Our products
Product categories
Working pressure [bar]
Minimum operating temperature [°C]
Maximum operating temperature [°C]
Material
Vacuum resistance
Standard length [m]
Select options This product has multiple variants. The options may be chosen on the product page / DetailsCream - beige flexible hose reinforced a braid polyester free of smell and taste, non-toxic. resistant na temperature in wide the scope from -60°C to +135°C. flexible and flexible, resistant na deformation and abrasion. used for pressure conveying, dispensing and portioning cold and hot products food, for soaps, detergents and agents disinfecting, for paints and toners, pesticides and fertilizers. hose is alternative for used often hoses, PVC or silicone. It has good chemical resistance to a range of chemical substances, especially acids and bases, oxidizing agents jak np. water oxidized, hypochlorite sodium czy ozone. resistant na range fats animal and vegetable. Not recommended for hydrocarbons. resistant na aging and radiation UV. meets requirements hygienic and for contact with food - American FDA 21 CFR 177.2600, NSF-51 and 3-A. possible multiple sterilization steam in autoclaves, cleaning CIP and SIP installations, oxide ethylene or method radiation. Length of a full hose roll 15 m. pressure working determined relative to pressure bursting at factor safety 1:4. Material: norprene® - thermoplastic elastomer (TPE). Maximum operating temperature: up to +135°C. temperature brittleness: -60°C. Hardness: 61° Shore (A). Density: 0.98 g/cm³. Note: The product is packaged in the Tubes International Clean Zone (CLEAN ROOM) in compliance with rigorous standards. Return of the product after opening the package is not possible.- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe highest quality hose suction-delivery intended for conveying very wide range aggressive substances chemical. wide use hose, primarily in industry chemical, conditioned is excellent resistance polymer fluorine FEP na aggressive solvents and concentrated lyes and acids such jak: acid hydrochloric, sulfuric, phosphoric, nitric and lye sodium and potassium. hose can be used also in industry food and pharmaceutical. readily used is in zones pure. Layer inner with white copolymer tetrafluoroethylene / fluoropropylene FEP (thermoplastic polymer fluorine o properties close for PTFE), mirror smooth (prevents deposition medium na walls and is easy in maintaining cleanliness), free of smell and taste, meeting high requirements hygienic (FDA, USP Class VI). layer intermediate with white rubber synthetic, contain Reinforcement with cord synthetic, spiral with wire steel and two copper cable for discharge charges electrostatic. outer Layer with orange rubber EPDM, resistant na abrasion, ozone and conditions atmospheric. hose is characterized excellent resistance chemical and cleanliness FEP and exceptional resistance na temperature. specially designed for cleaning method Cleaning-in-Place (CIP), in this for sterilization steam 150ºC. standards and requirements: hoses chemical: EN 12115:2011(type M). industry food, contact with food (Layer inner): USP Class VI, FDA 21 CFR 177.1550. Confirmation of resistance and application conditions requires contact with Tubes International. Inner layer: white, smooth FEP. Reinforcement: synthetic cord, steel spiral. Outer layer: orange smooth rubber EPDM. pressure working: 16 bar. Vacuum: 0.9 bar. temperature use: from -40°C to +150°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong, flexible hose o thick wall, intended for discharge chips, bulk materials, granulate etc. Dla all types industry, in particular often used for discharge chips and other particles solid in industry wood, furniture, ceramic, plastics. thick wall and dense spiral reinforcing ensure high parameters pressure. very smooth inside, little compressible and flexible - also in low temperatures. O excellent resistance to abrasion, resistant also on microbes and hydrolysis. Not toxic, Contains no halogen compounds or plasticisers. Resistant to oils and petrol. hose marked is an arrow indicating correct direction flow medium. The hose wall thickness is measured between the spiral. Assembly on connectors with bridge clamps (prawo-handed). Other diameters may be available on special order. hose Available is in following versions: ECO – version standard, ECO SE – version with material flame-retardant (UL94 V-2), ECO AS – version permanently antistatic (ISO 8031: R 9 Ω, TRGS 727 (6.4.2.4): R 8 Ωm, directive 2014/34/EU (ATEX): It can be used in defined zones hazard explosion po analysis risk, ECO SE AS – version antistatic and flame-retardant (Available on special order). hose ECO produced is in process production compliant with with policy sustainable growth in which uses raw materials originating with recycling pure waste with process production, energy renewable, closed circulation water and other innovation. Hose material: transparent polyether-polyurethane. Reinforcement: spiral with wire steel. Wall thickness measured between the spiral: 1.4 mm. Operating temperature: od -40°C up to +100°C (momentarily for + 125°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong hose suction-delivery intended for conveying liquid chemicals, in this aggressive acids, bases, alcohols and other detergents used for cleaning installations in plants food (selection in accordance with rules acc. to chapter „hoses chemical” this catalogue). Layer inner with UPE compliant with requirements FDA for contact with food. Widely used in industry food, cosmetic, chemical and petrochemical. has copper cable ensuring continuity electrical between fitting hose. Layer outer resistant to abrasion, ozone and conditions atmospheric. compliant with requirements EN 12115:11 (type M, resistance between fitting the line R ≤ 100 Ω, guaranteed for lines o length for 40 m). standards and requirements : 1) hoses chemical EN 12115:2011. industry food, contact with food (Layer inner) 1935/2004/EC, 2023/2006/EC (GMP), 10/2011/EU (simulant fluids A, B, D2), FDA 21 CFR 177.1520, BfR III. assembly : smooth ends with a spigot ("tail" into the hose) must be used, without sharp or high barbs that could cut or damage the UPE inner layer after clamping. The spigot diameter should be precisely matched to the hose diameter to ensure tightness. Assembly with clamping ferrules or shell clamps. Inner layer: white polyethylene UPE. Reinforcement: cord synthetic, steel spiral. Outer