Our products
Product categories
Working pressure [bar]
Minimum operating temperature [°C]
Maximum operating temperature [°C]
Material
Vacuum resistance
Standard length [m]
Select options This product has multiple variants. The options may be chosen on the product page / DetailsPlug quick coupling CEJN 115 with thread internal and with valve intended for installation hydraulic o very high pressures. used in presses hydraulic, equipment rescue, jacks hydraulic, cutters, etc. supplied standard with a cap in order to protection against contaminants. Material: hardened steel, galvanized. sealing: NBR. Flow rate: 6 l/min (Δp = 4 bar). Diameter nominal: 2.5 mm. Working pressure: 1000 bar (coupling connected). pressure bursting: 2600 bar. Operating temperature: od -30°C up to +100°C.- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh quality two-way ball valve with threads internal BSP and holes mounting in body, intended for high-pressure installation hydraulic. Material: steel (body, ball, stem). seal: POM (ball), NBR (stem). Operating temperature: od -40°C up to +100°C (POM); od -40°C up to +100°C (NBR).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsValve overflow VMPP limiting maximum pressure oil in systems hydraulic. allows free Flow rate liquids between connections P. W moment rise pressure over set value, occurs opening ways T and outflow excess oil for bowl. value pressure opening sets using screws (setting a wrench Allen, lock a lock nut). valve equipped in Connection pressure-gauge (1/4" BSP female) and holes assembly. Material body: steel galvanized. Material valve: steel galvanized. sealing: NBR. maximum Working pressure: 400 bar. Operating temperature: od -20°C up to +90°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsValve check Controlled (lock hydraulic) type FPD used in systems hydraulic as element securing against uncontrolled movement actuator double-acting operation (retraction / extension piston rod). The permissible directions flow: V1 → C1 (and simultaneously C2 → V2), V2 → C2 (and simultaneously C1 → V1). Material: steel galvanized (body), hardened steel (stem). sealing: NBR. pressure opening: 3 bar, for size thread 3/4" - 0.5 bar. Operating temperature: od -20°C up to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsValve check Controlled type FPDL used in systems hydraulic as element securing against uncontrolled movement actuator double-acting operation (retraction / extension piston rod). The permissible directions flow: V1 → C1 (and simultaneously C2 → V2), V2 → C2 (and simultaneously C1 → V1). valve equipped in 2 holes assembly shown on photo. Material: body - steel galvanized (1/4", 3/8"), aluminum (1/2", 3/4"); stem - hardened steel. sealing: NBR. pressure opening: 3 bar. Operating temperature: od -20°C up to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA fitting straight NON SKIVE with a female metric thread, with seal on cone 24°, O-ring (DKOS), series heavy, Intended for crimping in hoses type 4SP, 4SH, R13 and R15 using ferrule crimping TI-N.... assembly: without skiving rubber hose. Material: steel carbon, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA clamp DIN 3015 heavy type 201 (with a top plate) Intended for fast, easy, durable and aesthetic fastening pipes, cables and hoses in various branches industry, in installations above-ground and marine. made in accordance with the standard DIN 3015. assembly clamp for the structure performed is using welding base clamp (exists possibility screwing or mounting on a rail). standard A clamp has profiled (grooved) surface hole for a pipe. besides standard element metal can order: plates extension, rail and screws for mounting sets clamps. selection element should consulted with TUBES INTERNATIONAL®. Material clamp: green polypropylene. Material bolts: steel galvanized. Material plate: steel galvanized. Material base: steel carbon. Operating temperature: od -30°C up to +90°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPin STECKO as element securing connection plug and socket. Material: steel free-cutting, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSleeve crimping IL13 for hoses hydraulic rubber with a braid spiral type R13 and R15. Use only with fitting hydraulic INTERLOCK od this the same supplier. assembly - skiving external and internal. Diameter D1 - Diameter outer. Diameter D2 - Diameter inner. Diameter D3 - Diameter lock. Material: steel carbon, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA general-purpose hydraulic hose with increased service life relative to the standard. Confirmed hose service life of 300.000 pulse cycles. standards: EN 853 1SN, ISO 1436-1SN, SAE 100R1S-AT. Inner layer: black, oil-resistant synthetic rubber. Reinforcement: a single steel braid. Outer layer: black, oil-resistant synthetic rubber. Working pressure: from 40 bar to 250 bar depending on the diameter hose. Operating temperature: od -40°C up to +100°C (momentarily +120°C). For water and air, the maximum working temperature is +70°C. For air above 17 bar, microperforation of the outer layer is required.