Our products
Select options This product has multiple variants. The options may be chosen on the product page / DetailsSocket with a shut-off valve quick coupling diagnostic, with thread internal NPT, used for measuring pressure in systems hydraulics power. made according to standards ISO 15171-1 and SAE J1502, interchangeable of couplings other manufacturers. plugs quick coupling with hardened steel are standard mounted on fixed in system hydraulic, a socket quick coupling connected are line with pressure gauge. connection socket with a plug should take place only at non-operating system, at the absence pressure or very low pressure a few bar. socket and plug equipped are in valves ensuring Leak-free connection and disconnection and tightness. Ich flat surfaces limit for minimum residual leakage oil and inclusion air for the system (leakage ok. 0.1 ml at disconnection, inclusion air ok. 0.02 ml at connecting). Dla correct operation important is retention purity surface valves. Working pressure: 400 bar. pressure bursting: 1300 bar. Vacuum: for 0.9 bar. Flow rate oil hydraulic at Δp = 3 bar: 4.2. Material: steel galvanized. sealing: NBR. Operating temperature: od -40°C up to +120°C.- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA universal pressure gauge industrial 63 mm with connection lower FM 631, produced in accordance with the standard EN 837-1 in housing of steel stainless with filling glycerine. pressure gauge resistant is on shocks, vibration, moisture, o elevated resistance to sudden rises pressure, intended for straight measurements pressure liquids o low viscosity, vapours and gases, not operating corrosion on alloys copper and not crystallising. filling pressure gauge glycerine promotes reduction fluctuations indicator and reduction wear parts moving mechanism at pulsations pressure and vibration. also prevents condensation and formation atmosphere corrosion inside pressure gauge, which could damage parts internal. range measuring should select appropriate for pressure use, tak to pressure fixed or slowly changing not exceed 75% range; pressure pulsating not exceed 60% range and pulses pressure not exceeded maximum range. Diameter disc: 63 mm. Material: housing - steel AISI304, sight glass - plexiglas, Connection - brass, mechanism - brass and alloys copper, filling - glycerine. Class accuracy: 1.6. temperature ambient: od -40°C up to +65°C. temperature medium: maximum +60°C. Connection bottom: 1/4" BSP male (G 1/4 B, EN ISO 228-1, B means tolerance thread).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA universal pressure gauge industrial 63 mm with connection rear FM 632, produced in accordance with the standard EN 837-1 in housing of steel stainless with filling glycerine. pressure gauge resistant is on shocks, vibration, moisture, o elevated resistance to sudden rises pressure, intended for straight measurements pressure liquids o low viscosity, vapours and gases, not operating corrosion on alloys copper and not crystallising. filling pressure gauge glycerine promotes reduction fluctuations indicator and reduction wear parts moving mechanism at pulsations pressure and vibration. also prevents condensation and formation atmosphere corrosion inside pressure gauge, which could damage parts internal. range measuring should select appropriate for pressure use, tak to pressure fixed or slowly changing not exceed 75% range; pressure pulsating not exceed 60% range and pulses pressure not exceeded maximum range. Diameter disc: 63 mm. Material: housing - steel AISI 304, sight glass - plexiglas, Connection - brass, mechanism - brass and alloys copper, filling - glycerine. Class accuracy: 1.6. temperature ambient: od -40°C up to +65°C. temperature medium: maximum +60°C. Connection rear: 1/4" BSP male (G 1/4 B, EN ISO 228-1, B means tolerance thread).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA universal pressure gauge industrial 63 mm with connection rear for installation FM 633, produced in accordance with the standard EN 837-1 in housing of steel stainless with filling glycerine. pressure gauge resistant is on shocks, vibration, moisture, o elevated resistance to sudden rises pressure, intended for straight measurements pressure liquids o low viscosity, vapours and gases, not operating corrosion on alloys copper and not crystallising. filling pressure gauge glycerine promotes reduction fluctuations indicator and reduction wear parts moving mechanism at pulsations pressure and vibration. also prevents condensation and formation atmosphere corrosion inside pressure gauge, which could damage parts internal. range measuring should select appropriate for pressure use, tak to pressure fixed or slowly changing not exceed 75% range; pressure pulsating not exceed 60% range and pulses pressure not exceeded maximum range. Diameter disc: 63 mm. Material: housing - steel AISI 304, sight glass - plexiglas, Connection - brass, mechanism - brass and alloys copper, filling - glycerine. Class accuracy: 1.6. temperature ambient: od -40°C up to +65°C. temperature medium: maximum +60°C. Connection rear: 1/4" BSP male (G 1/4 B, EN ISO 228-1, B means tolerance thread).