0

Our products

    Filters
      Product categories
      Working pressure [bar]
      Minimum operating temperature [°C]

      Minimum operating temperature [°C]: -55 — 0

      Maximum operating temperature [°C]

      Maximum operating temperature [°C]: 50 — 150

      Material
      Vacuum resistance
      Standard length [m]
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Module branching two-way GA series G with thread internal BSP, serves for draw air with any space stations FRL. Supply pressure: up to 10 bar. Operating temperature: up to +70°C.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Module branching PA, series SKILLAIR®, with plates end, serves for draw air with stations FRL in any phase its preparation, independently od space mounting. Size: 100, 200, 300. Supply pressure: up to 15 bar (13 bar - size 200, 300). Operating temperature: up to +50°C. Connection: 1/4" BSP female ÷ 1".
        • Select options This product has multiple variants. The options may be chosen on the product page / Details

          Module branching, series NEW DEAL

          Air preparation elements (FRL) | All products
          0 €
          Module branching used is in case when occurs need draw air with unit FRL Newdeal in any phase its preparation, e.g. air reduced, non-oiled czy supply. Size: 1/4", 3/8", 1/2", 3/4", 1". Connection: 1/8" BSP female for 1/4", 1/4" BSP female for 3/8" ÷ 1/2", 1/2" BSP female for 3/4" ÷ 1". Working pressure: up to 18 bar. Operating temperature: od -10°C up to +50°C.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details

          Module branching, series SYNTESI® version 2-way

          Air preparation elements (FRL) | All products
          0 €
          Module branching - connector mounted between two any modules SYNTESI®, serving for independent draw air. version 2-way, has two the connection (top and bottom). Size: SY1, SY2. pressure working and temperature: dependent od modules SYNTESI®, with which is connected. Flow rate: 1550 l/min - 1/8" (SY1), 7000 l/min - 3/8" (SY2), (at an inlet pressure of 6 bar Δp = 1 bar).
        • Select options This product has multiple variants. The options may be chosen on the product page / Details

          Module branching, series SYNTESI® version 4-way

          Air preparation elements (FRL) | All products
          0 €
          Module branching is to connector mounted between two any modules SYNTESI®, serving for independent draw air. has 4 socket for connections end on each plane. Size: SY1, SY2. Working pressure: up to 15 bar for SY1 and up to 13 bar for SY2. Operating temperature: od -10°C up to +50°C. Flow rate: 500 - 2000 l/min - SY1, 1500 - 4500 l/min - SY2, (at an inlet pressure of 6 bar Δp = 1 bar).
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Tool facilitating disconnection pipes in system SPEEDFIT. Material: plastic plastic.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details

          A nozzle protective SPEEDFIT, plastic plastic

          All products | Pneumatic piping systems
          0 €
          A nozzle protective for fittings SPEEDFIT protecting coupling against unintended disconnection, used in installations compressed air. Material: plastic plastic.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details

          Cutter for pipes aluminum, plastic plastic

          All products | Pneumatic piping systems
          0 €
          Cutter for pipes aluminum o diameter 4 ÷ 30 mm, for use in system SPEEDFIT. Material: plastic plastic.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Connection with spigot with thread external BSP or metric for connecting hoses with plastics (for hoses polyurethane required minimum Hardness per Shore (A): 98°). Material: brass nickel-plated. Operating temperature: od -15°C up to +130°C. Working pressure: 30 bar. sealing: Viton.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details