layer: blue EPDM rubber. Working pressure: 16 bar. Vacuum: 0.8 ÷ 0.9 bar - depending on the diameter hose. Operating temperature: -30°C up to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsColorless, glassy transparent, flexible hose free of smell and taste, non-toxic, nie containing phthalates and BPA (bisphenol A). intended for conveying and dispensing products food, in particular products milk, spices, concentrates vitamin, aromas itp. smooth, non-porous surface inner hose eliminates problem settling particles product and growth bacteria. resistant na action alkaline agents cleaning. can be used for pumps peristaltic (service life moderate). meets requirements hygienic and for contact with food: European 1935/2004/EC and 10/2011 EU (for conditions and substances acc. to certificate), American FDA, NSF-51, NSF-61, 3-A, Japanese #370/1959 and MHLW370(3-D). possible sterilization steam or oxide ethylene. compliant with REACH and California Proposition 65 – nie contains substances hazardous and banned. Length of a full hose roll 15 m (od diameter internal 50.8 mm - 6 m). pressure working determined relative to pressure bursting at factor safety 1:5. Material: PVC (special). Maximum operating temperature: +74°C. temperature brittleness: -36°C. Hardness: 66° Shore (A). Density: 1.21 g/cm 3. Note: The product is packaged in the Tubes International Clean Zone (CLEAN ROOM) in compliance with rigorous standards. Return of the product after opening the package is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight and very flexible even in low temperature hose suction-delivery, intended for applications general-industrial (in industry, construction, agriculture). It can be used for water, light chemicals, sludge and sewage, agents protection plants, other liquids (without fat, oils and hydrocarbons) as well as for air, vacuum conveying dusts, powders, granulates and other lightly abrasive substances bulk (non-greasy). In that case the abrasiveness and the possible problem of static electricity must be taken into account. Reinforcement with a rigid-PVC spiral, impact-resistant, provides good resistance to vacuum and kinking of the hose. A smooth inner surface reduces flow losses and ensures ease of cleaning. The outer surface is lightly corrugated, smooth for small diameters. As a hose reinforced only with a rigid-PVC spiral, without a braid, it shows a certain elongation under pressure, which must be taken into account in use, especially at elevated temperatures. Hose material: green transparent PVC. Reinforcement: rigid-PVC spiral. Working pressure at a temperature of 20°C: from 2 bar to 6.5 bar - depending on the diameter hose. As the working temperature rises, the hose's working pressure value decreases. Operating temperature: from -25°C to +55°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery strong, thick, flexible hose intended for extraction and conveying abrasive bulk materials, granulates, gravelling roofs, cleaning industrial, abrasive for sandblasting, silos, tankers for bulk materials etc. compliant with the standard DIN 26057 Type 4 (SMARTFLEX® 2.0). Antistatic and flame-retardant, it ensures a high level of work safety. thick wall and dense, thick spiral reinforcing ensures high resistance to vacuum. smooth inside, non-compressible, not very pliable, but flexible, also in low temperatures. With very good abrasion resistance, also resistant to microbes and hydrolysis. Contains no halogen compounds or plasticisers. Resistant to oils and petrol. The optimal flow direction of the medium is marked with an arrow. The hose wall thickness is measured between the spiral. Other diameters may be available on special order. Anti-electrostatic properties: permanently antistatic (in accordance with ISO 8031 resistance R 9 Ω, in accordance with the German technical regulations TRGS 727 (6.4.2.4) specific resistance R 8 Ωm, in accordance with directive 2014/34/EU (ATEX) it can be used in specified explosion-hazard zones - which should be preceded by a risk analysis). Po effective both earthing spiral can be treated as conductive electrically – in accordance with recommendations BGI 739-2. Flame-retardant – in accordance with DIN 4102 class B1. Wall thickness measured between the spiral: 2.0 mm (SMARTFLEX® 2.0), 2.5 mm (SMARTFLEX® 2.5). Hose material: transparent polyether-polyurethane. Reinforcement: spiral with wire steel. Operating temperature: od -40°C up to +100°C (momentarily up to +125°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible hose suction-delivery intended for conveying food, pharmaceutical and cosmetic substances: water, fruit juices, beer, wine, vinegar, alcohols with a concentration up to 96%, milk and dairy products, creams, soaps, aromatic substances, pigments and others. Resistant to fats and oils within the standard range of use. Good chemical resistance to light chemicals – acid and base solutions. The extruded, completely smooth inner and outer surface of the hose facilitates flow and cleaning. Reinforcement spiral with stainless wire steel, embedded in wall with TPE-S, makes go resistant to vacuum and kinking. transparent wall allows on easy visual control of the flow. The hose material is not vulcanised, is clean (contains no vulcanising additives), resistant to hydrolysis, does not promote bacterial growth, with low porosity and low permeability. Completely neutral in taste and odour, does not change the organoleptic properties of the medium. resistant to aging, conditions atmospheric and radiation UV. Cleaning by the SIP method, which noticeably shortens the service life, is not recommended. Use for high-proof alcohol (its vapours or other flammable substances) requires taking into account the hazards associated with static electricity. as hose reinforced only spiral (without braid) is characterized a certain elongation under pressure, therefore maximum pressure working hose is low (factor safety 1:5). Cleaning, disinfection or sterilisation of the hose must be carried out strictly according to the recommendations given in the catalogue sheet below. standards and requirements : 1) industry food, contact with food: compliant with the European requirements 1935/2004/EC and 10/2011/EU (simulant fluids A, B, C, D1, D2), 2023/2006/EC (GMP) and American FDA 21 CFR 177.2600 „e”. 