Our products
Product categories
Working pressure [bar]
Minimum operating temperature [°C]
Maximum operating temperature [°C]
Material
Vacuum resistance
Standard length [m]
Select options This product has multiple variants. The options may be chosen on the product page / DetailsMedium wall thickness, flexible hose intended for discharge dusts, sawdust, chips, offcuts, light bulk materials etc. Specially designed according to the requirements of the wood and furniture industry, it can also be used in other industries. compliant with the standard DIN 26057 Type 2. Antistatic and flame-retardant, it ensures a high level of work safety. less pliable and compressible than SMARTFLEX® 0.4 and 0.6, za to smooth inside, flexible also in low temperatures. With very good abrasion resistance, also resistant to microbes and hydrolysis. Contains no halogen compounds or plasticisers. Resistant to oils and petrol. The optimal flow direction of the medium is marked with an arrow. The hose wall thickness is measured between the spiral. Assembly on connectors with bridge clamps (prawo-handed). Other diameters may be available on special order. Anti-electrostatic properties: permanently antistatic (in accordance with ISO 8031 resistance R 9 Ω, in accordance with the German technical regulations TRGS 727 (6.4.2.4) specific resistance R 8 Ωm, in accordance with directive 2014/34/EU (ATEX) it can be used in specified explosion-hazard zones - which should be preceded by a risk analysis). After effective two-sided earthing of the spiral, it can be treated as electrically conductive – in accordance with BGI 739-2 recommendations. Flame-retardant – in accordance with DIN 4102 class B1. Hose material: transparent polyether-polyurethane. Wall thickness measured between the spiral: 0.7 mm. Reinforcement: spiral with wire steel. Operating temperature: od -40°C up to +100°C (momentarily up to +125°C).- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThis high-performance suction and discharge hose is engineered for the safe transfer of food products, featuring an odorless and tasteless white natural rubber inner layer that ensures purity and preserves the original flavor of liquids. Free from phthalates and bisphenol A, it fully complies with the strictest international food contact regulations, including 1935/2004/EC, 2023/2006/EC (GMP), D.M. 21/03/73, FDA 21 CFR 177.2600, and BfR XXI cat. 2. Reinforced with a durable synthetic cord and a robust steel spiral, it offers excellent resistance to vacuum, making it ideal for demanding applications in the food and beverage industry. Perfectly suited for milk, dairy products, wine, beer, and fruit juices, it guarantees safe and efficient transfer, though it is not recommended for oils or fatty substances. The abrasion- and weather-resistant blue EPDM outer layer ensures long-lasting performance even in challenging environments, while the hose maintains a reliable working pressure of 6 bar and an operating temperature range from -25°C to +80°C. Designed to combine safety, durability, and flexibility, it is the trusted solution for modern food processing and beverage production facilities.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSemi-transparent, yellow, flexible hose designed specially for fuels and oils lubricating. resistant na swelling and hardening na result operation hydrocarbons, reduces significantly risk cracking and leakage. minimum extractability secures cleanliness fuels, a low factor penetration substances aromatic secures the operator and environment. resistant na ozone and radiation UV. flexibility hose facilitates its installations even in tight places. semi-transparent wall allows na monitoring flow. hose is resistant na most products petroleum-based and fuels (also with addition ethanol for 10%) and can be used for gasoline, kerosene, oil drive and heating, agents lubricating, coolants for cutting and na base glycol. commonly used and proven in thousands applications: small engines, automotive, vehicles recreational, mowers garden, saws, installations coolant and lubrication, equipment for cutting and polishing. Length of a full hose roll 15 m. pressure working determined relative to pressure bursting at factor safety 1:5. Material: PVC (special). Maximum operating temperature: +74°C. temperature brittleness: -37°C. Hardness: 57° Shore (A). Density: 1.26 g/cm 3. Note: The product is packaged in the Tubes International Clean Zone (CLEAN ROOM) in compliance with rigorous standards. Return of the product after opening the package is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA very light, flexible suction-delivery hose intended for conveying chemical substances. made with thermoplastic vulcanizate TPV – material combining advantages processing polymers thermoplastic (PP – polypropylene) with properties vulcanized rubber (EPDM). good resistance chemical - close for rubber EPDM allows na use go for many substances, among others acids (hydrochloric, sulfuric), bases, salts, alcohols, glycols and ketones, concentrated detergents. not recommended for fuels, oils, solvents aromatic. resistant na conditions atmospheric, aging and abrasion (abrasion resistance compliant with ISO 4649:150 mm 3 ). low weight and small radius bending hose ensure ease operation, co can be advantage at transfer with tankers and container. Na special order Available version VACUPRESS SUPER CHEMI (diameter for 63 mm) with layer inner lined polyethylene (LLDPE) co increases resistance chemical hose and allows its use among others for concentrated acids hydrochloric and sulfuric, for acid nitric and for aggressive herbicides and insecticides. Inner layer: thermoplastic rubber TPV. Reinforcement: braid polyester, spiral steel galvanized. Outer layer: thermoplastic rubber TPV. pressure working for temperatures +20°C : od 7 up to 15 bar - depending on diameter hose. temperature use: from -25°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose HYPERLINE FX is optimal solution in use industrial, when required are large flow rates, resistance chemical and temperature, resistance na penetration. perfectly is suitable for conveying substances chemical, fuels, oils, paints, solvents, adhesives, dyes, gases and steam water, detergents, water and substances food. at temperature use above +130°C maximum pressure working given in table should reduced o 1% na each 1°C above tej temperatures. for example at temperature 170°C maximum pressure working for hose AF-FXAM-10 is: 70 bar – (170°C-160°C) x 1 = 70 bar – 40% = 42 bar. W case, when a hose PTFE flows substances, which is poor conductor and has potential properties electrification, charge electric will accumulated na internal surface PTFE and to avoid problem electricity static is used antistatic