          Regulator compressed air panel, type 367

          Air preparation elements (FRL) | All products
          0 €
          A diaphragm-type reducing valve with a pressure gauge built into the knob, ideal for panel mounting. It has an air bleed to the atmosphere. High accuracy in maintaining the output pressure. Panel mounting element are available (EW-367K33). Material: alloy zinc and aluminum. Size: 3/8”. Supply pressure: up to 25 bar. Operating temperature: od -10°C up to +90°C. Connection: 3/8" BSP female. Flow rate 1000 l/min (at an inlet pressure of 8 bar and Dp = 1 bar).
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Actuator double-acting operation with magnet and cushioning ISO 15552 series 3. has special sleeve o reduced for minimum weight, made with aluminum anodized, calibrated, and two grooves for mounting sensors on common plane with ports supply. other wall are smooth and easy in cleaning. cover actuator made with high-pressure casting aluminum. Piston diameter: Ø 32 ÷ 100 mm. stroke working: od 50 for 800 mm. Working pressure: od 0.4 up to 10 bar. sealing: NBR, polyurethane. Operating temperature: od -10°C up to +80°C.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Actuator A compact series CMPC, with piston rod with thread internal, features small weight and short installation, co allows ich assembly in hard reachable places. special profile actuator connected is with covers external using bolts, a to ensures optimal its rigidity axial and increases variety ways its mounting. depending on version equipped is or not in magnet built-in in piston, a grooves in profile enable use sensors magnetic without additional accessories. made in accordance with the standard ISO 15552. standard ta allows on easy and fast selection and replacement actuator during work repair machine. Piston diameter: Ø 32 ÷ Ø 100. type actuator: double-acting operation, double-acting operation with passing piston rod and single-acting operation of hidden piston rod. Material piston rod: steel C45 chrome-plated or steel stainless. maximum Working pressure: up to 10 bar. Operating temperature: od -10°C up to +80°C.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Actuator single-acting operation ISO 15552 type A, has cover made with high-pressure casting aluminum and profile made with aluminum anodized, calibrated, which contains on three walls longitudinal grooves enabling direct assembly and protection sensors position piston. Te same grooves serve for direct mounting valves and other mechanical parts. Piston diameter: Ø 32 ÷ 63 mm. stroke working: od 30 for 200 mm. Working pressure: od 0.4 up to 10 bar. sealing: polyurethane. Operating temperature: od -10°C up to +80°C.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Actuator short-stroke double-acting operation, with protection against rotation with magnet. series SSCY is characterized compact design and Intended is for mounting in confined spaces. service life working actuators without loads transverse with seals with NBR is 15 million cycles, with seals polyurethane 30 million cycles. Z notes on variability many agents having influence on service life, The presented value not should be treated as binding or guaranteed, a only as reference. available diameter piston: Ø 12 ÷ 80 mm. stroke working: od 10 for 80 mm. Material seal actuator: NBR, polyurethane. Working pressure: od 0.4 up to 10 bar - depending on the diameter piston. Operating temperature: od -10°C up to +80°C - depending on kinds seal.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Actuator A compact series CMPC, with piston rod with thread external, features small weight and short installation, co allows ich assembly in hard reachable places. special profile actuator connected is with covers external using bolts, a to ensures optimal its rigidity axial and increases variety ways its mounting. depending on version equipped is or not in magnet built-in in piston, a grooves in profile enable use sensors magnetic without additional accessories. made in accordance with the standard NFE 49-004-1 and 2 (UNITOP). standard ta allows on easy and fast selection and replacement actuator during work repair machine. selected actuator have through-flow hole in piston rod. Piston diameter: Ø 32 ÷ Ø 100. type actuator: single-acting and double-acting operation. Material piston rod: steel C45 chrome-plated or steel stainless. minimal Working pressure: 0.4 ÷ 0.6 bar, depending on the diameter. maximum Working pressure: up to 10 bar. Operating temperature: od -10°C up to +80°C.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details

          Actuator with double piston rod series TWNC

          All products | Pneumatic actuators
          0 €
          Actuator double-acting operation with passing double piston rod It can be used as element actuating in systems, in which required is protection against rotation. W the scope dimensions axial compliant with the standard ISO 15552. standard configuration with magnet and cushioning. Piston diameter: Ø 32, 40, 50, 63, 80, 100 mm. Maximum, recommended length stroke: od 25 for 500 mm. Working pressure: up to 10 bar. sealing: polyurethane. medium working: filtered compressed air, oiled or non-oiled. force produced at 6 bar extension/return: Ø 32 - 434/350 N, Ø 40 - 678/597 N, Ø 50 - 1060/940 N, Ø 63 - 1683/1471 N, Ø 80 - 2714/2295 N, Ø 100 - 4241/3812 N. Operating temperature: od -10°C up to +80°C.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details

