Our products
Select options This product has multiple variants. The options may be chosen on the product page / DetailsConnection tube angled 90°, for connections using ring and a nut DIN 2353 and fitting Intended for hose measurement. Connection occurs as: L (series light) and S (series heavy), A fitting whereas Intended is for hoses DN2 or DN4 and supplied in set with a clamping ferrule. pressure working dependent od the connection mounted for tube and pressure working hose. Material: steel with coating zinc-nickel.- Select options This product has multiple variants. The options may be chosen on the product page / DetailsConnection tube straight, for connections using ring and a nut DIN 2353 and fitting Intended for hose measurement. Connection occurs as: L (series light) and S (series heavy), A fitting whereas Intended is for hoses DN2 or DN4 and supplied in set with a clamping ferrule. pressure working dependent od the connection mounted for tube and pressure working hose. Material: steel with coating zinc-nickel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsConnection straight with thread external BSP, NPTF and fitting for hose measurement, supplied in set with a clamping ferrule. occurs in three variants: with thread external BSP (60° cone), with thread external BSP (sealing flat) or with thread external NPTF (tapered). Material: steel with coating zinc-nickel. Working pressure: 400 bar and 630 bar - depending on size. Operating temperature: od -30°C up to +120°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsNipple with thread internal and thread external, for pressure gauge of standard connections pressure-gauge according to EN 837-1. allows assembly pressure gauge for socket o greater size. pressure gauge mounted for thread internal d1. connection to has character self-sealing – cone on bottom hole d1 presses in hole plug centring the connection pressure gauge. threads d1 and d2 are protected against unscrewing connections through applied special adhesive. intended for liquids and gases non-aggressive, for mounting pressure gauge, cocks and valves pressure-gauge and other accessories equipped in ten type the connection. Material: steel AISI 316Ti.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsBolt BANJO DIN 7643, size M8, M10 and 1/8" BSP. Material: steel carbon, galvanized. Material: steel with coating zinc-nickel. Working pressure: 200 bar. Operating temperature: od -30°C up to +120°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThermometer bimetallic with sensor rear made in accordance with the standard EN 13190 for measuring temperatures liquids, par and gases in equipment industrial, in particular district-heating. is characterized quick reaction on changes temperatures and ease reading thanks to legible divider. thermometer mounted for devices using screw-in cover with thread external, protecting A sensor and enabling replacement thermometer without disturbing process – thermometer is pressed in cover sensor. On impact the medium o measured temperature should be exposed minimum 50% length sensor. available also in made stainless - version SS (housing dust-tight - IP65). Material: steel galvanized (housing), glass (sight glass), brass (A sensor and A guard). Diameter nominal: 63 mm, 100 mm. degree protection housing: IP41. Class accuracy: 2. length sensor: 50 mm, 80 mm, 100 mm. strength cover: 160 bar. Connection cover: 1/2" BSP female. range measuring: od -30°C up to +400°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSleeve crimping Intended for crimping micro-hoses thermoplastic DN2 and DN4, used in hydraulic systems measurement and control. Material: steel with coating zinc-nickel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA handle measuring for switching at low pressure. has Connection for pressure gauge, quick coupling with a shut-off valve, air vent (for TA-M-101-21A - valve).