2) Pharmaceutical industry: USP CLASS VI. Hose material: transparent TPE-S. Reinforcement: spiral of steel AISI 302. Working pressure: from 1 bar to 1.5 bar, depending on the diameter hose. Operating temperature: -30°C up to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery strong, thick, flexible hose intended for extraction and conveying abrasive bulk materials: granulates, grain, sand, gravel. thick wall and very dense spiral reinforcing ensures high resistance to pressure and vacuum. very smooth inside, non-compressible, not very pliable (r=4xD), retains its flexibility also in low temperatures. hose o sound resistance to abrasion, resistant also on oils and gasoline. Assembly on connectors with bridge clamps (prawo-handed) or assembly special on ends industrial e.g. flange. Other diameters may be available on special order. versions: P3 S PU – version standard, with polyester – polyurethane, very resistant to abrasion and P3 S PU AE - version with polyether – polyurethane, o sound resistance to abrasion, resistant to microbes and hydrolysis; with approval for contact with substances food, compliant with requirements European 1935/2004/EC and 10/2011/EU (simulant E), 2023/2006/EC (GMP) and American FDA 21 CFR 177.2600 and 178.2010. is suitable for time contact with food at conveying dry, bulk, free of fat on surface, substances food - on conditions defined in declaration conformity the manufacturer (Available in Tubes International); P3 S PU AS – version antistatic (R ≤10 8 Ω), compliant with TRBS 2153 and for extraction also with TRGS 727, with polyether – polyurethane, o sound resistance to abrasion, resistant to microbes and hydrolysis. Hose material: transparent polyester-polyurethane (P3 S PU), transparent polyether-polyurethane (P3 S PU AE and P3 S PU AS). Wall thickness measured between the spiral: 2 mm. Reinforcement: dense spiral with wire steel. Operating temperature: od -40°C up to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose suction-delivery intended for conveying products pharmaceutical, cosmetic, substances food, chemical (selection in accordance with rules acc. to chapter "hoses chemical"). Contains no plasticisers, phthalates or substances of animal origin. is characterized high strength thermal and mechanical. is excellent solution for industries processing demanding highest safety during transfer products o high cleanliness. Layer outer resistant to abrasion, ozone and conditions atmospheric. has two copper cable ensuring continuity electrical between fitting hose. standards and requirements : 1) general EC 2002/95 (RoHS), EC 1907/2006 (REACH). 2) industry food, contact with food 1935/2004/EC and 2023/2006/EU (GMP). Layer inner compliant with 10/2011/EC, D.M. 21/03/73, FDA 21 CFR 177.1550. Layer outer compliant with FDA 21 CFR 177.2600, D.M. 21/03/73. 3) Pharmaceutical industry: USP CLASS VI (Layer inner). assembly : smooth ends with a spigot ("tail" into the hose) must be used, without sharp or high barbs that could cut or damage the MFA inner layer after clamping. The spigot diameter should be precisely matched to the hose diameter to ensure tightness. Assembly with clamping ferrules or shell clamps. Inner layer: smooth polymer fluorine MFA. Reinforcement: cord synthetic, steel spiral. Outer layer: smooth EPDM rubber. Working pressure: 10 bar. Vacuum: 0.9 bar. Operating temperature: -50°C up to +170°C (for greater chemicals).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible, strong hose suction - delivery intended for water, sewage. externally Serrated, inside almost smooth. good resistance to external impacts and heavier conditions use. retains high flexibility in sub-zero temperatures. used in systems irrigation, water installations industrial, for emptying septic tanks etc. On special order Available also version ARIZONA EXTREME ELASTIC flexible in very low temperatures (for -40°C). Hose material: grey and green PVC. Reinforcement: rigid-PVC spiral. Working pressure: from 1.5 bar to 7 bar - depending on the diameter hose and temperatures. Operating temperature: od -25°C up to +55°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, very flexible and pliable, resistant to temperature two-layer hose suction - delivery intended for discharge and conveying vapours, fumes and air o high temperature. flame-retardant, resistant chemical, o fairly sound resistance to hot sparks. used in the structure furnaces (steelworks and foundries metals and glass, industry ceramic and chemical), vehicles (installations discharge exhaust gases, stations testing engines etc.), use aviation and military. It is characterised by high compressibility - up to 1:6, a strong construction, and impact resistance thanks to the external spiral. Also available with a stainless steel spiral (from 80 mm diameter). Assembly of the hose on connectors with bridge clamps (lewo-handed). Standard length: from 2 to 10 m - contact Tubes International. Hose material: 2 layer fabric glass, outer Layer coated silicone (grey). Reinforcement: outer spiral with wire and sheet steel galvanized. Operating temperature: od -50°C up to +450°C (momentarily up to +500°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsColorless, transparent, flexible hose fuel o exceptionally low permeability fumes fuels through wall hose. meets American requirements EPA and CARB (permeability for 15 g/m2/24h). patented multilayer The design hose o internal layer with fluoropolymer PVDF resistant na fuels with content ethanol for 100%. resistant na swelling and hardening na result operation hydrocarbons, reduces significantly risk cracking and leakage. minimum extractability secures cleanliness fuels, a exceptionally low factor penetration substances aromatic secures the operator and environment. resistant na ozone and radiation UV (ANSI B175.1 D). flexibility hose facilitates its installations even in tight places and is maintained also in low temperatures, co ensures trouble-free sampling fuels in each position. transparent wall allows na monitoring flow. thanks to internal layer with PVDF hose is resistant na most substances chemical and fuels. can be submerged in fuel (nie recommended only repeated use in high temperatures external). flame-retardant (UL 94 HB). used in modern mowers, saws chain, drills combustion, trimmers for hedges, itp. machines garden. Length of a full hose roll 15 m. pressure working determined relative to pressure bursting at factor safety 1:5. Material: PVDF / TPE (multilayer). temperature use: from -40°C to +82°C. temperature brittleness: -90°C. Hardness: 78° Shore (A). Density: 1.27 g/cm³. Note: The product is packaged in the Tubes International Clean Zone (CLEAN ROOM) in compliance with rigorous standards. Return of the product after opening the package is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsColorless, glassy transparent, flexible hose free of phthalates and BPA (bisphenol A). intended for conveying and dispensing products food, in particular juices, beverages, water bottled. Nie changes taste and smell products, a properties non-wetting enable total emptying and easy cleaning through flushing. can be used for pumps peristaltic, ale service life is moderate. meets requirements hygienic and for contact with food: European 1935/2004/EC and 10/2011 EU (for conditions and substances acc. to certificate), American FDA, NSF-51, NSF61, 3-A, Japanese #370/1959 and MHLW370(3-D). possible sterilization steam or oxide ethylene. compliant with REACH and California Proposition 65 – nie contains substances hazardous and banned. Length of a full hose roll 15 m (od diameter internal 50.8 mm - 6 m). The given working pressure is determined relative to the bursting pressure at a safety factor of 1:5. Material: PVC (special). Maximum operating temperature: +74°C. temperature brittleness: -36°C. Hardness: 66° Shore (A). Density: 1.21 g/cm³. Note: The product is packaged in the Tubes International Clean Zone (CLEAN ROOM) in compliance with rigorous standards. Return of the product after opening the package is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, flexible hose intended for discharge hot exhaust gases engines petrol and diesel. used as hose workshop unrolled on floor adapted for drum systems winding, hose for channels suction or on stations for testing engines. resistant to creasing thanks to reinforcement white, thick, round spiral nylon (PA), cover with outside black TPE. resistant chemical, in particular on vapours gasoline and oil, a also ozone, hydrolysis, microbes and radiation UV. Not contains halogens and softeners. hose P-G-EX 1 should be used together with with vacuum system discharge exhaust gases, using appropriate connector between a hose a outlet exhaust gases with engine. Other diameters are available on special order in the scope 40 ÷ 250 mm. Assembly of the hose on connectors with bridge clamps (prawo-handed). length standard: 2.5 m, 5 m, 7.5 m, 10 m, 15 m and 20 m. Thickness measured between the spiral: 0.4 mm. Hose material: fabric polyester impregnated black coating TPE (thermoplastic elastomer). Reinforcement: spiral nylon in cover TPE protective against abrasion. Operating temperature: od -40°C up to +150°C (momentarily +170°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong hose suction - delivery, o thick wall, intended for conveying substances food requiring the use of rubber free of odour and taste. Contains no phthalates or bisphenol A. hose specially designed for conveying oils and fats. Widely used in industry oil and fat. Layer outer resistant to fat and aging. standards and requirements : industry food, contact with food 1935/2004/EC and 2023/2006/EC (GMP). Layer inner compliant with FDA 21 CFR 177.2600, D.M. 21/03/73. Inner layer: white NBR rubber/PVC. Reinforcement: two layer cord synthetic, steel spiral. Outer layer: blue, smooth rubber CR. Working pressure: 10 bar. Vacuum: 0.9 bar. Operating temperature: -15°C up to +90°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsResistant to vacuum hose suction-delivery intended for water cooling in smelters, foundries and we all use, where hose rubber works close source heat. coated fiber glass resistant to temperature up to +530°C caused radiation thermal. used in systems cooling. especially recommended for installation water at furnaces metallurgical. resistant to momentary action splashes red-hot hot metal. length standard: 60 m or 120 m. Inner layer: black rubber SBR. Reinforcement: cord synthetic, steel spiral. Outer layer: EPDM rubber / fiber glass. Working pressure: 10 bar. Vacuum: 0.9 bar. Operating temperature: od -40°C up to +70°C, outer up to +530°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, very pliable and flexible, having resistance to creasing and twisting hose intended for discharge dusts, contaminants air, fumes welding. commonly used in systems vacuum cleaners industrial. shaped in profile hose outer spiral reinforcing, left-handed, allows screwing on appropriate ends for vacuum cleaners with thread left (ends plastic o index ME-EVA...). Assembly of the hose with clamps on suitable ends, pipe spigots etc. is also possible. Hose material: grey ethylene-vinyl acetate (EVA). Reinforcement: spiral reinforcing shaped in profile hose. Operating temperature: od -30°C up to +60°C - for hose EVA and od -25°C up to +60°C - for hose EVA IVH (podworking pressure depends on temperature).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible hose suction-delivery intended for conveying food, pharmaceutical and cosmetic substances: water, fruit juices, beer, wine, vinegar, alcohols with a concentration up to 96%, milk and dairy products, creams, soaps, aromatic substances, pigments and others. Resistant to fats and oils within the standard range of use. Good chemical resistance to light chemicals – acid and base solutions. The extruded, completely smooth inner and outer surface of the hose facilitates flow and cleaning. double Reinforcement hose spiral and a braid ensures good strength on overpressure and vacuum. The hose material is not vulcanised, is clean (contains no vulcanising additives), resistant to hydrolysis, does not promote bacterial growth, with low porosity and low permeability. Completely neutral in taste and odour, does not change the organoleptic properties of the medium. resistant to aging, conditions atmospheric and radiation UV. Cleaning, disinfection or sterilisation of the hose must be carried out strictly according to the recommendations given in the catalogue sheet below. Cleaning by the SIP method, which noticeably shortens the service life, is not recommended. Use for high-proof alcohol (its vapours or other flammable substances) requires taking into account the hazards associated with static electricity. standards and requirements : 1) industry food, contact with food: compliant with the European requirements 1935/2004/EC and 10/2011/EU (simulant fluids A, B, C, D1, D2), 2023/2006/EC (GMP) and American FDA 21 CFR 177.2600 „e”. 