- Home
- All products
Our products
Product categories
Working pressure [bar]
Minimum operating temperature [°C]
Maximum operating temperature [°C]
Material
Vacuum resistance
Standard length [m]
Select options This product has multiple variants. The options may be chosen on the product page / DetailsValve alloy series STP-B with thread internal is valve controlled pneumatic. allows on Flow rate air through valve po simultaneous applying pneumatic signal control (the pilot). W case loss signal control valve is closed in both directions flow. valve STP-B mounted in the connection supply actuator causes, at the absence pressure on the connection control (the pilot), stopping movement actuator. use valves STP-B as valves safety should be preceded appropriate analysis risk the system pneumatic or the entire devices. Working pressure: 0.5÷10 bar. Operating temperature: od -10°C up to +60°C. Body material: brass nickel-plated. sealing: NBR.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsSet FR + L series NEW DEAL o high degree reliability for heavy conditions use, with reducer type piston. is characterized stability pressure set at variable pressure supply, micrometric regulation doses lubrication proportional for flow air, guaranteed work at low values flow. Output pressure range: 0÷8, 0÷12 bar. Supply pressure: up to 18 bar, for trigger RA up to 10 bar. Operating temperature: up to +50°C. Connection: 1/4" BSP female, 3/8", 1/2". Connection pressure-gauge: 1/8" BSP female. Condensate drain: manual / semi-automatic (RMSA), automatic (SAC, RA). Flow rate: 500 l/min - 1/4", 2200 l/min - 3/8", 1/2" (at an inlet pressure of 6 bar Δp = 1 bar).
Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-pressure adapter type A203 with thread external BSP (sealing 60° cone) and with thread internal NPT (sealing on the thread). Material: steel AISI 316L.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsNozzle BLOWSTAR with double a nipple for guns for air, terminated thread metric M12x1.25. is characterized low level noise - only 74 dB at a pressure of 6 bar, not weakening force air blowing. meets the following standards safety and the directive: OSHA 1-13.1. (European Agency safety and Health in use), 2003/10/WE, 2006/42/WE, EN 12100. Flow rate nominal: 295 l/min at a pressure of 6 bar. Material: cast zinc (nozzle), aluminum (nipple).
Select options This product has multiple variants. The options may be chosen on the product page / DetailsFilter - reducer GAFR series GA with thread internal BSP serves for removing contaminants contained in compressed air in order to correct use element systems pneumatic, a set manually reducer stays constant value pressure at the outlet, independently od fluctuations pressure supply. W set found angle bracket/A handle assembly and pressure gauge. Do connecting individual element of each other, serve sets connecting GA (shape L, T, U). Size: 200, 300, 400, 600. Filtration grade: 40 µm. Supply pressure: up to 10 bar. Operating temperature: od -5°C up to +70°C. Connection: 1/8" BSP female ÷ 1". Condensate drain: automatic (A). Flow rate: 1050 l/min - size 200, 2250 l/min - size 300, 4000 l/min - size 400, 6500 l/min - size 600 (at an inlet pressure of 6 bar Δp = 1 bar).
Select options This product has multiple variants. The options may be chosen on the product page / DetailsSocket coupling CAMLOCK DU with a thread internal BSP (Flat gasket polyurethane) made in accordance with the American military standard MIL-C-27487 (A-A-59326), commonly used as a transfer coupling, especially in the petrochemical industry. Working pressure: up to 10 bar, depending on the coupling size. Material: aluminum. Levers: steel AISI 304 (in sizes 1.1/4" for 4" - Levers made of brass). Sealing: NBR.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsA fitting hydraulic screw, type S, with tube metric, sealing a ring cutting (BES), angled 45° series heavy. Intended for screwing in hoses rubber and thermoplastic using ferrule screw-together. Material: steel carbon, galvanized.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsA PUSH-ON JIC end with thread internal UNF, type YJW110, intended for a self-clamping hose designed for this type of end. Mounted onto the hose without the use of clamps or brackets. It has a special barb profile adapted to the material and dimensions of the PUSH-ON hose and the construction of its braid, causing the hose to clamp onto the barbs of the end. The end must not be used with other hoses or clamped with clamps or brackets, as this risks damaging the hose. Operating temperature: od -40°C up to +80°C. Working pressure in accordance with the specification of the PUSH-ON hose. Material: galvanised carbon steel, brass, AISI 316 steel.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsA nut DIN 8537/20033 with thread Rd Intended for tapered fittings with "tail" for hose. Material: cast iron galvanized. Working pressure: 16 bar.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsA clamp RUBBER P-CLIP compliant with the standard DIN 3016 recommended for safe and damping vibrations mounting pipes, hoses, bundles cables, corrugated pipes electrical-installation (cover on cables) etc., for which exists possibility abrasion and damage. A clamp this type found wide use, m.in.: machine agricultural and construction, design engines combustion, industry railway, equipment electric, equipment AGD etc. made is with one section bent tape steel and rubber flange. holes on obu ends tape are reinforced steel plates, co ensures strength on clamping at large loads mechanical. tape made of steel stainless AISI 304 (W4), profile with rubber EPDM resistant to water, abrasion, changes temperatures and aging. version W4 recommended for applications in industry marine. A clamp not contains screws, washer and a nut. Material: steel AISI 304 (tape), EPDM rubber (flange). Band width: 15 mm.