AS variant PTFE. antistatic teflon in version AS contains appropriate distributed in PTFE graphite and has resistance R 8 Ω (in accordance with the standard ISO 8031 anex A). Material hose: inside smooth, externally Serrated PTFE (teflon) - natural white and antistatic - black. Reinforcement: braid aramid. pressure working: from 35 bar to 77 bar - depending on diameter hose. temperature use: from -70°C to +180°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsColorless, semi-transparent, reinforced a braid flexible hose with rubber silicone vulcanized platinum. intended for higher pressures. used in industry pharmaceutical, cosmetic, food, biotechnology, sterile lines filling, systems treatment water, production vaccines, bioreactors. is characterized exceptionally smooth surface inner prevents deposition and adhesion contamination inside hose and growth bacteria. facilitates to total cleaning and sterilization hose. smooth Layer inner reduces also resistance flow through hose. low extractability, nie toxicity, nie hemolyticity and nie pyrogenicity ensures total cleanliness liquids we sensitive use. minimal level loads biological (bioburden). meets requirements hygienic American FDA 21 CFR 177.2600, 3-A and USP Class VI. possible sterilization steam (30 min, 1 bar, 121°C), cleaning CIP and SIP installations, oxide ethylene or radiation (for 5 Mrad). Length of a full hose roll 15 m (od diameter internal 31.8 mm – 7.5 m). pressure working determined relative to pressure bursting at factor safety 1:4. Material: silicone (platinum). Maximum operating temperature: up to +160°C. temperature brittleness: -80°C. Hardness: 70° Shore (A). Density: 1.18 g/cm³. Note: The product is packaged in the Tubes International Clean Zone (CLEAN ROOM) in compliance with rigorous standards. Return of the product after opening the package is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong, flexible, thick hose intended for discharge sawdust, chips, offcuts, bulk materials etc. Specially designed according to the requirements of the wood and furniture industry, it can also be used in other industries. compliant with the standard DIN 26057 Type 3. Antistatic and flame-retardant, it ensures a high level of work safety. thick wall and dense spiral reinforcing ensure high parameters pressure. very smooth inside, little compressible. flexible also in low temperatures. With very good abrasion resistance, also resistant to microbes and hydrolysis. Contains no halogen compounds or plasticisers. Resistant to oils and petrol. The optimal flow direction of the medium is marked with an arrow. The hose wall thickness is measured between the spiral. Assembly on connectors with bridge clamps (prawo-handed). Other diameters may be available on special order. Anti-electrostatic properties: permanently antistatic (in accordance with ISO 8031 resistance R 9 Ω, in accordance with the German technical regulations TRGS 727 (6.4.2.4) specific resistance R 8 Ωm, in accordance with directive 2014/34/EU (ATEX) it can be used in specified explosion-hazard zones - which should be preceded by a risk analysis). After effective two-sided earthing of the spiral, it can be treated as electrically conductive – in accordance with BGI 739-2 recommendations. Flame-retardant – in accordance with DIN 4102 class B1. Wall thickness measured between the spiral: 1.4 mm. Hose material: transparent polyether-polyurethane. Reinforcement: spiral with wire steel. Operating temperature: od -40°C up to +100°C (momentarily up to +125°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong hose suction - delivery with layer inner with resistant chemical polyethylene o ultra-high weight molecular (UPE, UHMWPE). The inner layer is resistant to most acids and bases and many other aggressive chemicals (in elevated, ale nie very high temperatures), co makes, that hose is wide used in industry chemical and petrochemical. Layer inner with UPE is also compliant with requirements for hoses food, free of phthalates and polycyclic carbon aromatic (PAH), is characterized also low a coefficient friction during flow and prevents deposition medium na walls. This significantly facilitates cleaning and allows use also in the cosmetic, pharmaceutical and food industry. Reinforcement cord synthetic and spiral steel, built-in cable copper for discharge charges electrostatic. Layer outer with resistant chemical rubber EPDM, resistant na abrasion, ozone and conditions atmospheric. compliant with requirements EN 12115:11 (type M, resistance between fitting the line R ≤ 100 Ω, guaranteed for lines o length for 40 m). standards and requirements : hoses chemical: EN 12115:2011. industry food, contact with food (Layer inner): 1935/2004/EC, 2023/2006/EC (GMP), 10/2011/EU (simulant fluids A, B, D2), FDA 21 CFR 177.1520, BfR III. Confirmation of resistance and application conditions requires contact with Tubes International, in particular for temperatures above 50°C. Inner layer: white cream polyethylene UPE. Reinforcement: synthetic cord, steel spiral. Outer layer: black rubber EPDM. pressure working: 16 bar. temperature use: from -40°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThis lightweight and highly flexible suction and discharge hose combines durability with versatility, making it an excellent solution for demanding industrial applications. Its inner layer of transparent polyurethane is resistant to abrasion and oils, while the densely wound steel spiral reinforcement ensures outstanding resistance to vacuum, collapse, and high working pressures ranging from 12 to 20 bar at 20°C. The smooth interior minimizes flow losses, facilitates cleaning, and, together with the transparent wall, allows for continuous visual monitoring of the medium. Designed for air, water, light chemicals, and hydraulic or pneumatic systems, it also performs reliably in the transport of powders, granules, dust, and other abrasive bulk materials. The hose’s small bending radius enhances flexibility in confined spaces, while its chemical resistance makes it suitable for fluids containing fats, oils, or hydrocarbons. Additionally, it meets FDA 21 CFR 177.2600 e, f requirements, enabling safe use in the food industry for both hydrated and fatty food substances. With an operating temperature range from -20°C to +90°C, this hose delivers dependable performance across a wide spectrum of environments, offering a robust and transparent solution for industries seeking efficiency, safety, and reliability.