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, very pliable and flexible, resistant to kinking hose intended for oil hydraulic, liquids based on water and other media. used in systems measurement, control, hydraulic systems brake in bicycles and micro-hydraulics (systems opening roofs automotive). Layer outer with resistant to abrasion polyurethane or with polyamide and micro-perforated, co allows use hose for media gas. hose has resistance to vacuum for 0.93 bar. temperature above 80°C can reduce service life hose. hose DN2 with polyamide (ZC-TEST8-5021PA) passed positively tests pulse 1 million cycles. Inner layer: polyester or polyamide. Reinforcement: single an aramid braid. Outer layer: black polyurethane or polyamide. Working pressure: from 412 bar to 500 bar, depending on the diameter and type hose. Operating temperature: od -40°C up to +100°C (for water and air up to +70°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsMiniature plug quick coupling measurement DN1.2, with a cap plastic or metal and thread external, production Swedish intended for measuring pressure static, dynamic and vacuum in systems hydraulic. plug equipped in valve ensuring Leak-free connection, disconnection and tightness, even at vacuum 90%. plugs measurement made with hardened steel, durable and maintenance-free. connections with thread external sealed using an O-ring recessed in surface front (type A) or an O-ring at surface face (type B). Material: steel galvanized. sealing: NBR. Working pressure: 600 bar (for plugs TA-M-120: 400 bar).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPlug measuring equipped in a cap PVC, intended for connecting with socket TEMA 100, additional connected with line thermoplastic. Material: steel galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPlug quick coupling measurement SNAP-CHECK production Swedish intended for measuring pressure in systems hydraulics power. socket quick coupling connected are line with pressure gauge, a plugs quick coupling with hardened steel are standard mounted on fixed in system hydraulic and equipped in valves shut-off. connection socket with a plug possible is under pressure up to 300 bar. pressure working for disconnected with socket plug is 600 bar, a minimal pressure bursting 2400 bar. pressure working for connected socket and plug is also 600 bar, whereas minimal pressure bursting to 1300 bar. precision made quick couplings, ensures tightness and reliability points measurement the system hydraulic. range connections for plugs measurement allows easy configuration connections. plugs quick couplings, supplied are standard in set with red caps with plastic. Working pressure: 600 bar. pressure switching: up to 300 bar. Material body: steel galvanized. sealing: NBR. Operating temperature: od -30°C up to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPlug with a shut-off valve quick coupling diagnostic, with thread internal NPT, used for measuring pressure in systems hydraulics power. made according to standards ISO 15171-1 and SAE J1502, interchangeable are of couplings other manufacturers. plugs quick coupling with hardened steel, standard mounted are on fixed in system hydraulic, a socket quick coupling remain connected line with pressure gauge. connection socket with a plug should take place only at non-operating system, at the absence pressure or very low pressure a few bar. pressure working for disconnected with socket plug is 400 bar a minimal pressure bursting 1600 bar. pressure working for connected socket and plug, is also 400 bar, whereas minimal pressure bursting to 1300 bar. socket and plug equipped are in valves ensuring Leak-free connection and disconnection and tightness. Ich flat surfaces limit for minimum residual leakage oil and inclusion air for the system (leakage ok. 0.1 ml at disconnection, inclusion air ok. 0.02 ml at connecting). Dla correct operation important is retention purity surface valves. Working pressure: 400 bar. pressure bursting: 1300 bar. Vacuum: for 0.9 bar. Flow rate oil hydraulic at Δp = 3 bar: 4.2. Material: steel galvanized. sealing: NBR. Operating temperature: od -40°C up to +120°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPlug with a shut-off valve quick coupling diagnostic, with thread external NPT, used for measuring pressure in systems hydraulics power. made according to standards ISO 15171-1 and SAE J1502, interchangeable are of couplings other manufacturers. plugs quick coupling with hardened steel, standard mounted are on fixed in system hydraulic, a socket quick coupling remain connected line with pressure gauge. connection socket with a plug should take place only at non-operating system, at the absence pressure or very low pressure a few bar. pressure working for disconnected with socket plug is 400 bar a minimal pressure bursting 1600 bar. pressure working for connected socket and plug, is also 400 bar, whereas minimal pressure bursting to 1300 bar. socket and plug