          Grease nipple compressed air LUB, series SYNTESI®

          Air preparation elements (FRL) | All products
          0 €
          Grease nipple pneumatic to straight and most widely used solution, ensuring correct lubrication mist oil, devices actuating in installations pneumatic. process suction oil takes place due to a drop pressure generated in venturi Venturi. amount drops oil introduced for stream air is dosed through needle adjustment. On rear and front surface lubricator is found the connection auxiliary for connection pressure gauge, sensor pressure or for additional draw air. Size: SY1, SY2. capacity bowl: 60 cm³ - SY1, 130 cm³ - SY2. Supply pressure: up to 15 bar for SY1 and up to 13 bar for SY2. Operating temperature: od -10°C up to +50°C. Connection: 1/8" BSP female ÷ 3/8" for SY1 and 3/8" BSP female ÷ 1" for SY2. Flow rate: 1600 l/min - 1/8", 3000 l/min - 1/4", 3650 l/min - 3/8", 6100 l/min - 1/2", 3/4", 1" (at an inlet pressure of 6 bar Δp = 1 bar).
        • Select options This product has multiple variants. The options may be chosen on the product page / Details

          Grease nipple compressed air, size DN6

          Air preparation elements (FRL) | All products
          0 €
          Grease nipple compressed air with polycarbonate tank, ensures correctness lubrication mist oil equipment in installations pneumatic. Size: DN6. assembly: vertical. Material housing: brass. sealing: NBR. capacity bowl: 40 cm 3. Supply pressure: up to 16 bar. Operating temperature: od -10°C up to +50°C. Connection: 1/4" BSP female. Flow rate: 1160 l/min (at an inlet pressure of 6 bar Δp = 1 bar). weight: 400 g.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Bolt BANJO with an O-ring and thread internal type D9 for coupling type R28, R29. Material: brass nickel-plated. Working pressure: 18 bar.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details

          Bolt for mounting wall, system SYNTESI

          Accessories for FRL | All products
          0 €
          Bolt for mounting wall for system SYNTESI (1 pcsa). Material: steel carbon, galvanized.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Bolt double BANJO with an O-ring type D8 for coupling type R28, R29. Material: brass nickel-plated. Working pressure: 18 bar.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details

          Screws assembly, system NEW DEAL CVA

          Accessories for FRL | All products
          0 €
          Screws assembly for system NEW DEAL CVA (2 pcsi). Material: steel carbon, galvanized.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details