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose Hyperline FX SS RC BLACK to light, flexible hose PTFE, has additional layer external made with black, antistatic and flame-retardant rubber EPDM, meeting (rubber) requirements for vehicles railway EN 45545. ensures to additional cover braid and hose against damage and easy cleaning hose. Ze regard na its properties recommended for applications in industry and vehicles mechanical. hose can be delivered without ends, jak and in the molds complete lines, gorowych for mounting. Material hose: inside smooth, externally Serrated PTFE (teflon). Reinforcement: single braid of steel AISI 304 with additional layer protective with rubber EPDM. pressure working: from 50 bar to 110 bar - depending on diameter hose. temperature use: from -40°C to +140°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, flexible, and highly adaptable, this transparent polyether-polyurethane hose is engineered for efficient suction and transport of light, abrasive materials such as dust, powders, granules, grains, and flakes under low pressure. Its nearly smooth interior ensures optimal flow, while the hard PVC spiral reinforcement provides excellent crush resistance and durability in demanding environments. Resistant to abrasion, ozone, weathering, hydrolysis, and biological corrosion, the hose guarantees long-lasting performance across multiple industries, including food processing, agriculture, plastics, and construction. Certified for temporary contact with dry, bulk, non-fatty foodstuffs, it fully complies with European regulations 1935/2004/EC, 10/2011/EU (simulant E), 1895/2005/EC, 2023/2006/EC (GMP), as well as FDA 21 CFR 177.2600 “d,” making it a safe and reliable choice for food-related applications. Available in standard and antistatic versions, the latter features a copper wire integrated along the spiral to ensure effective grounding and secure electrostatic charge dissipation. With an operating temperature range from -25°C to +85°C, this hose delivers exceptional versatility and performance, making it the ideal solution for industries seeking efficiency, safety, and compliance in material handling.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsColorless, transparent, flexible hose completely free of plasticizers for applications chemical and food - demanding high resistance chemical, of regard na character substances (np. wine – alcohol, acids – sok orange) or used agents cleaning and disinfecting. resistant na acids, bases, salts, alcohols and ketones, o very low level absorption and adsorption. minimizes to risk changing properties, taste and smell liquid even at repeated use hose. glassy smoothed, free of pores surface inner prevents deposition and adhesion contamination inside hose and facilitates its cleaning. resistant na chemical agents cleaning and disinfectant. Not recommended for hydrocarbons. meets requirements hygienic and for contact with food: European 1935/2004/EC and 10/2011 EU (for conditions and substances acc. to certificate), American FDA 21 CFR 177.1520, NSF-51. possible sterilization oxide ethylene or radiation (for 2.5 Mrad). compliant with REACH – nie contains substances hazardous and banned. appropriate combustion used hoses nie causes release hazardous substances (np. hydrogen chloride). hose used both for substances food (np. dispensing wine) jak and chemical: installations detergents, dispensing paints printing, filling accumulators acid, analyzers chemical. Length of a full hose roll 15 m (for diameter internal 25.4 mm – 7.5 m). The given working pressure is determined relative to the bursting pressure at a safety factor of 1:5. Material: polyolefin. temperature use: from -75°C to +54°C. temperature brittleness: -75°C. Hardness: 75° Shore (A). Density: 0.90 g/cm³. Note: The product is packaged in the Tubes International Clean Zone (CLEAN ROOM) in compliance with rigorous standards. Return of the product after opening the package is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong, flexible, hose suction-delivery intended for pressure conveying water, beer, wine, alcohols with a concentration up to 20%, juices, drinks, other liquid substances food and light chemicals. not recommended for milk and its dairy products, oils and greasy substances food. Reinforcement spiral with galvanized wire steel, embedded in layer internal, PVC, ensures good resistance to vacuum and kinking hose. smooth Layer inner reduces losses flow and ensures ease cleaning. thanks to reinforcement a braid hose has high resistance pressure and small deformation under pressure. Standards and requirements: Food industry, food contact: compliant with the European requirements 1935/2004/EC and 10/2011/EU (simulant fluids A, B and C), 2023/2006/EC (GMP). Hose material: transparent PVC. Reinforcement: a polyester braid, steel spiral. Working pressure: from 10 bar to 20 bar, depending on the diameter hose. Vacuum: 0.9 bar. Operating temperature: -5°C up to +65°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery pliable and flexible, A universal hose suction-delivery intended for water, liquids and light chemicals. used for loading and unloading tankers, IBC containers and for conveying liquids in installations industrial, itp. retains high flexibility at sub-zero temperatures ambient. smooth inner wall facilitates maintaining hose in cleanliness and increases unloading efficiency by 20% compared with typical rubber hoses. Layer outer resistant to abrasion and conditions atmospheric. W industry food It can be used for conveying and transfer food hydrated, acidic, alcohols for 20% np. juices, drinks, beer, wine, (simulants A, B, C; up to +40°C and 2 h). Not recommended for milk and dairy products or oils and greasy food substances. hose VACUPRESS SUPERELASTIC complies with the European requirements 1978/142/EEC, 1935/2004/EC, 1895/2005/EC and 10/2011/EU (simulants A, B, C), 2023/2006/EC (GMP). Suitable for temporary contact with food when conveying food substances - under the conditions specified in the manufacturer's declaration of conformity (available at Tubes International). Inner layer: white PVC. Reinforcement: steel spiral, a polyester braid. Outer layer: black PVC. Working pressure at a temperature of 20°C: from 5 bar to 20 bar - depending on the diameter hose. Operating temperature: from -25°C to +60°C. As the working temperature rises, the hose's working pressure value decreases.