equipped are in valves ensuring Leak-free connection and disconnection and tightness. Ich flat surfaces limit for minimum residual leakage oil and inclusion air for the system (leakage ok. 0.1 ml at disconnection, inclusion air ok. 0.02 ml at connecting). Dla correct operation important is retention purity surface valves. Working pressure: 400 bar. pressure bursting: 1300 bar. Vacuum: for 0.9 bar. Flow rate oil hydraulic at Δp = 3 bar: 4.2. Material: steel galvanized. sealing: NBR. Operating temperature: od -40°C up to +120°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, very pliable and flexible, resistant to kinking hose intended for oil hydraulic, liquids based on water and other media. used in systems measurement, control and hydraulic systems brake in bicycles. On special order Layer outer micro-perforated. Inner layer: polyester. Reinforcement: single an aramid braid. Outer layer: black polyurethane. Working pressure: 625 bar or 660 bar, depending on the diameter hose. Operating temperature: od -40°C up to +93°C (for water and air up to +65°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick-coupling plug cap PD, standard ISO 15171-1. Material: NBR.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPlug cap TEMA 100 protecting against contamination and damage. Material: PVC or steel carbon.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsBrass needle valve shut-off with connection under pressure gauge, used in systems hydraulic as element insulating pressure gauge od installation. valve secures pressure gauge against overload and stroke pressure during opening and allows its replacement. occurs in two versions: straight – in-line (FPE) and angled 90° (FPEA). has thread under knob, enabling assembly panel. Do valve should use adapter o index DC-FPE-FPEA, tightened for the connection with thread internal (ordered separately). Material: brass nickel-plated (body), steel carbon (needle), steel galvanized (connection - A nut), plastic (knob). sealing: NBR. Connection: 2 x 1/4" BSP female (pressure-gauge). Operating temperature: od -20°C up to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSet equipped in Miniature quick coupling measurement DN1.2 production Swedish intended for measuring pressure static, dynamic and vacuum in systems hydraulic. based on classic the structure quick coupling type „push to connect” with mechanism locking plug consisting with balls, spring and ferrule locking. socket and plug equipped are in valves ensuring Leak-free connection and disconnection and tightness, even at vacuum 90%. plugs measurement made with hardened steel, durable and maintenance-free. connections with thread external sealed using an O-ring recessed in surface front (type A) or an O-ring at surface face (type B). ensures to straight and fast configuring connections. other element set measurement molds pressure gauge (no in set) mounted in holders measurement, adapters and hoses measurement. valve venting in holder measurement allows on removal bubbles air with the system, co increases accuracy measuring pressure dynamic. set It can be used for measurements pressure on machines equipped we plugs measurement TEMA SYSTEM 100 (some machine working e.g. VOLVO, HIAB, SAMSUNG) or through assembly plugs in system during measuring. flexible Adapter TA-M-139 allows on use set for measuring on Widely usedch couplings with thread M16x2. Do measurements using set can use each appropriate type pressure gauge (no in set) with typical connection pressure-gauge with thread external 1/4” BSP. recommended version pressure gauge: pressure gauge 63 mm type FM-631 - Connection with bottom. sealing pressure gauge in the socket handle using washer on thread and an O-ring 10.8x2.2, or washer pressure-gauge inside socket. set supplied is in plastic case and contains the following element: 1. A handle measuring for switching at low pressure (Connection for pressure gauge 1/4” BSP, socket quick coupling, air vent). 2. plug measuring, 1/8" BSP male, type A, cap plastic. 3. hose measuring (DN2, 630 bar), L=2.5 m with a plug quick coupling TA-M-120 and socket TA-M-150. 4. Adapter, 1/4" BSP female / 1/8" BSP male, type A. 5. Adapter, 1/8" BSP female / 1/4" BSP male, type B. sealing: NBR rubber. Working pressure: up to 600 bar, for plugs TA-M-120 - 400 bar.