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPlug screw-together PVS quick coupling hydraulic intended for installation o very high pressures, in which available large loads mechanical. used in presses hydraulic, equipment rescue, jacks hydraulic, cutters, etc. can be joined / disconnected when in system found pressure residual. caps should order separately. Material: steel carbon. sealing: NBR. Flow rate: 1/4" - 16.4 l/min; (Δp = 4 bar), 3/8" - 21.3 l/min; (Δp=4 bar). Working pressure: 700 bar. pressure bursting: 1/4" - 2100 bar (coupling connected), 3/8" - 1850 bar (coupling connected), 1/4" - 1490 bar (plug disconnected), 3/8" - 1500 bar (plug disconnected). Operating temperature: od -25°C up to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFour-way ball valve "X" type MKHX with thread internal BSP, intended for high-pressure installation hydraulic. standard equipped in holes assembly. Material: steel (body, ball, stem). seal: POM (ball), NBR (stem). Operating temperature: od -40°C up to +100°C (POM); od -20°C up to +100°C (NBR).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsValve overflow VM30 limiting maximum pressure oil in systems hydraulic. allows free Flow rate liquids between connections P. W moment rise pressure over set value, occurs opening ways T and outflow excess oil for bowl. value pressure opening sets using screws (setting a wrench Allen, lock a lock nut). valve equipped in holes assembly. Material body: steel galvanized (1/4"), aluminum (3/8" and 1/2"). Material valve: steel galvanized. sealing: NBR. maximum Working pressure: 350 bar (1/4"), 260 bar (3/8" and 1/2"). Operating temperature: od -20°C up to +90°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsElbow socket-push-in STECKO for use in systems hydraulic for mining. Material: steel free-cutting, galvanized. sealing: NBR (O-ring), teflon (ring thrust).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA fitting flange 45° NON SKIVE SAE 3000 (SFL 45), series light, Intended for crimping in hoses type 4SP, 4SH, R13 and R15 using ferrule crimping TI-N.... assembly: without skiving rubber hose. Material: steel carbon, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA fitting flange 90° INTERLOCK SUPERCAT, sealing O-ring or different gasket in groove flange, for hose type 4SH, R13 and R15. Material: steel carbon, galvanized.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsReady, complete line high-pressure, based on hose VIPER, intended for tools hydraulic 700 bar, such as spreaders, shears, balancers for doors, keys czy lifts, in color yellow phosphorescent, well visible in weak conditions lighting. equipped is in limiters deflection hose za ferrules. line is tested pressure and supplied of appropriate certificate. Inner layer: polyamide. Reinforcement: high-strength, multilayer a steel braid. Outer layer: yellow phosphorescent polyurethane. Material fittings and ferrule: steel carbon, galvanized. Working pressure: up to 700 bar. Operating temperature: od -30°C up to +60°C.- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA rail Intended for mounting clamp DIN 3015 heavy type 201 using a nut ADESP. shipping in sections 2 m. Material: steel carbon or steel AISI 304.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA general-purpose hydraulic hose. used for installation o lower pressures. It is characterised by high flexibility and lightness. standards: EN 854 2TE. Inner layer: black, oil-resistant synthetic rubber. Reinforcement: a single textile braid. Outer layer: black, oil-resistant synthetic rubber. Working pressure: from 40 bar to 80 bar (depending on the diameter hose). Operating temperature: od -40°C up to +100°C. For water and air, the maximum working temperature is +70°C. For air above 17 bar, microperforation of the outer layer is required.