0

Our products

    Filters
      Product categories
      Working pressure [bar]
      Minimum operating temperature [°C]

      Minimum operating temperature [°C]: -55 — 0

      Maximum operating temperature [°C]

      Maximum operating temperature [°C]: 50 — 150

      Material
      Vacuum resistance
      Standard length [m]
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Valve electric SOV L should for family LINE ON LINE®, terminated coupling series Fox (line – line) and can be joined with other products in series or parallel. despite small sizes, valves SOV L controlled are electrically indirectly through co have very high parameters working. embedded on pin special seal polyurethane ensure long service life valve. air drain can be silenced through built-in silencer. each valve has monostable Control hand and indicator activation – diode LED. Working pressure: 2.5 ÷ 7 bar. Voltage DC: 24V. Operating temperature: od -20°C up to +60°C. medium: filtered compressed air, oiled or not oiled. Flow rate nominal: 380 l/min - Ø6, 700 l/min - Ø8 (at an inlet pressure of 6 bar Δp = 1 bar).
        • Select options This product has multiple variants. The options may be chosen on the product page / Details

          A coil 30 mm Ø8 for valves CNOMO 060580

          All products | Equipment for pneumatic valves
          0 €
          A coil 30 mm Ø8 for solenoid valves CNOMO 060580. Insulation class: F155. Voltage tolerance: -10% for +10%. Protection degree: IP65 EN60529 with a connector. shape connector: DIN 43650 shape A. time use continuous: 100% ED.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Actuator A compact series CMPC, with piston rod with thread external, features small weight and short installation, co allows ich assembly in hard reachable places. special profile actuator connected is with covers external using bolts, a to ensures optimal its rigidity axial and increases variety ways its mounting. W equipped is in magnet built-in in piston, a grooves in profile enable use sensors magnetic without additional accessories. made in accordance with the standard ISO 15552. standard ta allows on easy and fast selection and replacement actuator during work repair machine. Piston diameter: Ø 32 ÷ Ø 100. type actuator: double-acting operation, double-acting operation with passing piston rod and single-acting operation. Material piston rod: steel C45 chrome-plated or steel stainless. minimal Working pressure: 0.4 ÷ 0.6 bar, depending on the diameter. maximum Working pressure: up to 10 bar. Operating temperature: od -10°C up to +80°C.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Coupling Tee "T" reducing of couplings push-in under hose o diameter metric, series S, type PUTM. economical solution for connecting flexible hoses pneumatic o metric calibrated diameter outer. easy and fast in use. Material: plastic plastic. Working pressure: 10 bar. Vacuum: 0.99 bar. Operating temperature: od 0°C up to +60°C.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Cap with thread internal BSP type A8 Intended for element pneumatics. Material: brass nickel-plated. Working pressure: 60 bar.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details

          Cap tubes SPEEDFIT, plastic plastic

          All products | Pneumatic piping systems
          0 €
          Cap tubes for system SPEEDFIT used in installations compressed air. Material: plastic plastic. Working pressure: 10 bar (+23°C), 7 bar (+70°C). Operating temperature: od -20°C up to +70°C.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Valve throttle check RFL L type U (coupling push-in on inlet and Connection threaded with an O-ring at the outlet, for valve) regulates stream flowing air in one direction. Working pressure: 10 bar. Operating temperature: od -20°C for +60° C. medium: filtered compressed air, oiled or not oiled.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details

          A sensor proximity SQ type square

          All products | Pneumatic actuators
          0 €
          A sensor proximity SQ type square for actuators is characterized a certain and quick a bracket using screws eccentric, the possibility mounting using a screwdriver and wrench Allen 2.5 mm, edges thrust locating A sensor during mounting, increased resistance to factors atmospheric and moisture (IP 67, IP 68, IP 69K). Material housing sensor: polyamide (PA). Voltage supply: 5 ÷ 30V AC/DC (10 ÷ 30V AC/DC - HALL). Operating temperature: od -30°C up to +80°C (od -5°C up to +80°C - installations dynamic).
        • Select options This product has multiple variants. The options may be chosen on the product page / Details

          Button flat monostable VRM-010 RN

          All products | Equipment for pneumatic valves
          0 €
          Button flat monostable VRM-010 RN for valve VME. Do mounting required is Adapter VME1-000.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Tee "T" 2x female threadint internal BSP, 1xgwint external BSPT type A12, intended for connecting element pneumatics (in this hoses) of each other. tightness connections requires with rules use additional seals. W case thread tapered tape PTFE or sealant, in case thread parallel washers aluminum or copper. Material: brass nickel-plated. Working pressure: 60 bar.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Tee plug-in "T" adjustable with thread external, type R32, intended for connections lines and other element in systems pneumatic. easy and fast in use for repeated mounting without loss tightness po side mechanical and pneumatic. Material: brass nickel-plated. Working pressure: 16 bar. medium working: vacuum, air. Operating temperature: od -20°C up to +80°C. sealing: NBR.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Multi-hose in outer cover with black polyurethane, intended for installation pneumatic, hydraulic, oil, fuel, lubrication and chemicals. various color hoses enable easy identification individual circuits supply or various media. amount hoses: 2. Hose material: polyamide PA 12 (nylon). Working pressure: from 7.5 bar to 33 bar (in dependence od diameter and wall thickness wall hose). Operating temperature: od -20°C up to +80°C (for liquids containing water up to +65°C).
        • Select options This product has multiple variants. The options may be chosen on the product page / Details