2) Pharmaceutical industry: USP CLASS VI. Hose material: transparent TPE-S. Reinforcement: a polyester braid, spiral of steel AISI 302. Working pressure: from 7 bar to 17 bar, depending on the diameter hose. Operating temperature: -30°C up to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery Light, flexible hose intended for discharge air, vapours, dust, dusts, very fine fibres, powders, grains, light bulk materials. intended for use in industry food and pharmaceutical. very pliable and very compressible axially, flexible also in low temperatures. O sound resistance to abrasion, resistant to microbes and hydrolysis. non-toxic, Contains no halogen compounds or plasticisers. Resistant to oils and petrol. Assembly on connectors with bridge clamps (prawo-handed). Other diameters may be available on special order. hose Available is in following versions: P2 PU FOOD – spiral with wire steel (copper-plated); P2PU PAS FOOD – spiral with wire of steel stainless, Material hose permanently antistatic (R ≤ 10 8 Ω, in accordance with TRGS 727). hoses P2 PU FOOD and P2 PU PAS FOOD are compliant with requirements European 1935/2004/EC and 10/2011/EU (simulant E), 2023/2006/EC (GMP) and American FDA 21 CFR 177.2600 and 178.2010. are suitable for time contact with food at conveying dry, bulk, free of fat on surface, substances food - on conditions defined in declaration conformity the manufacturer (Available in Tubes International). Hose material: transparent polyether-polyurethane. Wall thickness measured between the spiral: 0.4 mm. Reinforcement: spiral with wire steel (P2 PU FOOD), spiral with wire of steel stainless AISI 301 (P2 PU PAS FOOD). Operating temperature: od -40°C up to +100°C (momentarily for + 125°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, flexible hose suction-delivery intended for water, juices, drinks and other products food. no phthalates in material allows on use hose for conveying milk and its dairy products and alcohols with a concentration up to 50% and temperature up to +60°C. not recommended for oils and greasy substances food. Reinforcement with a rigid-PVC spiral, impact-resistant, provides good resistance to vacuum and kinking of the hose. transparent wall allows on easy visual control of the flow. A smooth inner surface reduces flow losses and ensures ease of cleaning. also surface outer hose is smooth, co facilitates assembly ends using bands or straps, reduces damage external in result abrasion and facilitates maintaining hose in cleanliness. W use not regarding direct contact with food (in industry, construction, agriculture) It can be used both for light chemicals, water, sludge and sewage, other liquids (without fat, oils and hydrocarbons), as and for air, vacuum conveying dusts, powders, granulates and other lightly abrasive substances bulk (not greasy). In that case the abrasiveness and the possible problem of static electricity must be taken into account. as hose reinforced only spiral with hard PVC, not having braid, is characterized a certain elongation under pressure, co should take into account in use, especially in temperatures above +40°C. Standards and requirements: Food industry, food contact: compliant with the European requirements 1935/2004/EC and 10/2011/EU (simulant fluids A, B, C and D1), 2023/2006/EC (GMP). Hose material: transparent PVC. Reinforcement: spiral with hardened PVC. Working pressure: from 3 bar to 7 bar, depending on the diameter hose. Operating temperature: -15°C up to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsExternally Serrated flexible and strong hose suction - delivery for water and sewage. is characterized good resistance on impacts external and heavy conditions use and resistance on radiation UV and low temperatures. used for in systems irrigation, tankers, for rinsing sewers and emptying septic tanks. used also in installations industrial. Hose material: grey-violet PVC. Reinforcement: rigid-PVC spiral. Working pressure: from 3 bar to 8 bar, depending on the diameter hose and temperatures. Operating temperature: od -20°C up to +50°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, flexible and pliable, resistant to temperature hose suction intended for discharge gases, vapours, fumes and air o high temperature. Flame-retardant, to some extent resistant to hot sparks. used mainly in industry metallurgical, foundry, ceramic, glass, at furnaces, engines and as A guard thermal. It is characterised by high compressibility - up to 1:6, a strong construction thanks to glass fabric reinforced with stainless steel threads, and impact resistance thanks to the external spiral. Used only as a suction hose working under vacuum, due to the possibility of gases penetrating outwards under overpressure (degassing). Also available with a stainless steel spiral (from 80 mm diameter). Assembly of the hose on connectors with bridge clamps (lewo-handed). Standard length: from 2 to 10 m - contact Tubes International. Hose material: impregnated fabric glass with fibres of steel stainless, externally grey. Reinforcement: outer spiral with wire and sheet steel galvanized. Operating temperature: od -50°C up to +400°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery light and flexible hose suction-delivery, intended for applications general-industrial (in industry, construction, agriculture). It can be used for water, light chemicals, sludge and sewage, agents protection plants, other liquids (without fat, oils and hydrocarbons) as well as for air, vacuum conveying dusts, powders, granulates and other lightly abrasive substances bulk (non-greasy). In that case the abrasiveness and the possible problem of static electricity must be taken into account. W industry food It can be used for conveying food hydrated, acidic, alcohols for 20% np. juices, drinks, beer, wine,(simulants A, B, C; up to +60°C and 2 h). Not recommended for milk and dairy products or oils and greasy food substances. Reinforcement with a rigid-PVC spiral, impact-resistant, provides good resistance to vacuum and kinking of the hose. A smooth inner surface reduces flow losses and ensures ease of cleaning. The outer surface is lightly corrugated, smooth for small diameters. hose FLORIDA complies with the European requirements 1978/142/EEC, 1935/2004/EC, 1895/2005/EC and 10/2011/EU (simulants A, B, C), 2023/2006/EC (GMP). Suitable for temporary contact with food when conveying food substances - under the conditions specified in the manufacturer's declaration of conformity (available at Tubes International). Hose