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh quality three-way ball valve type "L" with threads internal BSP and holes mounting in body, intended for high-pressure installation hydraulic. Material: steel (body, ball, stem). seal: POM (ball), NBR (stem). Operating temperature: od -40°C up to +100°C (POM); od -20°C up to +100°C (NBR).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsValve overflow VM80 limiting maximum pressure oil in systems hydraulic. allows free Flow rate liquids between connections P. W moment rise pressure over set value, occurs opening ways T and outflow excess oil for bowl. value pressure opening sets using screws (setting a wrench Allen, lock a lock nut). valve equipped in holes assembly. Material body: aluminum. Material valve: steel galvanized. sealing: NBR. maximum Working pressure: 260 bar. Operating temperature: od -20°C up to +90°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsValve FPS allows free Flow rate liquids hydraulic in one direction (A → A1) and opening flow liquids in direction opposite (A1 → A) under a condition supply pressure signal control "X". standard pressure opening flow free (A → A1) 0.5 bar. required pressure signal control "X" for opening flow in direction opposite (A1 → A) determined is through product coefficient actuation and pressure po side A1. Material: steel galvanized (body), hardened steel (stem). sealing: NBR. Operating temperature: od -20°C up to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsValves check type VNRO / VNROHP intended for closing flow liquids hydraulic in one direction and opening free flow liquids in direction opposite. standard pressure opening 1 bar (available also with other pressure opening from 0.2 bar to 6 bar). permissible direction flow: A → A1. valves type VNROHP equipped are in additional ring sealing allowing on operation at maintaining higher coefficient safety. Material body and stem: steel carbon with coating zinc - nickel, steel stainless AISI 316Ti. sealing: NBR - steel carbon, Viton (FPM) - steel stainless. Operating temperature: od -35°C up to +100°C (NBR); od -20°C up to +200°C (Viton).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA fitting banjo Intended for mounting using soldering on tubes metric made of carbon steel. A fitting has hole D matched for diameter outer tubes. version with a hole banjo F matched for screws with thread metric. Material ends: steel carbon raw (without galvanizing). in order to selection material soldering and technology soldering please o contact with Tubes International.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA fitting flange straight INTERLOCK SUPERCAT, sealing O-ring or different gasket in groove flange, for hose type 4SH, R13 and R15. Material: steel carbon, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA fitting straight NON SKIVE with a thread external metric, with seal on cone 24°, O-ring (CES), series heavy, Intended for crimping in hoses type 4SP, 4SH, R13 and R15 using ferrule crimping TI-N.... assembly: without skiving rubber hose. Material: steel carbon, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA DIN 3015 double clamp, type 301 (with a top plate) Intended for fast, easy, durable and aesthetic fastening pipes, cables and hoses in various branches industry, in installations above-ground and marine. made in accordance with the standard DIN 3015. assembly clamp for the structure performed is using welding base clamp (exists possibility screwing or mounting on a rail). standard A clamp has profiled (grooved) surface hole for a pipe. Available is also A clamp with smooth surface hole, Intended for hoses and cables, marked with the letter H on the end index. besides standard element metal can order: plates extension, rail and screws for mounting sets clamps. selection element should consulted with TUBES INTERNATIONAL®. Material clamp: green polypropylene. Material bolts: steel galvanized. Material plate: steel galvanized. Material base: steel carbon. Operating temperature: od -30°C up to +90°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA general-purpose hydraulic hose. Increased hose service life relative to the standard, confirmed by a test of 1.000.000 pulse cycles. Flame-retardant outer layer (MSHA). standards: EN 856 4SH, ISO 3862-1 4SH. Inner layer: black, oil-resistant synthetic rubber. Reinforcement: four layers of steel wire. Outer layer: black, oil-resistant synthetic rubber. Working pressure: from 250 bar to 420 bar depending on the diameter hose. Operating temperature: od -40°C up to +100°C (momentarily +120°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh quality three-way ball valve "L" type BK3L with thread internal NPT, intended for high-pressure installation hydraulic. Material: steel (body, ball, stem). seal: POM (ball), NBR (stem). Operating temperature: od -40°C up to +100°C (POM); od -20°C up to +100°C (NBR).