTee plug-in "T" adjustable with thread external, type R32, intended for connections lines and other element in systems pneumatic. easy and fast in use for repeated mounting without loss tightness po side mechanical and pneumatic. Material: brass nickel-plated. Working pressure: 16 bar. medium working: vacuum, air. Operating temperature: od -20°C up to +80°C. sealing: NBR.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsFerrule assembly crimped for thick-walled hoses for freon, type 2051A. Material: aluminum.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsKnown and proven od lat, light and soft hose with rubber natural o light brown color. easy for installation thanks to its softness (hardness 40° Shore – A), flexible and flexibility (Maximum extensibility 500%). has close properties for latex. resistant to abrasion, o sound resistance to acids and bases. used for liquids and gases, for many applications industrial e.g. dispensing and dosing soaps and detergents, products alcoholic and milk, laboratories. Sterilization steam 30 min. (1 bar, 141°C) or oxide ethylene. length full roll hose 50 m (od diameter internal 7 mm - 25 m). The given working pressure is determined relative to the bursting pressure at a safety factor of 1:5. Material: rubber natural (NR). Operating temperature: od -35°C up to +70°C (120°C for moist hot). temperature brittleness: -40°C. Hardness: 40° Shore (A). Density: 0.98 g/cm³. Note: The product is packaged in the Tubes International Clean Zone (CLEAN ROOM) in compliance with rigorous standards. Return of the product after opening the package is not possible.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsA device intended for cutting hydraulic hoses 1 and 2 braid for diameter internal 2” and 4 braid for diameter 1.1/4”. used in workshops and cars service. Maximum Diameter outer hose: 80 mm. Drive: three-phase motor 400V, 3kW or (different version devices) supply battery 12 / 24V 1.1 kW. speed rotational: 2880 obr/min. Standard cutting disc: Ø 300 x 3 x 50 mm – smooth (a toothed disc can be used). weight 45 kg. Possibility of connection to an extraction system (Ø 63 mm).
Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose suction-delivery intended for conveying products pharmaceutical, cosmetic, substances food, chemical (selection in accordance with rules acc. to chapter "hoses chemical"). Contains no plasticisers, phthalates or substances of animal origin. is characterized high strength thermal and mechanical. is excellent solution for industries processing demanding highest safety during transfer products o high purity. Layer outer resistant to abrasion, ozone and conditions atmospheric. has two copper cable ensuring continuity electrical between fitting hose. standards and requirements : 1) general EC 2002/95 (RoHS), EC 1907/2006 (REACH). 2) industry food, contact with food 1935/2004/EC and 2023/2006/EU (GMP). Layer inner compliant with 10/2011/EC, D.M. 21/03/73, FDA 21 CFR 177.1550. Layer outer compliant with FDA 21 CFR 177.2600, D.M. 21/03/73. 3) Pharmaceutical industry: USP CLASS VI (Layer inner). assembly : smooth ends with a spigot ("tail" into the hose) must be used, without sharp or high barbs that could cut or damage the MFA inner layer after clamping. The spigot diameter should be precisely matched to the hose diameter to ensure tightness. Assembly with clamping ferrules or shell clamps. Inner layer: smooth polymer fluorine MFA. Reinforcement: cord synthetic, steel spiral. Outer layer: smooth EPDM rubber. Working pressure: 10 bar. Vacuum: 0.9 bar. Operating temperature: -50°C up to +170°C (for greater chemicals).
Select options This product has multiple variants. The options may be chosen on the product page / DetailsHydraulic hose with a reduced outer diameter and mass and increased flexibility (COMPACT type). intended for most demanding applications. excellent resistance to pressure pulsating. thanks to special blend rubber Layer outer antistatic, highly flame-retardant (exceeds requirements MSHA), highly resistant to ozone, conditions weather, abrasion and radiation UV. has certificate MSHA. standards: EN 857-2SC, SAE 100R 16S, ISO 11237-1. Assembly: contact TUBES INTERNATIONAL®. Inner layer: black synthetic rubber. Reinforcement: a double steel braid. Outer layer: black synthetic rubber. Working pressure: from 210 bar to 400 bar depending on the diameter hose. Operating temperature: od -40°C up to +100°C (momentarily up to +125°C).
Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose delivery intended for conveying compressed air, for compressors, hammers, drills and other tools pneumatic. thanks to low weight, flexibility, strong construction and high pressure working accepted and with success used od many lat in construction (in particular in companies occupying demolition), industry and mining. extremely strength and durable thanks to high quality materials and the structure. Reinforcement with circumferentially woven braid polyester completely bonded and surrounded rubber in original process production extrusion blend rubber on hot through braid. resistant to radiation UV. Layer inner smooth, co ensures minimal losses flow. yellow, grooved surface outer is resistant abrasion, oils and ozone and perfectly visible on square construction. flat at rest, co facilitates operation and storage. resistant to loads longitudinal. used most often of couplings claw for air (spacing 42 or 41 mm) mounted clamps cast iron (ordered separately). Available also in color black. use for air under high pressure should be always preceded analysis risk in situation accidental disconnection or bursting hose and possible use protections. maximum pressure working fixed acc. to coefficient safety 4:1 approved through the manufacturer for air. Not recommended exceeding 1/3 given force breaking. length standard roll: 200 m. Hose material: yellow blend NBR/PVC with barrier resistant on UV, pressed in a polyester braid in process extrusion hose. Working pressure: from 12.5 bar to 25 bar - depending on the diameter hose and temperatures. Operating temperature: od -30°C up to +75°C (momentarily up to +80°C).