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsBasic set measuring intended is for diagnostics installation hydraulic and pneumatic through measurement pressure static, dynamic and vacuum. set contains plastic case with prepared space on two pressure gauge 63 mm and hose DN2 (630 bar) with fitting: measurement M16x2 female and for pressure gauge female 1/4” BSP o length 2000 mm. set not contain pressure gauge, which should select and separately order. Material ends hose: steel with coating zinc nickel. Working pressure: up to 630 bar.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSet measuring intended is for diagnostics installation hydraulic and pneumatic through measurement pressure static, dynamic and vacuum. set contains plastic case with prepared space on two pressure gauge 63 mm, hose DN2 (630 bar) with two fitting measurement M16x2 female o length 2000 mm and coupling and adapters: 1. coupling measurement M16x2 with a cap metal, with male thread 1/4” BSP, type E - 2 pcs 2. coupling measurement M16x2 with a cap metal, with male thread M8x1, type F - 1 pcs 3. coupling measurement M16x2 with a cap metal, with male thread M10x1, type F - 1 pcs 4. Connection with female thread 1/4” BSP for pressure gauge, bulkhead, with male thread M16x2 - 2 pcs 5. Connection with female thread 1/4” BSP for pressure gauge, with female thread M16x2 - 1 pcs 6. Adapter reducing male 3/8” BSP / M10x1 female, type E - 1 pcs 7. Adapter reducing male 1/2” BSP / M10x1 female, type E - 1 pcs set not contain pressure gauge, which should select and separately order. Material fittings: steel with coating zinc nickel. sealing: NBR. Working pressure: up to 630 bar.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSet measuring intended for diagnostics systems hydraulics power through measurement pressure. set supplied is in plastic case in following configuration: 1. pressure gauge glycerine 63 mm, Connection bottom 1/4” BSP, 0 ÷ 100 bar, pressure gauge glycerine 63 mm, Connection bottom 1/4” BSP, 0 ÷ 250 bar, pressure gauge glycerine 63 mm, Connection bottom 1/4” BSP, 0 ÷ 400 bar. 2. coupling measurement M16x2 with a cap plastic, with male thread 1/4” BSP, type E, coupling measurement M16x2 with a cap plastic, with male thread 3/8” BSP, type E. 3. coupling measurement M16x2 with a cap plastic, with male thread 1/4” NPT, type C, coupling measurement M16x2 with a cap plastic, with male thread 3/8” NPT, type C. 4. coupling measurement M16x2 with a cap plastic, with male thread M10x1, type F, coupling measurement M16x2 with a cap plastic, with male thread 7/16”-20 UNF, type F, coupling measurement M16x2 with a cap plastic, with male thread 9/16”-18 UNF, type F. 5. coupling measurement M16x2 with a cap metal, with connection DIN 2353 with female thread M18x1.5, 12L. 6. cap metal M16x2. 7. Connection with female thread 1/4” BSP for pressure gauge, with female thread M16x2, Connection with female thread 1/2” BSP for pressure gauge, with female thread M16x2. 9. Connection with female thread 1/4” BSP for pressure gauge, bulkhead, with male thread M16x2. 10. hose DN2 (630 bar) with two fitting measurement M16x2 female L = 1 m, hose DN2 (630 bar) with two fitting measurement M16x2 female L = 2 m. Material fittings: steel galvanized. sealing: NBR.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSet measuring intended for diagnostics systems hydraulics power through measurement pressure. set supplied is in plastic case in following configuration: 1. pressure gauge glycerine 63 mm, Connection bottom 1/4” BSP, 0 ÷ 160 bar, pressure gauge glycerine 63 mm, Connection bottom 1/4” BSP, 0 ÷ 315 bar. 2. coupling measurement M16x2 with a cap plastic, with male thread 1/4” BSP, type E, coupling measurement M16x2 with a cap plastic, with male thread 3/8” BSP, type E. 3. coupling measurement M16x2 with a cap plastic, with male thread 1/4” NPT, type C. 4. coupling measurement M16x2 with a cap plastic, with male thread M10x1, type F. 6. cap metal M16x2. 7. Connection with female thread 1/4” BSP for pressure gauge, with female thread M16x2. 8. Connection angled 90° with female thread 1/4” BSP for pressure gauge, with male thread M16x2. 10. hose DN2 (630 bar) with two fitting measurement M16x2 female L = 1.5 m. Material fittings: steel galvanized. sealing: NBR.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCoupling BANJO straight DIN 7642 with fitting intended for micro-hoses, complete with a clamping ferrule. Material: steel with coating zinc-nickel. Working pressure: 200 bar. Operating temperature: od -30°C up to +120°C.