material: transparent PVC. Reinforcement: rigid-PVC spiral (grey). Working pressure at a temperature of 20°C: from 3 bar to 6.5 bar - depending on the diameter hose. As the working temperature rises, the hose's working pressure value decreases. Operating temperature: from -5°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPliable, light and strong hose suction-delivery intended for conveying water, sewage, sludge, liquids non-corrosive, fertilisers natural (slurry). Layer inner with smooth rubber synthetic, resistant to sludge and sewage. corrugated Layer outer ensures small radius bends and is resistant to ozone, conditions atmospheric and aging. intended for applications agricultural, construction and industrial, used for emptying septic tanks, as hose suction for pumps water and sewage, for dewatering and irrigation, for tankers. can be used for extraction air, dust and for bulk materials. assembly – depending on the diameter and type fittings using bands steel, straps, clamps or ferrule clamping. Inner layer: black synthetic rubber (SBR). Reinforcement: cord synthetic, steel spiral. Outer layer: black corrugated synthetic rubber. Working pressure: 3 bar. Operating temperature: od -30°C up to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, very pliable and flexible hose intended for extraction hot vapours, fumes, gases, air blowing and discharge air cooling. resistant chemical, on radiation UV and aging. used m.in. for extraction gases in industry metallurgical, foundry, industry glass and ceramic, for hot air in dryers industrial, in printing houses and paper mills, in vehicles and engines for air cooling, incineration plants, a also for extraction exhaust gases and gases welding. smooth inside (in state extended), o very small radius bends enabling easy installations in tight spaces equipment and vehicles. not recommended for continuous dynamic bending. Assembly with clamps. Other diameters are available on special order. Hose material: fabric glass impregnated red silicone. Reinforcement: inner spiral with wire steel, outer cable with fibre glass. Operating temperature: od -70°C up to +250°C (momentarily up to +300°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong, thick, flexible hose intended for extraction and conveying granulates and other bulk materials. intended for use in many types industry. used m.in. granulate plastics, materials insulating, waste, sand and other materials construction. fairly pliable, little compressible, smooth inside, flexible also in low temperatures. O sound resistance to abrasion, resistant to microbes and hydrolysis. non-toxic, Contains no halogen compounds or plasticisers. Resistant to oils and petrol. Assembly on connectors with bridge clamps (prawo-handed). can be available other diameter. besides version standard P7 M PU AE hose Available is in version P7 M PU EL conductive electrically (R ≤10 4 Ω), compliant with ATEX 2014/34/EU, TRBS 2153 and for extraction also with TRGS 727, can be ona used in zones hazard explosion po carrying out analysis risk. Hose material: polyether-polyurethane. Wall thickness measured between the spiral: 1.4 mm. Reinforcement: spiral with wire steel. Operating temperature: od -40°C up to +100°C (momentarily for + 125°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery strong and thick, flexible hose intended for extraction and conveying abrasive bulk materials, granulates, sand, gravel, pebbles, substrate agricultural. used for loading and emptying silos, vehicles and excavators suction, handling with tankers etc. thick wall and fairly dense spiral reinforcing ensures high resistance to pressure and vacuum. smooth inside, non-compressible, fairly pliable (r=2.5xD), flexible also in low temperatures. hose o sound resistance to abrasion, resistant also on oils and gasoline. Assembly on connectors with bridge clamps (prawo-handed) or assembly special on ends industrial e.g. flange. Other diameters may be available on special order. versions: P3 SV PU – with polyester – polyurethane, very resistant to abrasion; P3 SV PU AE - version with polyether – polyurethane, resistant to abrasion, resistant to microbes and hydrolysis, compliant with the European requirements 1935/2004/EC and 10/2011/EU (simulant E), 2023/2006/EC (GMP) and American FDA 21 CFR 177.2600 and 178.2010. is suitable for time contact with food at conveying dry, bulk, free of fat on surface, substances food - on conditions defined in declaration conformity the manufacturer (Available in Tubes International). Hose material: transparent polyester-polyurethane (P3 SV PU), polyether – polyurethane (P3 SV PU AE). Wall thickness measured between the spiral: 2.5 mm. Reinforcement: spiral with wire steel. Operating temperature: od -40°C up to +100°C.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible hose suction intended for sewage and water. externally Serrated, almost smooth in center. special profile makes, that hose is resistant to vacuum and creasing, (returns for its shape). as hose with polyethylene has very good resistance chemical and resistance to corrosion biological (rotting, rotting). is flexible in low temperatures. hose is commonly used for emptying septic tanks and portable toilets, in construction, facilities tourist, in marinas and on airports. Hose material: yellow profile polyethylene (PE). Reinforcement: black profile polyethylene (PE). Vacuum: 0.95 bar (for diameter 51mm ÷ 76 mm); 0.85 bar (for diameter 102 mm). Operating temperature: od -40°C up to +60°C.- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong hose suction-delivery intended for greasy and non-greasy substances food, requiring the use of rubber free of odour and taste. Contains no plasticisers, phthalates or substances of animal origin. especially recommended for handling and heavy conditions use. widely used in industry food in dairies and oil mills. Layer inner made with NBR resistant is on standard used in industry food agents and processes cleaning. Layer outer resistant to momentary contact with fats animal and vegetable, abrasion and conditions atmospheric. standards and requirements : 1) general: EC 2002/95 (RoHS), EC 1907/2006 (REACH). 