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsPlate top protecting stacking for mounting clamp DIN 3015 standard type 100/101. Material: steel carbon, galvanized or steel AISI 304.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsFitting angled 90° adjustable JIC 37° with thread external NPT (sealing on the thread – PTFE tape or anaerobic sealant). Material: steel AISI 316.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsDirectional valve plug-in side, type R44, intended for connections lines and other element in systems pneumatic. easy and fast in use for repeated mounting without loss tightness po side mechanical and pneumatic. Material: plastic plastic. Working pressure: 12 bar. medium working: vacuum, air. Operating temperature: od -20°C up to +60°C. sealing: NBR.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong hose suction-delivery intended for conveying dry or liquid substances abrasive, granulates etc. externally Serrated, inside smooth. Layer inner with transparent, resistant to abrasion polyurethane, o wall thickness od 0.6 mm (DN30) for 1 mm (DN100). The hose has a copper wire arranged along the spiral which, after earthing or connection to an end, discharges electric charges. Widely used in processing plastics in use demanding greater resistance to abrasion, puncturing and cutting hose. especially recommended for regrind plastics o relatively sharp edges. Standards and requirements: Food industry, food contact: compliant with the European requirements 1935/2004/EC and 10/2011/EU (simulant fluids A, B and C), 2023/2006/EC (GMP) – refers to liquid substances food. Inner layer: transparent polyurethane. Outer layer: transparent PVC. Reinforcement: rigid-PVC spiral. Working pressure: from 3 bar to 5 bar, depending on the diameter hose and temperatures. Vacuum: for 0.7 bar. Operating temperature: -10°C up to +60°C.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong, flexible rubber hose fire-protection, adapted for use on drums. hose ANKARA EN made is according to standards EN 694 consists ofcej European standard for hoses for solid installation fire-protection and used commonly on drums in solid hydrants in buildings, installations industrial, centres commercial etc. Layer inner with rubber EPDM, resistant to light chemicals and fire-protection agents foam-forming. Layer outer with rubber EPDM resistant to abrasion and conditions atmospheric. perfectly works mounted on drums, ensuring Flow rate water at incomplete unrolling hose. presented hose ANKARA made is acc. to requirements older standards DIN 14817: 1991 intended for powder and foam agents firefighting, with layer inner with conductive rubber NR/SBR and o pressure working up to 20 bar, also adapted for use on drums. Inner layer: EPDM rubber (ANKARA EN), conductive rubber NR/SBR (ANKARA). Reinforcement: cord synthetic. Outer layer: EPDM rubber (ANKARA EN), rubber SBR (ANKARA). Working pressure: from 7 bar to 20 bar - depending on size and kinds hose. Operating temperature: od -20°C up to +60°C (ANKARA EN), od -40°C up to +70°C (ANKARA).
Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, pliable and flexible hose intended for extraction hot vapours, fumes, gases, dusts, discharge air cooling and air blowing. flame-retardant, resistant to temperature, radiation UV, ozone and aging. used we all fields industry for applications high-temperature, m.in. for extraction with furnaces in industry metallurgical, foundry, industry glass and ceramic. is characterized high compressibility, strong design resistant on vibration and stretching, resistance on impacts thanks to outer spiral. Other diameters are available on special order in the scope 50 ÷ 508 mm. Assembly of the hose on connectors with bridge clamps (lewo-handed). length standard: 3 m (on special order also sections 6 and 10 m). Hose material: fabric glass impregnated silicone (silver-grey), o wall thickness 0.4 mm. Reinforcement: outer spiral with wire and sheet steel galvanized. Operating temperature: od -60°C up to +300°C.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, flexible hose intended for oil installation hydraulic, fuels, liquids based on water. on request micro-perforated (for gases and air). Inner layer: polyester. Reinforcement: a steel braid. Outer layer: polyurethane. Working pressure: from 70 bar to 325 bar, depending on the diameter hose. Operating temperature: od -40°C up to +100°C (for water and air up to +70°C).
Select options This product has multiple variants. The options may be chosen on the product page / DetailsPlug water quick coupling NiTO CLICK 3/4" with thread internal. quick coupling NiTO CLICK to water quick coupling made according to profile very popular plastic quick couplings garden and compatible with them. sealing using an O-ring placed externally on plug. Manufactured in Denmark – 5-year warranty. They retain the simplicity of the commonly known plastic quick couplings and are characterized by strength and durability. intended for water, water of agents cleaning for use in industry, services, horticulture, agriculture etc. Material: brass chrome-plated (matte - satin). Working pressure: up to 25 bar. Operating temperature: od -30°C up to +80°C. sealing: NBR (not is suitable for gasolines and oils).