          Cap fitting SPEEDFIT, plastic plastic

          All products | Pneumatic piping systems
          0 €
          Cap fitting for system SPEEDFIT used in installations compressed air. Material: plastic plastic. Working pressure: 10 bar (+23°C), 7 bar (+70°C). Operating temperature: od -20°C up to +70°C.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          A universal valve directional o control electric (solenoid valve), without a coil control, used most often for control operation actuators. can be mounted in lines, for a wall, directly for actuators or on block connection. Function 5/2 - five-way, two-position. Material: body valve - aluminum, spool - aluminum nickel-plated, sealing - NBR, Cover end - plastic plastic. Working pressure: up to 10 bar. Operating temperature: -10°C up to +60°C.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details

          Block connection, type A21

          All products | Threaded pneumatic fittings
          0 €
          Block the directional valve type A21 with threads internal (A cross). has coupling threaded intended for connecting element pneumatics. Material the directional valve: technopolymer. Material Connections: brass. Working pressure: 13 bar. Operating temperature: +50°C.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details

          Head fork for actuator pneumatic model GK-M

          All products | Pneumatic actuators
          0 €
          Head fork for mounting on piston rod actuator. Do use in case occurrence loads not being in axis piston rod actuator. head fork gives greater the ability assembly. thread: M4 ÷ M36x2. Material: galvanised carbon steel.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details

          A blade for shears JG-TS32

          All products | Pneumatic piping systems
          0 €
          A blade spare for shears JG-TS32.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details

          Button poppet monostable VRM-050 R

          All products | Equipment for pneumatic valves
          0 €
          Button poppet monostable VRM-050 R for valve VME. color: red.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Coupling Tee "Y" of couplings push-in under hose o diameter metric, series S, type PYM. economical solution for connecting flexible hoses pneumatic o metric calibrated diameter outer. easy and fast in use. Material: plastic plastic. Working pressure: 10 bar. Vacuum: 0.99 bar. Operating temperature: od 0°C up to +60°C.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          A universal valve directional o control manual, a plunger of assist, for control panel. used most often for control operation actuators. during mounting required is always Adapter MW-035100005. Function 3/2 - three-way, two-position. Size: 1/8". Material: body valve - aluminum, spool - aluminum nickel-plated, sealing - NBR, Cover end - plastic plastic. Working pressure: up to 10 bar. Operating temperature: -10°C up to +60°C.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details

          A coil 22 mm UL and CSA for valves PIV.I, stem Ø8

          All products | Equipment for pneumatic valves
          0 €
          A coil 22 mm UL and CSA for valves PIV.I, stem Ø8. Insulation class: F155. Voltage tolerance: -10% for +15%. Protection degree: IP65 EN60529 with a connector.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          A cross with threads internal BSP type A14 intended for connecting element pneumatics (in this hoses) of each other. tightness connections requires with rules use additional seals. W case thread tapered tape PTFE or sealant, in case thread parallel washers aluminum or copper. Material: brass nickel-plated. Working pressure: 60 bar.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          A bracket ISO for mounting with a flange swivel. W set: 4 screws with washers. Material: aluminum cast (flange), steel carbon galvanized (screws and washer).
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Valve throttle check type MRF NMC series COMPACT "N" for direct mounting in connections actuator, used in systems pneumatic for regulation level flowing stream compressed air and direction flow. equipped in coupling push-in ensuring easy disassembly lines pneumatic. change setting using a knob adjustment and/or a screwdriver; possibility securing setting a lock nut. Size: M5, 1/8″, 1/4″, 3/8″, 1/2″. Working pressure: up to 10 bar. Operating temperature: od -10°C up to +70°C. Material: brass nickel-plated.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details

          Coupling push-in reducer, type R8

          All products | Push-in fittings
          0 €
          Coupling push-in reducing, type R8, Intended for connections lines and other element in systems pneumatic. easy and fast in use for repeated mounting without loss tightness po side mechanical and pneumatic. Material: brass nickel-plated. Working pressure: 16 bar. medium working: vacuum, air. Operating temperature: od -20°C up to +80°C. sealing: NBR.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details