2) industry food, contact with food: EC 1935/2004, EC 2023/2006 (GMP). Layer inner compliant with D.M. 21/03/73, FDA 21 CFR 177.2600, BfR, 3A Sanitary Standards. RAL (German institute ensuring quality and certification). Vacuum: 0.9 bar. Inner layer: white NBR rubber. Reinforcement: cord synthetic, steel spiral. Outer layer: blue rubber CR. Working pressure: 10 bar. Operating temperature: from -20°C to +90°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, exceptionally flexible and compressible hose intended for air conditioning, discharge and air blowing air, extraction fumes welding. Widely used for arms ducting, ventilation, heating tents, drying the structure construction. self-extinguishing and non-flammable (non-spreading flame) in accordance with UL94 V-0. resistant to hydrolysis and microbes. Other diameters are available on special order in the scope 30 ÷ 800 mm and color: black, blue, white and yellow. Assembly of the hose on connectors with bridge clamps (prawo-handed). Hose material: fabric polyester impregnated grey PVC. Wall thickness: 0.4 mm. Reinforcement: spiral with wire steel. Operating temperature: od -30°C up to +80°C (momentarily up to +100°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, very pliable and flexible hose intended for extraction hot vapours, fumes, gases, air blowing and discharge air cooling. reinforced version hose NEOPRENE 1, o two layers fabric impregnated neoprene and spiral steel placed between layers. resistant chemical, on radiation UV and aging. used m.in. for hot air in dryers granulate and blow-moulding machines film in processing plastics, in dryers paints in printing houses, other dryers industrial, in industry electronic, in vehicles and engines for air cooling, incineration plants, a also for extraction exhaust gases and gases welding. smooth inside (in state extended), o small radius bending enabling easy installations in tight spaces equipment and vehicles. Assembly with clamps. Other diameters are available on special order. Hose material: two fabric glass impregnated black rubber CR (neoprene® - rubber chloroprene). Reinforcement: spiral with wire steel, on outside two cable with fibre glass. Operating temperature: od -35°C up to +135°C (momentarily up to +150°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery Light, flexible, having resistance to creasing hose intended for discharge air, fumes, dusts fibres, dust and other light substances. used in vacuum cleaners industrial. made with conductive polyethylene (PE) and elastomer, o low resistance material, excellent for applications in which required is avoiding accumulation charges electric (should then effectively earth hose). shaped in profile hose outer spiral reinforcing, left-handed, allows screwing on appropriate ends for vacuum cleaners with thread left e.g. ends plastic for hose EVA: DN32, 38 and 50 or appropriate ends conductive. Assembly of the hose with clamps on suitable ends, pipe spigots etc. is also possible. hose o diameter DN38 and DN50 has declaration conformity with requirements ATEX and standards TRGS 727 and It can be used in zones hazard explosion, under a condition effective earthing hose and carrying out through user analysis risk. Hose material: black special polyethylene (PE) and elastomer. Reinforcement: spiral reinforcing shaped in material hose. Operating temperature: od -20°C up to +60°C (podworking pressure depends on temperature).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery light, very flexible and pliable hose intended for discharge aggressive vapours chemical and gases, ventilation and air conditioning. good resistance chemical on solvents and other aggressive vapours. Checking chemical resistance - the chemical resistance table for polyethylene (preliminary selection), confirmation of resistance and conditions of use - by Tubes International. resistant to hydrolysis and corrosion biological. Contains no halogen compounds or plasticisers. used mainly in industry chemical. on request available diameter in the scope 40 ÷ 610 mm. hose occurs in two versions: P2PE - standard and P2PE EL - conductive electrically o resistance R ≤10 4 Ω, compliant with the directive ATEX 2014/34/EU and the standard TRGS 727, made with black polyethylene. Hose material: polyethylene (PE), transparent - version standard P2PE, black - version conductive electrically P2PEEL. Wall thickness: 0.4 mm. Reinforcement: spiral with wire steel. Operating temperature: od -40°C up to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, flexible hose medium wall thickness intended for extraction and conveying powders, grains, light granulates and other bulk materials. intended for use in industry food and pharmaceutical. used m.in. for milk in powder, grain, rice, coffee, tea, flour (version PAS). pliable, fairly compressible, almost smooth inside, flexible also in low temperatures. O sound resistance to abrasion, resistant to microbes and hydrolysis. non-toxic, Contains no halogen compounds or plasticisers. Resistant to oils and petrol. Assembly on connectors with bridge clamps (prawo-handed). Other diameters may be available on special order. hose Available is in following versions: P7 OL PU FOOD – spiral with wire steel (copper-plated); P7 L PU PAS FOOD – spiral of steel stainless, Material hose permanently antistatic (R ≤10 8 Ω, in accordance with TRGS 727). hoses P7 OL PU FOOD and P7 L PU PAS FOOD are compliant with requirements European 1935/2004/EC and 10/2011/EU (simulant E), 2023/2006/EC (GMP) and American FDA 21 CFR 177.2600 and 178.2010. are suitable for time contact with food at conveying dry, bulk, free of fat on surface, substances food - on conditions defined in declaration conformity the manufacturer (Available in Tubes International). Hose material: transparent polyether-polyurethane. Wall thickness measured between the spiral: 0.7 mm. Reinforcement: spiral with wire steel (P7 OL PU FOOD), spiral with wire of steel stainless AISI 301 (P7 L PU PAS FOOD). Operating temperature: od -40°C up to +100°C (momentarily for + 125°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrength, light and very flexible (also in low temperatures) hose suction-delivery designed specially for industry wine for heavier conditions use. strong than hose SPIRABEL ® SNTS, o thicker wall. hose for demanding applications, intended for conveying water, beer, good win and alcohols with a concentration up to 50% and temperature up to +40°C, juices, drinks and other products food. Not contains phthalates, co allows use go also for milk and its dairy products. not recommended for oils and greasy substances food. Reinforcement spiral with hard PVC, resistant on impact, ensures very good strength on vacuum and kinking