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCoupling with thread internal and thread external, for pressure gauge of standard connections pressure-gauge according to EN 837-1. allows assembly pressure gauge for socket o other size. intended for liquids and gases non-aggressive, for mounting pressure gauge, cocks and valves pressure-gauge and other accessories equipped in ten type the connection. Material: steel AISI 316Ti.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCoupling with thread internal and thread external, for pressure gauge of standard connections pressure-gauge according to EN 837-1. allows assembly pressure gauge for socket o other size. intended for liquids and gases non-aggressive, for mounting pressure gauge, cocks and valves pressure-gauge and other accessories equipped in ten type the connection. Material: brass.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA clamp for mounting panel for pressure gauge type FM 632 with rear connection.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSteel needle valve shut-off with connection under pressure gauge, used in systems hydraulic as element insulating pressure gauge od installation, securing against overload and stroke pressure during opening and enabling replacement. version straight (FT290) and version angled 90° (FT291). possibility mounting panel on the thread under knob. On special order available also in made of steel stainless AISI 316. Material: galvanised carbon steel (body), steel carbon (needle), polyamide 66 (knob). sealing: NBR/PTFE. Working pressure: 350 bar. Operating temperature: od -20°C up to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsNipple with thread internal and thread external, for pressure gauge of standard connections pressure-gauge according to EN 837-1. allows assembly pressure gauge for socket o greater size. pressure gauge mounted for thread internal d1. connection to has character self-sealing – cone on bottom hole d1 presses in hole plug centring the connection pressure gauge. threads d1 and d2 are protected against unscrewing connections through applied special adhesive. intended for liquids and gases non-aggressive, for mounting pressure gauge, cocks and valves pressure-gauge and other accessories equipped in ten type the connection. Material: brass.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA guard rubber pressure gauge o diameter disc 63 mm, fully role protection against impacts and destruction. Intended for pressure gauge with connection lower and rear.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSpecial Adapter for direct connection pressure gauge for the system hydraulic. limited Flow rate oil through small hole in adapter dampens sudden strokes pressure in system. rotational A nut allows appropriate setting pressure gauge. On special order Available also of steel stainless AISI 316. Material: steel galvanized. sealing: NBR. Operating temperature: od -20°C up to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsBrass needle valve shut-off with connection under pressure gauge, used in systems hydraulic as element insulating pressure gauge od installation. valve secures pressure gauge against overload and stroke pressure during opening and allows its replacement. occurs in two versions: straight – in-line (FPE) and angled 90° (FPEA). has thread under knob, enabling assembly panel. Material: brass nickel-plated (body), steel carbon (needle), steel galvanized (connection - A nut), plastic (knob). sealing: NBR. Connection: 1/4" BSP female (pressure-gauge), 1/4" BSPT male. Operating temperature: od -20°C up to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsAdapter consists ofcy additional equipment valves shut-off type FPE and FPEA. Working pressure: 350 bar. Material: steel carbon, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCoupling measurement designed is according to requirements standards ISO 15171-2. used primarily for diagnostics pressure in systems hydraulics power, can be also used for systems lubrication, venting, sampling samples oil and micro-hydraulics. intended for oil hydraulic and oils mineral, made of carbon steel with coated zinc-nickel, with seals with NBR, made of Viton (marked on the end index letter "V") and with EPDM marked on the end index letter "EA"). available in version with a cap metal or a cap plastic (plastic). coupling has standard for standards ISO 15171-2, thread M16x2 od side fittings measurement, and appropriate Connection for connection for installation hydraulic. Material: steel with coating zinc-nickel. Working pressure: from 400 bar to 630 bar - dependent od type. sealing: NBR, Viton, EPDM. Operating temperature: od -30°C up to +120°C - NBR (od -30°C up to +100°C with a cap with plastic), od -20°C up to +200°C - Viton.