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsColorless, transparent, strong and flexible hose made with polyester - polyurethane, free of plasticizers, exceptionally resistant na abrasion and tearing, is characterized flexibility even in low temperatures and withstands cyclic changing temperatures. hose manufactured is in strict tolerances dimensional batch for batch, co ensures safe, repeatable connection with fitting. resistant na oils, greases and fuels and range chemicals. strength na conditions atmospheric and intensive daily use. found use in many branches industry: installations fuel and lubricating, for liquids cooling in automotive, for air in pneumatics and automation industrial, for conveying products abrasive and viscous, sludge and powders and as A guard cables electric. length full roll hose 30 m. pressure working determined relative to pressure bursting at factor safety 1:5. Material: tygothane® - polyurethane-polyester (PU). temperature use: from -73°C to +79°C (momentarily up to +93°C). temperature brittleness: -73°C. Hardness: 82° Shore (A). Density: 1.20 g/cm 3. Note: The product is packaged in the Tubes International Clean Zone (CLEAN ROOM) in compliance with rigorous standards. Return of the product after opening the package is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsMedium wall thickness, strong and flexible hose intended for discharge sawdust, chips, offcuts, light bulk materials etc. Specially designed according to the requirements of the wood and furniture industry, it can also be used in other industries. Antistatic and flame-retardant, it ensures a high level of work safety. less pliable and compressible than SMARTFLEX® 0.4, 0.6 and 0.7, za to smooth inside, flexible also in low temperatures. With very good abrasion resistance, also resistant to microbes and hydrolysis. Contains no halogen compounds or plasticisers. Resistant to oils and petrol. The optimal flow direction of the medium is marked with an arrow. The hose wall thickness is measured between the spiral. Assembly on connectors with bridge clamps (prawo-handed). Other diameters may be available on special order. Anti-electrostatic properties: permanently antistatic (in accordance with ISO 8031 resistance R 9 Ω, in accordance with the German technical regulations TRGS 727 (6.4.2.4) specific resistance R 8 Ωm, in accordance with directive 2014/34/EU (ATEX) it can be used in specified explosion-hazard zones - which should be preceded by a risk analysis). After effective two-sided earthing of the spiral, it can be treated as electrically conductive – in accordance with BGI 739-2 recommendations. Flame-retardant – in accordance with DIN 4102 class B1. Wall thickness measured between the spiral: 1.0 mm. Hose material: transparent polyether-polyurethane. Reinforcement: spiral with wire steel. Operating temperature: od -40°C up to +100°C (momentarily up to +125°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery flexible, lighter od rubber, hose suction-delivery intended for conveying water, sewage, sludge and dry bulk materials. used for systems irrigation, loading and unloading tankers, in installations industrial, etc. retains high flexibility at sub-zero temperatures ambient. smooth inner and outer wall facilitates maintaining hose in cleanliness and increases flow capacity unloading o 20%. is resistant to conditions atmospheric and abrasion. hose Available also in straight, not bent in coil sections 3 for 6 m. Inner layer: black PVC. Reinforcement: a polyester braid, galvanised steel spiral. Outer layer: black PVC. Working pressure: from 5 bar to 16 bar - depending on the diameter hose and temperatures. Operating temperature: od -25°C up to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, very flexible hose suction-delivery intended for water, juices, drinks, beer, wine, alcohols with a concentration up to 20% and other products food. not recommended for milk and its dairy products, oils and greasy substances food. Reinforcement with a rigid-PVC spiral, impact-resistant, provides good resistance to vacuum and kinking of the hose. transparent wall allows on easy visual control of the flow. A smooth inner surface reduces flow losses and ensures ease of cleaning. surface outer lightly corrugated. W use not regarding direct contact with food (in industry, construction, agriculture) It can be used: 1) for light chemicals, water, sludge and sewage, other liquids (without fat, oils and hydrocarbons); 2) for air, vacuum conveying dusts, powders, granulates and other lightly abrasive substances bulk (not greasy). In that case the abrasiveness and the possible problem of static electricity must be taken into account. Standards and requirements: Food industry, food contact: compliant with the European requirements 1935/2004/EC and 10/2011/EU (simulant fluids A, B and C), 2023/2006/EC (GMP). Hose material: transparent PVC. Reinforcement: rigid-PVC spiral. Working pressure: from 2 bar to 7 bar, depending on the diameter hose. Operating temperature: from -10°C to +55°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA very light, flexible suction-delivery hose intended for conveying chemical substances. made with thermoplastic vulcanizate TPV – material combining advantages processing polymers thermoplastic (PP – polypropylene) with properties vulcanized rubber (EPDM). good resistance chemical - close for rubber EPDM allows na use go for many substances, among others acids (hydrochloric, sulfuric), bases, salts, alcohols, glycols and ketones, concentrated detergents. not recommended for fuels, oils, solvents aromatic. resistant na conditions atmospheric, aging and ozone. low weight and small radius bending hose ensure ease operation, co can be advantage at transfer with tankers and container. Note: all sizes hose have na branding marking approximate pressure working (WP 10 bar).Confirmation of resistance and application conditions requires contact with Tubes International. Inner layer: thermoplastic rubber TPV. Reinforcement: braid polyester, spiral steel. Outer layer: thermoplastic rubber TPV. pressure working for temperatures +23°C : od 12 up to 14 bar - depending on diameter hose. temperature use: from -30°C to +80°C (pressure working dependent od temperatures).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsColorless, transparent, soft and very flexible hose o exceptionally high service life in use in pumps peristaltic (LFL - „long flex life”). has high resistance fatigue and exceptional resistance na flaking („spallation” - crumbling particles material hose in result pressure rotor pump). one with best hoses TYGON® for pumps peristaltic - service life 1000 h use (at pressure check 0 bar). resistance na flaking particles eliminates need frequent replacement filter and minimizes risk contaminants substances. is suitable for liquids o high viscosity, sticky and liquids sensitive na shearing. wide used in industry food, cosmetic, pharmaceutical and chemical, in production and laboratories. hose free of is phthalates and BPA (bisphenol A). meets requirements hygienic and for contact with food: European 1935/2004/EC and 10/2011 EU (for conditions and substances acc. to certificate), American FDA, NSF, USP Class VI, international ISO 10993, Japanese #370/1959. possible sterilization steam or oxide ethylene. compliant