Select options This product has multiple variants. The options may be chosen on the product page / DetailsValve fast trigger serves for increasing speed actuator through fast discharge air. Body material: brass nickel-plated. Material cover: brass nickel-plated (1/8" ÷ 1/4"), aluminum anodized (1/2"). gasket flat: NBR. gasket lip: polyurethane. maximum pressure: 12 bar. minimal pressure: 0.5 bar. Operating temperature: od 0°C up to +80°C.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsA LET-LOK® 90° fitting for a metric tube Intended mainly for industry chemical, petrochemical, pharmaceutical, power generation, nuclear power plants and process engineering. The permissible pressure working specifies on the basis of diameter outer and wall thickness wall tubes (details in the attachment). Material: steel AISI 316.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsHydraulic high-pressure adapter, in shape elbow bent under angle 90°, with thread external BSP (sealing 60° cone) and with thread internal BSP, with a nut swivel (sealing 60° cone). elbow bent is used in order to more efficient flow medium. Material: steel carbon, galvanized.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsAdapter DIN 20037 with thread external BSP and Rd, for use in installation pneumatic. Material: steel/cast iron galvanized. Working pressure: 25 bar.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh quality Adapter reducing for quick couplings NiTO for water with thread internal and thread external. Material: brass chrome-plated. Working pressure: up to 25 bar. Operating temperature: up to +80°C. sealing: NBR (not is suitable for gasolines and oils).
Select options This product has multiple variants. The options may be chosen on the product page / DetailsFilter FIL series SKILLAIR®, without plates end, serves for accurate removal contaminants liquid and solid, contained in compressed air. Size: 400. Filtration grade: 5 µm, 20 µm, 50 µm. Supply pressure: up to 13 bar, depending on kinds trigger. Operating temperature: up to +50°C. Connection: 1" BSP female ÷ 2". Condensate drain: manual / semi-automatic (RMSA), automatic (RA).
Select options This product has multiple variants. The options may be chosen on the product page / DetailsA fitting rubber for nozzle o diameter outer 6 mm (compatible with nozzle under index EW-470K12), protecting against scratches cleaned delicate surfaces. Material: TPU.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsA fitting hydraulic screw, type S, with a female BSP thread with a nut, cone sealing 60° (DKR), angled 90°. Intended for screwing in hoses rubber and thermoplastic using ferrule screw-together. Material: steel carbon, galvanized.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsA PUSH-ON end with thread internal BSP (sealing 60° cone), type YBW110, intended for a self-clamping hose designed for this type of end. Mounted onto the hose without the use of clamps or brackets. It has a special barb profile adapted to the material and dimensions of the PUSH-ON hose and the construction of its braid, causing the hose to clamp onto the barbs of the end. The end must not be used with other hoses or clamped with clamps or brackets, as this risks damaging the hose. Operating temperature: od -40°C up to +80°C. Working pressure in accordance with the specification of the PUSH-ON hose. Material: galvanised carbon steel, brass, AISI 316 steel.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsPlug JIC 37° with thread internal UNF (sealing on cone internal 37°). Material: steel AISI 316.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsA clamp RUBBER P-CLIP compliant with the standard DIN 3016 recommended for safe and damping vibrations mounting pipes, hoses, bundles cables, corrugated pipes electrical-installation (cover on cables) etc., for which exists possibility abrasion and damage. A clamp this type found wide use, m.in.: machine agricultural and construction, design engines combustion, industry railway, equipment electric, equipment AGD etc. made is with one section bent tape steel and rubber flange. holes on obu ends tape are reinforced steel plates, co ensures strength on clamping at large loads mechanical. tape made of carbon steel galvanized (W1), profile with rubber EPDM resistant to water, abrasion, changes temperatures and aging. A clamp not contains screws, washer and a nut. Material: steel carbon, galvanized (tape), EPDM rubber (flange). Band width: 12 mm.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsPlate bottom double for welding for mounting clamps DIN 3015 standard type 100/101. number clamps: 2. Dla group dimension 0 occurs one hole under bolt. Dla group dimension 1 ÷ 6 available two holes under bolt. Material: steel carbon or steel AISI 316L.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsDirectional valve spool, type 4/2, Controlled electrically of centering springs intended for mounting plate. used in systems hydraulic machine industrial. standard supplied with o-rings and screws mounting. A connector equipped is in diode signalling state supply. Material: cast iron (body), hardened steel (spool). sealing: NBR. maximum Working pressure: 315 bar (channels P,A,B), 160 bar (channel T). available on the following voltage control: 12 V DC, 24 V DC, 110 V AC or 220 V AC. Operating temperature: od -20°C up to +80°C.