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-pressure adapter hydraulic, reduces thread internal metric or BSP (sealing on the thread) on thread external BSP (sealing type E - rubber gasket shaped). Material: steel with coating galvanised-nickel. sealing: NBR. Working pressure: from 400 bar to 630 bar - depending on size. Operating temperature: od -30°C up to +120°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsAdapter threaded intended for connecting with other element system measurement TEMA 100. Available in version straight and angled (90°). Material: brass nickel-plated.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSocket 90° quick coupling measurement SNAP-CHECK production Swedish intended for measuring pressure in systems hydraulics power. plugs quick coupling with hardened steel are standard mounted on fixed in system hydraulic, a socket quick coupling connected are line with pressure gauge. connection socket with a plug possible is under pressure up to 300 bar. pressure working for disconnected with socket plug is 600 bar, a minimal pressure bursting 2400 bar. pressure working for connected socket and plug is also 600 bar, whereas minimal pressure bursting to 1300 bar. precision made quick couplings, ensures tightness and reliability points measurement the system hydraulic. range connections for plugs measurement allows easy configuration connections. socket quick couplings, supplied are standard in set with red caps with plastic. Working pressure: 600 bar. pressure switching: up to 300 bar. Material body: steel galvanized. sealing: NBR. Operating temperature: od -30°C up to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSocket measurement intended for connecting with a plug TEMA 100. W version with thread external and internal (with an adapter). Material: steel galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSocket quick coupling measurement SNAP-CHECK production Swedish intended for measuring pressure in systems hydraulics power. plugs quick coupling with hardened steel are standard mounted on fixed in system hydraulic, a socket quick coupling connected are line with pressure gauge. connection socket with a plug possible is under pressure up to 300 bar. pressure working for disconnected with socket plug is 600 bar, a minimal pressure bursting 2400 bar. pressure working for connected socket and plug is also 600 bar, whereas minimal pressure bursting to 1300 bar. precision made quick couplings, ensures tightness and reliability points measurement the system hydraulic. range connections for plugs measurement allows easy configuration connections. socket quick couplings, supplied are standard in set with red caps with plastic. Working pressure: 600 bar. pressure switching: up to 300 bar. Material body: steel galvanized. sealing: NBR. Operating temperature: od -30°C up to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSocket with a shut-off valve quick coupling diagnostic, with thread external NPT, used for measuring pressure in systems hydraulics power. made according to standards ISO 15171-1 and SAE J1502, interchangeable of couplings other manufacturers. plugs quick coupling with hardened steel are standard mounted on fixed in system hydraulic, a socket quick coupling connected are line with pressure gauge. connection socket with a plug should take place only at non-operating system, at the absence pressure or very low pressure a few bar. socket and plug equipped are in valves ensuring Leak-free connection and disconnection and tightness. Ich flat surfaces limit for minimum residual leakage oil and inclusion air for the system (leakage ok. 0.1 ml at disconnection, inclusion air ok. 0.02 ml at connecting). Dla correct operation important is retention purity surface valves. Working pressure: 400 bar. pressure bursting: 1300 bar. Vacuum: for 0.9 bar. Flow rate oil hydraulic at Δp = 3 bar: 4.2. Material: steel galvanized. sealing: NBR. Operating temperature: od -40°C up to +120°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsO-ring anti-vibration 12.6 mm x 2.4 mm, for caps metal coupling measurement M16x2. Material: NBR. Hardness: 70 Sh. Operating temperature: od -30°C up to +120°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCalorimetric meter flow rate flow air or nitrogen in installation, optionally for other gases. occurs in two ranges pressures up to 16 bar and up to 40 bar. principle measuring calorimetric consists in on cooling heated electrically sensor through flowing air. cooling sensor is directly dependent od flow mass air, hence not requires compensation pressure and temperatures. meter digital measures momentary flow flow and counts using pulses total wear compressed air. is to displayed on display, a all measurements can be transmitted through coupling to the standard Modbus RTU. Flowmeter can be quickly and easily removed without