          Screws tie, system NEW DEAL F+L

          Accessories for FRL | All products
          0 €
          Screws tie (assembly) intended for system NEW DEAL F+L (2 pcsi). Material: steel galvanized.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Tee "L" of steel stainless type 62450, 1x thread external BSPT and 2x thread internal BSP. Material: steel AISI 316L. Operating temperature: od -20°C up to +225°C. Working pressure: 140 bar.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Tee "T" of steel stainless type 62440, 1x thread external BSPT and 2x thread internal BSP. Material: steel AISI 316L. Operating temperature: od -20°C up to +225°C. Working pressure: 140 bar.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Coupling push-in "T" adjustable with thread external BSP for connecting hoses with plastics (for hoses polyurethane required minimum Hardness per Shore (A): 98°). Material: brass nickel-plated. Operating temperature: od -15°C up to +130°C. Working pressure: 30 bar. sealing: Viton.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Elbow screw with thread external tapered BSPT, series F type R 39 NSF. intended for industry food (e.g. for cold or hot water potable). no element plastic, coated coating nickel in special process chemical and seal made of Viton ensure high resistance to action detergents and other agents chemical. is suitable also for many applications in industry chemical, pharmaceutical, electronic and in medicine. Operating temperature: od -20°C up to +150°C. Working pressure: 16 bar. Vacuum: 0.99 bar. Material: brass nickel-plated. sealing: Viton (approved for contact with food through FDA). standards: NSF/ANSI 51, NSF/ANSI 61.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Tee angled, swivel, screw-in with thread external cylindrical, series F type R 38 NSF. intended for industry food (e.g. for cold or hot water potable). no element plastic, coated coating nickel in special process chemical and seal made of Viton ensure high resistance to action detergents and other agents chemical. is suitable also for many applications in industry chemical, pharmaceutical, electronic and in medicine. Operating temperature: od -20°C up to +150°C. Working pressure: 16 bar. Vacuum: 0.99 bar. Material: brass nickel-plated. sealing: Viton (approved for contact with food through FDA). standards: NSF/ANSI 51, NSF/ANSI 61.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Tee plug-in "T" adjustable with thread external, type R32C, intended for connections lines and other element in systems pneumatic. easy and fast in use for repeated mounting without loss tightness po side mechanical and pneumatic. Material: brass nickel-plated. Working pressure: 16 bar. medium working: vacuum, air. Operating temperature: od -20°C up to +80°C. sealing: NBR.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Tee plug-in "T" double with thread external, type R51, intended for connections lines and other element in systems pneumatic. easy and fast in use for repeated mounting without loss tightness po side mechanical and pneumatic. Material: brass nickel-plated. Working pressure: 16 bar. medium working: vacuum, air. Operating temperature: od -20°C up to +80°C. sealing: NBR.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          High quality Connection Tee "T" with thread external parallel (BSP or M5), made entirely of steel AISI 316L, series 60215. no element plastic, and seal made of Viton ensure high resistance to action agents corrosion and substances chemical. used in industry chemical, food, pharmaceutical, electronic and in medicine. Material: steel AISI 316L. Operating temperature: od -15°C up to +225°C. Working pressure: 15 bar. Vacuum: 0.99 bar. sealing: Viton.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Tee plug-in triple with thread external, type R53, intended for connections lines and other element in systems pneumatic. easy and fast in use for repeated mounting without loss tightness po side mechanical and pneumatic. Material: brass nickel-plated. Working pressure: 16 bar. medium working: vacuum, air. Operating temperature: od -20°C up to +80°C. sealing: NBR.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Tee with a water separator for system SPEEDFIT used in installations compressed air, for diameter outer tubes 22 mm. Material: plastic plastic. Working pressure: 10 bar (+23°C), 7 bar (+70°C). Operating temperature: od -20°C up to +70°C.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details

          Multiple Swivel coupling, brass

          Accessories for pneumatic fittings | All products
          0 €
          Multiple Swivel coupling on inlet thread internal BSP, at the outlet threads internal BSP. Working pressure: 12 bar. Operating temperature: od -10°C up to +80°C. Material: brass nickel-plated.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details

          Water separator for tee SPEEDFIT, brass

          All products | Pneumatic piping systems
          0 €
          Water separator for tee for pipes o diameter 28 mm for system SPEEDFIT. Material: brass. Working pressure: 10 bar (+23°C), 7 bar (+70°C). Operating temperature: od -20°C up to +70°C.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details

          Indicator pressure LAM L (thread – line)

          All products | Functional fittings
          0 €
          Indicator pressure LAM L in version with connection threaded with an O-ring on one side and coupling push-in on the other side (thread - line) serves for signalling (signal color green or orange) aeration the system; when configuration is vented to a sight glass signalling is "empty". Working pressure: 2 ÷ 10 bar. Operating temperature: od -20°C up to +60°C. medium: filtered compressed air, oiled or not oiled.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          A bracket model BC for mini actuator ISO 6432. W set with 1 pin and 2 rings securing. size actuator: Ø8, Ø10, Ø12, Ø16, Ø20, Ø25. Material: steel carbon, galvanized.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          A bracket model BC for actuator cylindrical series RNDC. supplied together with with 2 screws. size actuator: Ø32, Ø40, Ø50. Material: steel carbon, galvanized.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details

          A bracket fixing for a wall SFB, system BIT

          Accessories for FRL | All products
          0 €
          A bracket fixing for a wall (steam), intended for system BIT 1/8" and 1/4".
        • Select options This product has multiple variants. The options may be chosen on the product page / Details

          A connector electrical 15 mm

          All products | Equipment for pneumatic valves
          0 €
          A connector electrical 15 mm. color: black or transparent.
        Go to Top