hose. transparent wall allows on easy control visual movement substances. smooth surface inner reduces losses flow and ensures ease cleaning. ease cleaning, ensures also smooth surface outer, which available in hoses for diameter 63 mm. W use not regarding direct contact with food (in industry, construction, agriculture) It can be used: 1) for light chemicals, water, sludge and sewage, other liquids (without fat, oils and hydrocarbons); 2) for air, vacuum conveying dusts, powders, granulates and other lightly abrasive substances bulk (not greasy). In that case the abrasiveness and the possible problem of static electricity must be taken into account. as hose reinforced spiral with hardened PVC (without braid) is characterized a certain elongation under pressure, co should take into account in use, especially in temperatures above +40°C. Standards and requirements: Food industry, food contact: compliant with the European requirements 1935/2004/EC and 10/2011/EU (simulant fluids A, B, C and D1), 2023/2006/EC (GMP). Hose material: transparent PVC. Reinforcement: spiral with hardened PVC. Working pressure: from 5 bar to 7 bar, depending on the diameter hose. Operating temperature: -25°C up to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery light and flexible hose intended for discharge air, dust, dusts, fine sawdust and chips, very light bulk materials etc. Dla all types industry, in particular often used for dedusting and discharge fine particles solid in industry wood, furniture, ceramic, plastics. very pliable and very compressible axially, flexible also in low temperatures. O sound resistance to abrasion, resistant also on microbes and hydrolysis. Not toxic, Contains no halogen compounds or plasticisers. Resistant to oils and petrol. hose marked is an arrow indicating correct direction flow medium. The hose wall thickness is measured between the spiral. Assembly on connectors with bridge clamps (prawo-handed). Other diameters may be available on special order. hose Available is in following versions: ECO – version standard, ECO SE – version with material flame-retardant (without classification flame retardancy), ECO AS – version permanently antistatic (ISO 8031: R 9 Ω, TRGS 727 (6.4.2.4): R 8 Ωm, directive 2014/34/EU (ATEX): It can be used in defined zones hazard explosion po analysis risk, ECO SE AS – version antistatic and flame-retardant (Available on special order). hose ECO produced is in process production compliant with with policy sustainable growth in which uses raw materials originating with recycling pure waste with process production, energy renewable, closed circulation water and other innovation. Hose material: transparent polyether-polyurethane. Reinforcement: spiral with wire steel. Wall thickness measured between the spiral: 0.4 mm. Operating temperature: od -40°C up to +100°C (momentarily for + 125°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose suction-delivery for demanding, versatile applications in industry food. excellent for conveying many types products food such as: olive oil, wine, beer, juices fruit, milk, fats and alcohols with a concentration up to 96%. The inner layer is free of phthalates, plasticisers and components of animal origin. Contains no phthalates or bisphenol A and no polycyclic aromatic hydrocarbons (PAH Free), in accordance with ZEK 01.4-08 Cat.1. Tested for the presence of heavy metals. Layer outer resistant to conditions atmospheric and ozone. thanks to external corrugation hose is exceptionally pliable and flexible. recommended way mounting with fitting are special clamp shell EASY SHELL, o shape adapted for serrated hose. standards and requirements : industry food, contact with food 1935/2004/EC and EC 2023/2006/EC (GMP). Layer inner compliant with FDA 21 CFR 177.2600, BfR XXI kat. 2, D.M. 21/03/73, 3-A Sanitary Standard 18-03 class II. Inner layer: white, smooth synthetic rubber. Reinforcement: cord synthetic, spirals steel. Outer layer: blue synthetic rubber. Working pressure: 10 bar. Vacuum: 0.6 bar. Operating temperature: from -30°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, single-layer, very pliable and flexible hose intended for extraction hot vapours, fumes, gases, air blowing and discharge air cooling. resistant chemical, on radiation UV and aging. used m.in. for hot air in dryers granulate and blow-moulding machines film in processing plastics, in dryers paints in printing houses, other dryers industrial, in industry electronic, in vehicles and engines for air cooling, incineration plants, a also for extraction exhaust gases and gases welding. smooth inside (in state extended), o very small radius bends enabling easy installations in tight spaces equipment and vehicles. Assembly with clamps. Other diameters are available on special order. Hose material: fabric glass impregnated black rubber CR (neoprene® - rubber chloroprene). Reinforcement: inner spiral with wire steel, outer cable with fibre glass. Operating temperature: od -35°C up to +135°C (momentarily up to +150°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrength, light and flexible hose suction-delivery designed specially for industry wine for heavier conditions use. strong than hose LUISIANA, o thicker wall. hose for demanding applications. intended for conveying water, beer, good win and alcohols with a concentration up to 20%, juices, drinks and other products food. Not contains phthalates. not recommended for milk and its dairy products, oils and greasy substances food. Reinforcement spiral with hard PVC, resistant on impact, ensures very good strength on vacuum and kinking hose. transparent wall allows on easy visual control of the flow. A smooth inner surface reduces flow losses and ensures ease of cleaning. W use not regarding direct contact with food (in industry, construction, agriculture) It can be used: 1) for light chemicals, water, sludge and sewage, other liquids (without fat, oils and hydrocarbons); 2) for air, vacuum conveying dusts, powders, granulates and other lightly abrasive substances bulk (not greasy). In that case the abrasiveness and the possible problem of static electricity must be taken into account. standards and requirements : industry food, contact with food - compliant with the European requirements 1935/2004/EC and 10/2011/EU (simulant fluids A, B and C), 2023/2006/EC (GMP). Hose material: transparent PVC. Reinforcement: rigid-PVC spiral. Operating temperature: from -5°C to +60°C.