with REACH and California Proposition 65 - nie contains substances hazardous and banned. length full roll hose 7.5 m (od diameter internal 19 mm - 3 m). pressure working determined relative to pressure bursting at factor safety 1:5. Material: PVC (special). Maximum operating temperature: up to +74°C. temperature brittleness: -46°C. Hardness: 56° Shore (A). Density: 1.17 g/cm³. Note: The product is packaged in the Tubes International Clean Zone (CLEAN ROOM) in compliance with rigorous standards. Return of the product after opening the package is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, flexible, pliable and almost smooth inside hose with soft polyvinyl chloride (PVC) reinforced spiral with hard PVC (right-handed). intended for discharge dusts, smoke, fibres, extraction contaminants air etc. used also for discharge condensate in installations air conditioning and as A guard lines and cables. Assembly of the hose with clamps on suitable ends, pipe spigots etc.. The hose wall thickness is measured between the spiral. Hose material: grey, soft PVC. Reinforcement: rigid-PVC spiral. Operating temperature: od -15°C up to +60°C (podworking pressure depends on temperature).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThis lightweight and highly flexible suction and discharge hose is designed for safe transfer of water, juices, soft drinks, beer, wine, alcohols up to 20%, and a wide range of other food products, while its transparent yellowish PVC wall allows continuous visual flow control. Reinforced with a durable hard PVC spiral, it offers excellent resistance to impacts, vacuum, and hose collapse, ensuring reliability in demanding conditions. The smooth inner surface minimizes flow losses and facilitates easy cleaning, while the slightly corrugated exterior enhances flexibility and handling. Certified for food contact in accordance with European regulations 1935/2004/EC, 10/2011/EU, and 2023/2006/EC (GMP), it guarantees safety and compliance in food industry applications. Beyond food use, it is also suitable for industrial, construction, and agricultural environments, where it can handle light chemicals, water, sludges, sewage, air, dust, powders, granules, and other non-fatty bulk materials. For operations where electrostatic discharge may pose a risk, the special antistatic version LUISIANA AS, equipped with an embedded copper wire for grounding, provides additional protection and reliability. With working pressures ranging from 2 to 8 bar depending on diameter and an operating temperature range of -5°C to +60°C, this hose combines versatility, safety, and durability, making it an excellent choice for both food-grade and technical applications.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSuction-delivery hose latest generation specially designed according to high requirements industry processing beer. intended is for conveying high quality beer raw, beer pasteurised and beer organic. The inner layer is free of phthalates, plasticisers and components of animal origin, co eliminates risk contamination medium and growth bacteria. Layer outer resistant to abrasion, aging and conditions atmospheric. tested and approved for conveying beer through Technical University WEIHENSTEPHAN in Munich – not causes changes taste beer. standards and requirements : 1) general: EC 2002/95 (RoHS), EC 1907/2006 (REACH). 2) industry food, contact with food: 1935/2004/EC, 2023/2006/EC (GMP). Layer inner compliant with FDA 21 CFR 177.2600, D.M. 21/03/73, 3-A n. 18-03-Class II. Inner layer: white rubber bromobutyl (BIIR). Reinforcement: cord synthetic, steel spiral. Outer layer: red rubber CR. Working pressure: 10 bar. Operating temperature: -40°C up to +120°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThis ultra-lightweight and highly flexible hose is engineered for maximum performance in demanding environments, ensuring reliable extraction of dust, powders, fumes, vapors, and contaminated air. Its innovative dual-layer soft PVC structure, reinforced with synthetic fibers and a PVC-coated steel spiral, guarantees exceptional durability, resistance to kinking, and impressive tensile strength, even under intensive use. The unique design with longitudinal and transverse reinforcement provides a minimal bending radius, making it easy to maneuver in tight spaces while maintaining full functionality. Safe and compliant with BGR 132, the hose is cadmium-free and allows for safe discharge of static electricity through grounding of the steel spiral. The left-handed reinforcing spiral enables secure connection with compatible fittings, including PVC accessories designed for SUPERELASTIC hoses, ensuring a perfect fit for industrial and household vacuum systems. Ideal for construction sites, workshops, and cleaning or drying applications, it also serves as a protective hose in various technical installations. With a temperature resistance from 0°C to +85°C, this versatile solution adapts to a wide range of working conditions, offering long-lasting reliability and efficiency. Easy to mount with clamps, pipe fittings, or specialized connectors, it is the perfect choice for professionals seeking a robust, flexible, and safe hose solution.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe highest quality hose suction-delivery, intended for conveying aggressive substances chemical, solvents and concentrated chemicals, characterized by high strength thermal and mechanical and highest cleanliness layer internal. Layer inner with white polymer perfluoroalkoxy MFA (polymer fluorine o properties close for PTFE), mirror smooth (prevents deposition medium na walls and is easy in maintaining cleanliness), free of smell and taste, meeting high requirements hygienic (FDA, USP, European EU). layer intermediate with rubber synthetic, contain Reinforcement with cord synthetic, spiral with wire steel. outer Layer with rubber EPDM, antistatic (R 6 Ω ), resistant na abrasion, ozone and conditions atmospheric. hose is characterized excellent resistance chemical and cleanliness MFA, impermeability, resistance na temperature, oxidation and stresses mechanical. wide used in industry chemical of regard na total resistance na operation greater substances chemical. appropriate for conveying concentrated acids and alkalis (acid sulfuric, hydrochloric, phosphoric, nitric, lye sodium, potassium itp.). resistant na rigorous conditions cleaning method Cleaning-in-Place (CIP). Na special order version M according to EN 12115 with built-in two cables copper ensuring discharge charges electrical. standards and requirements: hoses chemical: EN 12115:2011 (type Ω). industry food, contact with food: 1935/2004/EC, 2023/2006/EC (GMP); Inner layer: 10/2011/EU, USP Class VI, FDA 21 CFR 177.1550 (e-and); ISO 10993. Nie contains plasticizers, phthalates ani substances origin animal. assembly: should use fitting with a spigot ("tail" for hose) smooth, not having sharp or high notches, which could po crimping cut or damage layer inner with MFA. The spigot diameter should be precisely matched to the hose diameter to ensure tightness. Assembly with clamping ferrules or shell clamps. Confirmation of resistance and application conditions requires contact with Tubes International. Inner layer: white polymer MFA. Reinforcement: synthetic cord, steel spiral. Outer layer: black rubber EPDM. pressure working: 16 bar. temperature use: from -50°C to +170°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsConnector hose SUPERFLEX RADIATOR intended for systems cooling engine in vehicles and engines type automotive (for water, liquids cooling na base glycol ethylene). version of reinforcement textile and a spiral steel securing against collapse bent hose. has „soft” fitting, free of spiral steel, enabling easy and tight installing na spigots using straps. serrated externally The design hose bends easily, replacing in many cases original formed connector and ensuring unobstructed solid flow even at strong bending. The design a connector corresponds standard SAE J20 R5 and is resistant na temperature and na fluids cooling used in automotive. no data regarding pressure working. Operating temperature: from -40°C to +125°C. Material a connector: black rubber EPDM. Reinforcement: textile braid + A spiral steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery light and flexible hose intended for discharge air, dust, dusts, fine sawdust and chips, very light bulk materials etc. Specially designed according to the requirements of the wood and furniture industry, it can also be used in other industries. compliant with the standard DIN 26057 Type 1. Antistatic and flame-retardant, it ensures a high level of work safety. very pliable and compressible, flexible also in low temperatures. With very good abrasion resistance, also resistant to microbes and hydrolysis. Contains no halogen compounds or plasticisers. Resistant to oils and petrol. The optimal flow direction of the medium is marked with an arrow. The hose wall thickness is measured between the spiral. Assembly on connectors with bridge clamps (prawo-handed). Other diameters may be available on special order. Anti-electrostatic properties: permanently antistatic (in accordance with ISO 8031 resistance R 9 Ω, in accordance with the German technical regulations TRGS 727 (6.4.2.4) specific resistance R 8 Ωm, in accordance with directive 2014/34/EU (ATEX) it can be used in specified explosion-hazard zones - which should be preceded by a risk analysis). After effective two-sided earthing of the spiral, it can be treated as electrically conductive – in accordance with BGI 739-2 recommendations. Flame-retardant – in accordance with DIN 4102 class B1. Hose material: transparent polyether-polyurethane. Reinforcement: spiral with wire steel. Wall thickness measured between the spiral: 0.4 mm. Operating temperature: od -40°C up to +100°C (momentarily up to +125°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, colorless, clear, flexible hose free of smell and taste, non-toxic, nie containing phthalates DEHP. designed specially for use in pumps peristaltic. used for dispensing and portioning cold and hot products food, for soaps and detergents, for paints and in laboratories. soft Material hose (60° Shore (A)) is very flexible and ensures very good service life over 500 hours use in pump peristaltic. hose is good alternative for used often hoses, PVC or silicone. is flexible even in temperature -40°C and withstands elevated temperature up to +121°C. has good resistance chemical na range substances chemical, np. acids and bases. Nie recommended for fats, high-percentage alcohols and hydrocarbons. resistant na ozone, oxygen and light solar, flame-retardant. is characterized low extractability (penetration components material for medium). meets requirements hygienic and for contact with food: European 10/2011 EU (for conditions and substances acc. to certificate), American FDA, NSF-51. possible sterilization steam, oxide ethylene or radiation. Length of a full hose roll 15 m. pressure working determined relative to pressure bursting at factor safety 1:5. Material: tygoprene® - thermoplastic elastomer styrene (TPE). Maximum operating temperature: up to +121°C. temperature brittleness: -66°C. Hardness: 60° Shore (A). Density: 0.9 g/cm³. Note: The product is packaged in the Tubes International Clean Zone (CLEAN ROOM) in compliance with rigorous standards. Return of the product after opening the package is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLow-pressure hose suction-delivery with transparent layer inner with resistant chemical PFA and thick layer external with transparent silicone. intended for various applications in industry pharmaceutical, cosmetic, food and chemical, where besides the highest cleanliness, asepsis and resistance chemical required is observation flow medium. Layer inner with polymer perfluoroalkoxy PFA (polymer fluorine o properties close for PTFE), transparent, mirror smooth, free of smell and taste, inert chemical, meeting high requirements hygienic (FDA, USP, European EU). Reinforcement spiral of steel stainless ensures good resistance na vacuum. thick Layer outer with silicone cross-linked compounds platinum o smooth surface features properties nie adhesion (hose nie „adhesives ”) and small a coefficient friction. can be easily purified at use weak detergent. The design hose combines advantages PFA with flexibility silicone and its resistance na temperature. hose has small minimal radius bends, is flexible and flexible in low and elevated temperatures, resistant na cyclic bending in accordance with ASTM D 2176 and na loads dynamic. standards and requirements hygienic: Inner layer: USP Class VI, 3-A Sanitary Standards 18-03 Class I, 10/2011/EU, FDA, ISO 10993-4, -10, -11, non-cytotoxic (ISO 10993 Part 5), ICH Q3D; Outer layer: USP Class VI, 3-A Sanitary Standards 18-03 Class I, D.M. 21/03/73, FDA, BfR, European Pharmacopoeia 3.1.9, ISO 10993-4, -10, -11, non-cytotoxic (ISO 10993 Part 5). hose compliant with 1935/2004/EC, 2023/2006/EC (GMP), made in Cleanroom ISO 14644-1 Class 8, nie contains phthalates, adipates, nitrosamines, substances origin animal, substances subject EC 1907/2006 (REACH). Confirmation of resistance and application conditions requires contact with Tubes International. For confirmation of resistance and conditions of use, please contact Tubes International. assembly: should use fitting with a spigot („tail” for hose) smooth, not having sharp or high notches, which