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsCoupling push-in Tee "T" of couplings push-in for hose o diameter inch, series S, type PUTC. economical solution for connecting flexible hoses pneumatic o inch calibrated diameter outer. easy and fast in use. Material: plastic plastic. Working pressure: 10 bar. Vacuum: 0.99 bar. Operating temperature: od 0°C up to +60°C. sealing: NBR.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsRectangularly Serrated hose reinforced spiral steel, for hot water and liquids anti-freeze, intended for automotive and industrial systems cooling. has resistance to vacuum. Layer inner resistant to heat and fluids cooling. Layer outer resistant to overheating, oil and aging. Inner layer: black rubber CR. Reinforcement: cord synthetic, steel spiral. Outer layer: black rubber CR. Working pressure: up to 4 bar. Operating temperature: od -40°C up to +100°C.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsThree-layer hose suction o specific the structure intended for discharge very hot (up to 1100°C) gases, vapours, fumes and air. outer Layer impregnated fabric glass with threads of steel stainless ensures strength mechanical, central thick fabric high-temperature fully role insulating, inner very fine mesh of steel stainless separates Flow rate hot gases. Flame-retardant, to some extent resistant to hot sparks. used at furnaces and engines for extraction gases o very high temperature, in industry metallurgical, ceramic, shipbuilding, aviation, automotive and equipment military. hose o strong the structure and resistance to impacts thanks to outer spiral. Used only as a suction hose working under vacuum, due to the possibility of gases penetrating outwards under overpressure (degassing). hoses o small diameter internal < 100 mm are characterized tzw. two-hose design (Layer inner with mesh constitutes separate hose of spiral). Assembly of the hose on connectors with bridge clamps (lewo-handed). length standard: od 2 for 10 m - depending on the diameter. Hose material: 3 layer: externally impregnated fabric glass with fibres of steel stainless (grey), central Layer - high-temperature fabric insulating, inside fine mesh - steel stainless. Reinforcement: outer spiral with wire and sheet of steel stainless. Operating temperature: od -50°C up to +1100°C.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, flexible hose intended for solvents, paints, isocyanate, polyol, liquids based on water. is suitable for use in environment high humidity and salty air. on request micro-perforated (for gases and air). Inner layer: polyamide. Reinforcement: an aramid braid + a steel braid. Outer layer: polyurethane. Working pressure: from 200 bar to 500 bar, depending on the diameter hose. Operating temperature: od -40°C up to +100°C (for water and air up to +70°C).
Select options This product has multiple variants. The options may be chosen on the product page / DetailsPlug coupling CAMLOCK F with a BSPT male thread made in accordance with the American military standard MIL-C-27487 (A-A-59326), commonly used as a transfer coupling, especially in the petrochemical industry. Working pressure: up to 10 bar, depending on the coupling size. Material: brass.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose delivery for sandblasting extremely resistant to abrasion. thick Layer inner with rubber o exceptionally sound resistance to abrasion (40±5 mm 3 acc. to ISO 4649 / DIN 53516). exceeds requirements standards ISO 3861:2008. The antistatic inner and outer layer prevents the accumulation of electric charges. Used for strongly abrasive materials such as quartz sand, steel shot, corundum, glass in abrasive blast treatment of steel structures, castings, concrete surfaces, etc.. Mounted with special sandblasting ends. length standard: 60 m / 40 m for diameter 16 mm (or 120 m - contact with Tubes International). Inner layer: black rubber NR/SBR. Reinforcement: cord synthetic. Outer layer: black synthetic rubber. Working pressure: 12 bar. Operating temperature: od -40°C up to +80°C.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsA universal valve directional o control manual, a lever front, used most often for control operation actuators. can be mounted in lines, for a wall, directly for actuators or on block connection. Function 5/3 - five-way, three-position. Size: 1/8". Material: body valve - aluminum, spool - aluminum nickel-plated, sealing - NBR, Cover end - plastic plastic. Working pressure: up to 10 bar. Operating temperature: -10°C up to +60°C.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsCoupling Tee type LET-LOK® for connections tubes inch, Intended mainly for industry chemical, petrochemical, pharmaceutical, power generation, nuclear power plants and process engineering. The permissible pressure working specifies on the basis of diameter outer and wall thickness wall tubes (details in the attachment). Material: steel AISI 316.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-pressure adapter with thread external BSP (sealing 60° cone) and with thread internal BSP (sealing 60° cone), with a nut swivel. used is in installations hydraulics power for connecting hydraulic lines flexible and pipes with other element installation (pump, valves, quick coupling etc.). allows reduction kinds and size, compliant with connections joined element. Material: steel carbon, galvanized.


















