Select options This product has multiple variants. The options may be chosen on the product page / DetailsMulti-hose in outer cover with black polyurethane, intended for installation pneumatic, hydraulic, oil, fuel, lubrication and chemicals. various color hoses enable easy identification individual circuits supply or various media. amount hoses: 2. Hose material: polyamide PA 12 (nylon). Working pressure: from 7.5 bar to 33 bar (in dependence od diameter and wall thickness wall hose). Operating temperature: od -20°C up to +80°C (for liquids containing water up to +65°C).
Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible metal hose of steel stainless intended for discharge gases with particles liquids, fumes, vapours, conveying dry bulk materials (ash, dusts, grain, granulates), and as hose cover. mounted in installations outlet exhaust gases engines as element absorbing vibration, noise and reducing effects expansion thermal. version standard stays shape. letter F on the end index means version FLOPPY, not maintaining shape. Material: steel AISI 304. Operating temperature: up to +650°C.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, flexible, popular hose, PVC general use. used for air, water and light chemicals in industry, agriculture, horticulture and for use domestic. Roll length: 60 m. Inner layer: transparent PVC. Reinforcement: a polyester braid. Outer layer: transparent PVC. Working pressure at a temperature of 20°C: from 10 bar to 15 bar - depending on the diameter hose and decreases together with of increase temperatures. Operating temperature: od -5°C up to +50°C.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsHanger intended for easy storage hose 1/2" (20 meters) or 3/4" (20 meters). raises comfort use and increases service life hose. convenience and saving space. Material: electropolished steel AISI 304.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsCap two-part coupling/valve IBC with a thread internal S60x6, with a removable cap in red; it can be used for screwing on e.g. a spout. Material: polypropylene.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsSocket cap coupling CAMLOCK DP made in accordance with the American military standard MIL-C-27487 (A-A-59326). Working pressure: up to 10 bar, depending on the coupling size. Material: steel AISI 316.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsCap (plug) ORFS with thread internal UNF (sealing on surface face), type VKA. Material: steel carbon, galvanized.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsCap for use in pipe installations industrial. Material: malleable cast iron. Operating temperature: up to +300°C. Working pressure: 25 bar (up to +120°C), 20 bar (up to +300°C).
Select options This product has multiple variants. The options may be chosen on the product page / DetailsCap fitting for system SPEEDFIT used in installations compressed air. Material: plastic plastic. Working pressure: 10 bar (+23°C), 7 bar (+70°C). Operating temperature: od -20°C up to +70°C.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsA universal valve directional o control electric (solenoid valve), without a coil control, used most often for control operation actuators. can be mounted in lines, for a wall, directly for actuators or on block connection. Function 5/2 - five-way, two-position. Material: body valve - aluminum, spool - aluminum nickel-plated, sealing - NBR, Cover end - plastic plastic. Working pressure: up to 10 bar. Operating temperature: -10°C up to +60°C.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsValve FFP securing configuration hydraulic against loss oil in case sudden depressurisation installation (e.g. rupture line). W during normal use the system, valve allows on Flow rate oil in both directions. W situation sudden rise flow (e.g. rupture line), valve closes Flow rate oil in one direction. permissible direction flow: A → A1 (free), A1 → A (valve). Material: steel carbon, galvanized (body), hardened steel (valve). sealing: metal-metal. Operating temperature: od -30°C up to +100°C.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsSet for foam and washing: Gun NITO ERGO, tank 2.5 l (Available in various colors) on agent cleaning with injector for foam, a hose suction and set nozzles dosing, lance 17 cm with nozzle for washing. max. Working pressure: 10 bar. max. Operating temperature: +60°C.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsCoupling GUILLEMIN with thread internal BSP intended for installation industrial and transfer substances, bulk, granulates. Not is suitable for conveying steam and gases. coupling has symmetrical design parts connection. Made in accordance with the EN 14420-8/NF-E-29572 standard. Material: aluminum. Working pressure: 16 bar. sealing: white NBR rubber. Operating temperature: od -10°C up to +80°C.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsCoupling with thread external BSP, type VSLR, under a clamp shell with tail serrated EN 14420-3 / DIN 2817 (only clamp RS 636... and RS-637...) for mounting for hoses industrial - e.g. in use transfer. Working pressure: 25 bar. Coupling material: brass (MS), steel stainless AISI 316 (SS). sealing: flat (butt). Operating temperature: od -20°C up to +65°C acc. to EN-14420.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight A reel type COMPACT in housing plastic for operation in places, where required are small dimensions e.g. cars service, lines assembly, tables workbench, etc. equipped in hose polyurethane o length 12 m. Available to the standard with bracket swivel. hose main terminated additional spring anti-kink. Material housing: plastic plastic. Operating temperature: up to +50°C.



















