          A throttle trigger MWDSE with male thread, brass

          All products | Equipment for pneumatic valves
          0 €
          A throttle trigger MWDSE with thread external used in systems compressed air in order to reducing level noise. Material: brass nickel-plated. Operating temperature: od -10°C up to +80°C. Working pressure: 12 bar.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Head articulated for mounting on piston rod actuator. Do use in case occurrence loads not being in axis piston rod actuator. head articulated gives greater the ability assembly. thread: M4 ÷ M36x2. Material: galvanised carbon steel (head), steel (joint).
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Tee "T" with threads external BSPT type A16, intended for connecting element pneumatics (in this hoses) of each other. tightness connections requires with rules use additional seals. W case thread tapered tape PTFE or sealant, in case thread parallel washers aluminum or copper. Material: brass nickel-plated. Working pressure: 60 bar.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          A universal valve directional o control electric (solenoid valve), without a coil control, used most often for control operation actuators. can be mounted in lines, for a wall, directly for actuators or on block connection. Function 3/2 - three-way, two-position. Material: body valve - aluminum, spool - aluminum nickel-plated, sealing - NBR, Cover end - plastic plastic. Working pressure: up to 10 bar. Operating temperature: -10°C up to +60°C.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Coupling push-in angled 90°, adjustable double with thread external, type R50, Intended for connections lines and other element in systems pneumatic. easy and fast in use for repeated mounting without loss tightness po side mechanical and pneumatic. Material: brass nickel-plated. Working pressure: 16 bar. medium working: vacuum, air. Operating temperature: od -20°C up to +80°C. sealing: NBR.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Flange swivel with double eye for mounting on rear parts cover actuator, of pin. allows performing movement actuator pneumatic during its use. W set: 4 screws with washers, 1 pin, 2 rings securing. Material: aluminum cast (flange), steel+bronze+PTFE (sleeve), steel carbon galvanized (screws and washer), steel carbon galvanized (pin), steel stainless (ring securing).
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          A universal valve type 6560 intended for installation industrial. It can be used for air, gases, water, chemicals, products petrochemical. Material: body - brass nickel-plated, the ball: brass chrome-plated. sealing: the ball - teflon, spindle - NBR. Operating temperature: od -20°C up to +80°C.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Fitting angled 90° adjustable with thread external, type R15, Intended for connections lines and other element in systems pneumatic. easy and fast in use for repeated mounting without loss tightness po side mechanical and pneumatic. Material: brass nickel-plated. Working pressure: 16 bar. medium working: vacuum, air. Operating temperature: od -20°C up to +80°C. sealing: NBR.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details

          Silencer MWSTT with male thread, brass

          All products | Equipment for pneumatic valves
          0 €
          Silencer MWSTT with thread external used in systems compressed air in order to reducing level noise. reducer noise that can obtain through assembly silencer, measured at pressure supply 5 bar, in distance 1m and under angle 45° od axis silencer, is average depending on size 32 dB. Material: brass nickel-plated, bronze sintered nickel-plated. Operating temperature: od -10°C up to +80°C. Working pressure: 12 bar.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Tee "T" 2x female threadint external BSPT, 1xgwint internal BSP type A17, intended for connecting element pneumatics (in this hoses) of each other. tightness connections requires with rules use additional seals. W case thread tapered tape PTFE or sealant, in case thread parallel washers aluminum or copper. Material: brass nickel-plated. Working pressure: 60 bar.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Set seals replaceable for actuator ISO 15552 version: STD, type A, series 3. Material: NBR. Diameter: 32 ÷ 125.
        • Placeholder
          Select options This product has multiple variants. The options may be chosen on the product page / Details
          Miniature valve intended for installation pneumatic, with connections push-in for direct mounting on hoses with plastic o calibrated diameter outer. functionally similar for a ball valve (shut-off flow through rotation a knob o 90º), is however miniature three-way valve spool (3/2) with venting – should go mount in accordance with direction flow marked on body. Po cut-off supply configuration za valve is vented through holes is found in on the top a knob, thanks to which possible is performing repairs and maintenance the system. Material body: plastic plastic. Material spool: brass. seal: O-ring with NBR. Operating temperature: od 0⁰C for +60⁰C.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          Tee "L" 2x female threadint external BSPT, 1xgwint internal BSP type A18, intended for connecting element pneumatics (in this hoses) of each other. tightness connections requires with rules use additional seals. W case thread tapered tape PTFE or sealant, in case thread parallel washers aluminum or copper. Material: brass nickel-plated. Working pressure: 60 bar.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details

          Cap for hoses metric, type PPFM

          All products | Push-in fittings
          0 €
          Cap Intended for flexible hoses pneumatic in sizes metric, series S, type PPFM. Material: plastic plastic. Working pressure: 10 bar. Vacuum: 0.99 bar. Operating temperature: od 0°C up to +60°C.
        • Select options This product has multiple variants. The options may be chosen on the product page / Details
          A cross 3xgwint internal BSP, 1xgwint external BSPT type A20, intended for connecting element pneumatics (in this hoses) of each other. tightness connections requires with rules use additional seals. W case thread tapered tape PTFE or sealant, in case thread parallel washers aluminum or copper. Material: brass nickel-plated. Working pressure: 60 bar.
        Go to Top