removing entire section measurement with installation in order to cleaning or calibration. cap for flowmeter ensures continuous use with lines in time cleaning. line bypass section measurement not is required. Flowmeter EW 850 thanks to its compact construction It can be used for measuring flow and wear air we all places installation od compressor until for smallest equipment and tools. range measuring should be selected appropriate for flow in installation. Due to possibility occurrence errors measurement necessary is avoiding condensation on element sensor or moisture conveyed medium. Not should exceed ranges use flowmeter! at selecting flowmeter for other gases than air or nitrogen please o contact with Tubes International. Working pressure: up to 16 bar or up to 40 bar. Material: steel stainless AISI 304 (section measurement, for version 16 bar), steel stainless AISI 316 (section measurement, for version 40 bar), polycarbonate (housing). medium: air, nitrogen (option - other gases). unit flow: m³/h, l/min. accuracy: ± 1.5% value measurement, ± 0.3% full scale. outlet analogue: 4 ÷ 20 has,
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLine thermoplastic terminated a plug TEMA 100 with a plug TA-M-120 and socket TA-M-150 TEMA 100. length line: 2.5 m. Operating temperature: od -40°C up to +93°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsConnection for pressure gauge 90° with thread internal inch BSP, adjustable and standard for standards ISO 15171-2, thread external M16x2, od side fittings measurement. coupling occurs in two variants: of free flow and with silencer strokes pressure. Material: steel with coating zinc-nickel. Working pressure: 630 bar. sealing: NBR. Operating temperature: od -30°C up to +120°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsConnection for pressure gauge with thread internal inch BSP or NPTF, bulkhead and standard for standards ISO 15171-2, thread external M16x2, od side fittings measurement. coupling occurs in two variants: of free flow and with silencer strokes pressure. Material: steel with coating zinc-nickel. Working pressure: 630 bar. sealing: NBR. Operating temperature: od -30°C up to +120°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsConnection for pressure gauge with thread internal and fitting Intended for micro-hoses, complete with a clamping ferrule. Connection occurs in two variants: with a nut swivel (with thread metric and BSPT, sealing O-ring NBR) and a nut constant (with thread NPTF and BSPT). Material: steel with coating zinc-nickel. Working pressure: 500 bar or 630 bar - depending on size hose. Operating temperature: od -30°C up to +120°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsConnection for pressure gauge with thread internal inch BSP or NPTF and standard for standards ISO 15171-2 thread internal M16x2, od side fittings measurement. coupling occurs in two variants: of free flow and with silencer strokes pressure. Material: steel with coating zinc-nickel. Working pressure: 630 bar. sealing: NBR. Operating temperature: od -30°C up to +120°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsConnection metric ISO 12151-2 24° cone with an O-ring and a nut, angled 90° and fitting for hose measurement. Connection occurs as: L (series light) and S (series heavy), A fitting whereas Intended is for hoses DN2 or DN4 and supplied in set with a clamping ferrule. Material: steel with coating zinc-nickel. Working pressure: from 250 bar to 630 bar - depending on size. sealing: O-ring NBR. Operating temperature: od -30°C up to +120°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsConnection metric ISO 12151-2 24° cone with an O-ring and a nut, straight and fitting for hose measurement. connection occurs as: L (series light) and S (series heavy), A fitting whereas Intended is for hoses DN2 or DN4 and supplied in set with a clamping ferrule. Material: steel with coating zinc-nickel. Working pressure: from 250 bar to 630 bar - depending on size. sealing: O-ring NBR. Operating temperature: od -30°C up to +120°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsConnection measurement with thread internal 5/8" BSF (standard typical for machine JCB) and fitting Intended for micro-hoses o diameter 2x5 mm. W set also plug with thread external with a cable steel. Material: steel carbon, galvanized. Working pressure: 420 bar. sealing: NBR. Operating temperature: od -30°C up to +120°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsConnection measurement 5/8" BSF, type British HSP, standard JCB with a cap metal and with thread external BSP, for connection for installation hydraulic. connection equipped is in ball valve. Material: steel carbon, galvanized. sealing: NBR. Working pressure: 420 bar. Operating temperature: od -30°C up to +120°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsConnection measurement M16x2 with a cap metal. coupling has standard for standards ISO 15171-2, thread M16x2 od side fittings measurement, and appropriate Connection for connection for installation hydraulic with thread external JIC (7/16"-20 UNF, 37° cone) or metric (M16x2). Material: steel with coating zinc-nickel. Working pressure: from 450 bar to 630 bar - dependent od type. sealing: NBR. Operating temperature: od -30°C up to +120°C (od -30°C up to +100°C with a cap with plastic).