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsValve overflow VM45 limiting maximum pressure oil in systems hydraulic. allows free Flow rate liquids between connections P. W moment rise pressure over set value, occurs opening ways T and outflow excess oil for bowl. value pressure opening sets using screws (setting a wrench Allen, lock a lock nut). valve equipped in holes assembly. Material body: aluminum. Material valve: steel galvanized. sealing: NBR. maximum Working pressure: 260 bar. Operating temperature: od -20°C up to +90°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCoupling socket system STECKO for use in systems hydraulic for mining. Material: steel free-cutting, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSocket bolted HPA quick coupling hydraulic intended for installation o very high pressures, in which available large loads mechanical. used in presses hydraulic, equipment rescue, jacks hydraulic, cutters, etc. can be joined / disconnected when in system found pressure residual. caps should order separately. Material: steel carbon. sealing: NBR. Flow rate: 1/4" - 16.4 l/min; (Δp=4 bar), 3/8" - 21.3 l/min; (Δp = 4 bar). Working pressure: 700 bar. pressure bursting: 1/4" - 2100 bar (coupling connected), 3/8" - 1850 bar (coupling connected), 1/4" - 1800 bar (socket disconnected), 3/8" - 1850 bar (socket disconnected). Operating temperature: od -25°C up to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsClip protecting serves for securing coupling connected (plug with socket SKV) during manoeuvring or carrying lines connected against ich disconnection. Diameter D - Diameter po outside. Material: steel galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA fitting banjo Intended for mounting using soldering on tubes metric made of carbon steel. A fitting has hole D matched for diameter outer tubes. version with a hole banjo F matched for screws with thread inch. Material ends: steel carbon raw (without galvanizing). in order to selection material soldering and technology soldering please o contact with Tubes International.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA fitting flange 90° INTERLOCK SAE 6000, sealing O-ring or different gasket in groove flange, for hose type 4SH, R13 and R15. Material: steel carbon, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA fitting flange straight NON SKIVE SAE 6000 (SFS), series heavy, Intended for crimping in hoses type 4SP, 4SH, R13 and R15 using ferrule crimping TI-N.... assembly: without skiving rubber hose. Material: steel carbon, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA nut with thread metric Intended for mounting clamp DIN 3015 standard type 100/101 and clamp DIN 3015 double type 201 on a rail ABINS. Material: alloy zinc with aluminum.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsReady, flexible, four-braid line high-pressure, used mainly for tensioning bolts, cutting water, for lifts, wrenches and other equipment hydraulic. line is tested pressure and supplied of appropriate certificate. meets standard EN 1829-2. Inner layer: POM (polyoxymethylene). Reinforcement: four braids with highly strength wire steel. Outer layer: PA (polyamide). Material fittings and ferrule: steel carbon, galvanized. Working pressure: up to 1800 bar. Operating temperature: od -30°C up to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHydraulic hose for applications in mining. Layer outer antistatic, non-toxic resistant to flame. has certificate confirming meeting requirements safety in Zone at-risk explosion. standards: EN 856 4SP, ISO 3862-1 4SP. Inner layer: black synthetic rubber. Reinforcement: four layer spiral wire steel. Outer layer: black synthetic rubber. Working pressure: from 210 bar to 445 bar depending on the diameter hose. Operating temperature: od -40°C up to +100°C (momentarily up to +120°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh quality two-way ball valve type BKH L/S with external thread metric, DIN 2353, intended for high-pressure installation hydraulic. occurs as: L (series light), S (series heavy). Material: steel (body, ball, stem). seal: PA (ball), NBR (stem). Operating temperature: od -40°C up to +100°C (PA): od -20°C up to +100°C (NBR).