could po crimping cut or damage layer inner with PFA. The spigot diameter should be precisely matched to the hose diameter to ensure tightness. assembly ferrules clamping or hose clamps (clamps). Inner layer: transparent polymer PFA. Reinforcement: spiral of steel stainless AISI 302. Outer layer: transparent silicone. pressure working: from 1 bar to 3 bar, depending on diameter hose. temperature use: from -30°C to +150°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, flexible and smooth with small grooves inside hose with soft polyvinyl chloride (PVC), reinforced spiral with hard PVC (right-handed). intended for extraction contaminants air, smoke, discharge dusts, chips, fibres in industry textile etc. widely used in various use industrial. self-extinguishing and flame-retardant, in accordance with American class flammability UL 94 V-2. Assembly of the hose with clamps on suitable ends, pipe spigots etc.. Wall thickness measured between the spiral. Hose material: soft grey PVC. Reinforcement: rigid-PVC spiral. Operating temperature: od -10°C up to +60°C (podworking pressure depends on temperature).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, very flexible hose suction-delivery intended for conveying water, juices, drinks and other products food in temperature up to +40°C. The absence of phthalates in the hose material recommends it for conveying milk and dairy products and alcohols with a concentration up to 50% and a temperature up to +40°C. not recommended for oils and greasy substances food. Reinforcement spiral with wire steel, embedded in wall with soft PVC, ensures good resistance to vacuum and kinking hose. smooth wall inner reduces losses flow and ensures ease cleaning. transparent wall resistant to radiation UV allows on easy visual control of the flow. W use not regarding direct contact with food (in industry, construction, agriculture) It can be used: 1) for light chemicals, water, sludge and sewage, other liquids (without fat, oils and hydrocarbons); 2) for air, vacuum conveying dusts, powders, granulates and other lightly abrasive substances bulk (not greasy). In that case the abrasiveness and the possible problem of static electricity must be taken into account. as hose reinforced only spiral steel (without braid) is characterized a certain elongation under pressure, co should take into account in use, especially in temperatures above +40°C. Standards and requirements: Food industry, food contact: compliant with the European requirements 1935/2004/EC and 10/2011/EU (simulant fluids A, B, C and D1), 2023/2006/EC (GMP). Hose material: transparent PVC. Reinforcement: galvanised steel spiral. Working pressure: from 2 bar to 12 bar, depending on the diameter hose. Vacuum: 0.9 bar. Operating temperature: from -15°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsExceptionally pliable and flexible hose suction-delivery intended for conveying substances food, requiring the use of rubber free of odour and taste. Contains no phthalates or bisphenol A. Suitable for milk and dairy products, as well as wine, beer, fruit juices. not recommended for oils and greasy substances food. commonly used in road tankers for handling milk. Due to high flexibility It can be used for hose reels drum. Layer outer hose resistant to abrasion and conditions atmospheric. Standards and requirements: Food industry, food contact: 1935/2004/EC and 2023/2006/EC (GMP), D.M. 21/03/73, FDA 21 CFR 177.2600, BfR XXI kat. 2. Inner layer: white rubber natural (NR). Reinforcement: cord synthetic, steel spiral. Outer layer: blue EPDM rubber. Working pressure: 6 bar. Operating temperature: -25°C up to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong, flexible hose medium wall thickness, intended for discharge chips, bulk materials, granulate etc. Dla all types industry, in particular often used for discharge chips and other particles solid in industry wood, furniture, ceramic, plastics. wall medium wall thickness and dense spiral reinforcing ensures higher parameters pressure in ratio for hoses ECO 0.4, 0.6 and 0.7. very smooth inside, little compressible and flexible - also in low temperatures. O sound resistance to abrasion, resistant also on microbes and hydrolysis. Not toxic, Contains no halogen compounds or plasticisers. Resistant to oils and petrol. hose marked is an arrow indicating correct direction flow medium. The hose wall thickness is measured between the spiral. Assembly on connectors with bridge clamps (prawo-handed). Other diameters may be available on special order. hose Available is in following versions: ECO – version standard, ECO SE – version with material flame-retardant (UL94 V-2), ECO AS – version permanently antistatic (ISO 8031: R 9 Ω, TRGS 727 (6.4.2.4): R 8 Ωm, directive 2014/34/EU (ATEX): It can be used in defined zones hazard explosion po analysis risk, ECO SE AS – version antistatic and flame-retardant (Available on special order). hose ECO produced is in process production compliant with with policy sustainable growth in which uses raw materials originating with recycling pure waste with process production, energy renewable, closed circulation water and other innovation. Hose material: transparent polyether-polyurethane. Reinforcement: spiral with wire steel. Wall thickness measured between the spiral: 1.0 mm. Operating temperature: od -40°C up to +100°C (momentarily for + 125°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose of reinforcement spiral steel, intended for hot water mixed with fluids anti-freeze. used for systems cooling and heating, for pumps in engines and machines. has resistance to vacuum. Layer inner resistant to heat and fluids cooling. Layer outer resistant to heat and aging. blend rubber compliant with the standard DIN 73411:79. Inner layer: black EPDM rubber. Reinforcement: cord synthetic, steel spiral. Outer layer: black EPDM rubber. Working pressure: 4 bar. Operating temperature: od -40°C up to +120°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCrystalline transparent, flexible and completely biocompatible hose medical free of phthalates (DEHP). intended for use in equipment for performing dialysis, for transfusion and draining blood, infusion, chemotherapy, inhalation, procedures minimally invasive, catheters, laboratories medical. can be used for pumps peristaltic, ale service life nie is large. high transparency hose and nie wettability surface internal ensures good visualization flow and easy total emptying hose. can be joined clamps mechanical, welded thermally, ultrasound or glued. compliant with requirements ISO 10993, European Pharmacopoeia 3.1.1.2, USP Class VI and REACH. is completely nie cytotoxic, nie hemolytic and nie pyrogenic. sterilization steam in autoclaves, oxide ethylene