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsConnection measurement M16x1.5 (standard military) with a cap metal and with thread external BSP for connection for installation hydraulic. Material: steel with coating zinc-nickel. sealing: NBR. Working pressure: 630 bar. Operating temperature: od -30°C up to +120°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsConnection measurement M16x2 with a cap metal or plastic (plastic). coupling has standard for standards ISO 15171-2, thread M16x2 od side fittings measurement, and appropriate Connection for connection for installation hydraulic acc. to DIN 2353, 24° cone, series heavy S. Material: steel with coating zinc-nickel. Working pressure: 630 bar. sealing: NBR. Operating temperature: od -30°C up to +120°C (od -30°C up to +100°C with a cap with plastic).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsConnection measurement M16x2 with a cap metal or plastic (plastic). coupling has standard for standards ISO 15171-2, thread M16x2 od side fittings measurement, and appropriate the connection for connection for installation hydraulic with thread external and internal BSP (60° cone). Material: steel with coating zinc-nickel. Working pressure: from 345 bar to 400 bar - depending on size. sealing: NBR. Operating temperature: od -30°C up to +120°C (od -30°C up to +100°C with a cap with plastic).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsConnection measurement M16x2 with a cap metal or plastic. coupling has standard for standards ISO 15171-2, thread M16x2 od side fittings measurement, and appropriate Connection for connection for installation hydraulic with thread internal JIC (UNF, 37° cone) or BSP (60° cone). Material: steel with coating zinc-nickel. Working pressure: from 450 bar to 630 bar - dependent od type. sealing: NBR. Operating temperature: od -30°C up to +120°C
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCoupling measurement designed is according to requirements standards ISO 15171-2. used primarily for diagnostics pressure in systems hydraulics power, can be also used for systems lubrication, venting, sampling samples oil and micro-hydraulics. intended for oil hydraulic and oils mineral, made of carbon steel with coated zinc-nickel, with seals with NBR. available in version with a cap metal or a cap plastic (plastic). coupling has standard for standards ISO 15171-2, thread M16x2 od side fittings measurement, and appropriate Connection for connection for installation hydraulic acc. to DIN 2353, 24° cone, O-ring. occurs as: L (series light) and S (series heavy), with a nut wire type A or a nut interleaved type B. Material: steel with coating zinc-nickel. Working pressure: from 100 bar to 630 bar - dependent od type. sealing: NBR. Operating temperature: od -30°C up to +120°C (od -30°C up to +100°C with a cap with plastic).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCoupling measurement designed is according to requirements standards ISO 15171-2. used primarily for diagnostics pressure in systems hydraulics power, can be also used for systems lubrication, venting, sampling samples oil and micro-hydraulics. intended for oil hydraulic and oils mineral, made of carbon steel with coated zinc-nickel, with seals with NBR. available in version with a cap metal or a cap plastic (plastic). coupling has standard for standards ISO 15171-2, thread M16x2 od side fittings measurement, and appropriate the connection for connection for installation hydraulic acc. to DIN 2353 for pipes, 24° cone, a nut and rings cutting. occurs as: L (series light) and S (series heavy). Material: steel with coating zinc-nickel. Working pressure: from 100 bar to 630 bar - dependent od type. sealing: NBR. Operating temperature: od -30°C up to +120°C (od -30°C up to +100°C with a cap with plastic).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsConnection measurement with thread internal M16x2 (ISO 1517-2), M16x1.5 or S12.65x1.5 and fitting for hose measurement, supplied in set with a clamping ferrule. Material: steel with coating zinc-nickel or steel AISI 316. Working pressure: 500 bar or 630 bar - depending on size. Operating temperature: od -30°C up to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsConnection straight with thread internal metric, BSP, JIC or ORFS, with a nut swivel and fitting for hose measurement, supplied in set with a clamping ferrule. Material: steel with coating zinc-nickel or steel AISI 316. Working pressure: from 400 bar to 630 bar - depending on size. Operating temperature: od -30°C up to +120°C.