or radiation (for 2.5 Mrad). Length of a full hose roll 15 m. available are hoses medical o other hardness np. TYGON® ND100-80 (hardness 80° Shore (A)). The given working pressure is determined relative to the bursting pressure at a safety factor of 1:5. Material: PVC (special, without DEHP). Maximum operating temperature: +74°C. temperature brittleness: -42°C. Hardness: 65° Shore (A). Density: 1.19 g/cm³. Note: The product is packaged in the Tubes International Clean Zone (CLEAN ROOM) in compliance with rigorous standards. Return of the product after opening the package is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose suction-delivery, intended for conveying wine, beer, juices fruit, alcohols with a concentration up to 96% and other substances food free of fats. The inner layer is free of phthalates, plasticisers and components of animal origin. Contains no phthalates or bisphenol A and no polycyclic aromatic hydrocarbons (PAH Free), in accordance with ZEK 01.4-08 Cat.1. Tested for the presence of heavy metals. thanks to external corrugation hose is exceptionally pliable and flexible. outer surface hose with material thermoplastic o properties slippery fabric has very low factor friction, co additional facilitates operating a hose and eliminates friction o other hoses and element equipment. recommended way mounting with fitting are special clamp shell EASY SHELL, o shape adapted for serrated hose. standards and requirements : industry food, contact with food 1935/2004/EC and 2023/2006/EC (GMP). Layer inner compliant with FDA 21 CFR 177.2600, BfR XXI kat. 2, D.M. 21/03/73. Inner layer: white, smooth rubber butyl (IIR). Reinforcement: cord synthetic, steel spiral. Outer layer: red synthetic rubber with coating thermoplastic. Working pressure: 10 bar. Vacuum: 0.6 bar. Operating temperature: from -40°C to +120°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSpecialized hose suction-delivery for water and sewage in installations sanitary na ships, boats motor, yachts, itp. hose odorless and impermeable odors of drainage sewage na outside (5-year warranty). Layer outer resistant na factors marine and conditions atmospheric. has resistance na vacuum. compliant with the standard EN ISO 8099. Na special order Available version SANITARY STAR / 7 o pressure working 7 bar. length standard: 60 m or 120 m. Inner layer: white rubber synthetic. Reinforcement: braid synthetic, spiral steel. Outer layer: white rubber synthetic. Operating temperature: from -30°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, flexible hose intended for discharge air, dust, dusts, sawdust, fine chips, light bulk materials etc. Dla all types industry, in particular often used for dedusting and discharge fine particles solid in industry wood, furniture, ceramic, plastics. pliable and flexible, also in low temperatures. compressible, smoother inside in comparison hose ECO 0.4. O sound resistance to abrasion, resistant also on microbes and hydrolysis. non-toxic, Contains no halogen compounds or plasticisers. Resistant to oils and petrol. hose marked is an arrow indicating correct direction flow medium. The hose wall thickness is measured between the spiral. Assembly on connectors with bridge clamps (prawo-handed). Other diameters may be available on special order. hose Available is in following versions: ECO – version standard, ECO SE – version with material flame-retardant (without classification flame retardancy), ECO AS – version permanently antistatic ISO 8031: R 9 Ω, TRGS 727 (6.4.2.4): R 8 Ωm, directive 2014/34/EU (ATEX): It can be used in defined zones hazard explosion po analysis risk, ECO SE AS – version antistatic and flame-retardant (Available on special order). hose ECO produced is in process production compliant with with policy sustainable growth in which uses raw materials originating with recycling pure waste with process production, energy renewable, closed circulation water and other innovation. Hose material: transparent polyether-polyurethane. Reinforcement: spiral with wire steel. Wall thickness measured between the spiral: 0.6 mm. Operating temperature: od -40°C up to +100°C (momentarily for + 125°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose suction - delivery for conveying almost all aggressive substances chemical. designed specially for industry petrochemical for fuels o high concentration carbon aromatic, hot oil and solvents. Ze regard na high general resistance chemical rubber FKM can be used for aggressive chemicals, in many cases also in elevated temperatures. used for transfer chemicals with tankers road and railway. Layer inner with smooth black rubber fluorine FKM. Reinforcement cord synthetic and spiral steel. Layer outer with rubber chloroprene CR, antistatic, resistant na conditions atmospheric, ozone, abrasion and oils. built-in two copper cable for discharge charges electrostatic. compliant with EN 12115:11 (type M). Confirmation of resistance and application conditions requires contact with Tubes International, in particular for temperatures above 50°C. Vacuum: 0.9 bar. Inner layer: black rubber FKM (FPM, Viton). Reinforcement: synthetic cord, steel spiral. Outer layer: black rubber CR. pressure working: 16 bar. temperature use: from -25°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong, thick, flexible hose intended for extraction and conveying powders, grains, light granulates and other bulk materials in industry food and pharmaceutical. used m.in. for milk in powder, grain, rice, coffee, tea, flour (version PAS). fairly pliable, little compressible, smooth inside, flexible also in low temperatures. resistant on abrasion, resistant to microbes and hydrolysis. non-toxic, Contains no halogen compounds or plasticisers. Resistant to oils and petrol. Assembly on connectors with bridge clamps (prawo-handed). Other diameters may be available on special order. versions: P7 M PU FOOD – standard, spiral with wire steel; P7 M PU PAS FOOD – spiral of steel stainless, Material hose permanently antistatic (R ≤10 8 Ω, in accordance with TRGS 727). hoses P7 M PU FOOD and P7 M PU PAS FOOD are compliant with requirements European 1935/2004/EC and 10/2011/EU (simulant E), 2023/2006/EC (GMP) and American FDA 21 CFR 177.2600 and 178.2010. are suitable for time contact with food at conveying dry, bulk, free of fat on surface, substances food - on conditions defined in declaration conformity the manufacturer (Available in Tubes International). Hose material: transparent polyether-polyurethane. Wall thickness measured between the spiral: 1.4 mm. Reinforcement: spiral with wire steel (P7 M PU FOOD), spiral with wire of steel stainless AISI 301 (P7 M PU PAS FOOD). Operating temperature: od -40°C up to +100°C (momentarily for + 125°C).
